Search results for query: *

  1. G

    Patch routing help

    I've found depending on what effects I use in a chain my amp tone always sounds different, Is there a way I can have the amp tone separate from everything but have a side chain that activates only when I need a specific effect? I'm sure there are ways to do this,I'm just not very technically...
  2. G

    Fender treadlight expression pedal???

    Does this pedal work with Fractal products???
  3. G

    Switches capability question....

    I've been using my FM3 with a Morningstar Mc6,I'm about to use the FM3's switches for the first time, On the MC6 I can Hold a button down to say activate a Harmony on scene2,that scene will stay active until I release the switch,then it will return to, as I've programmed it, scene 1. Can I...
  4. G

    FM3 Firmware Version 3.03 beta 1

    FM3 noob here,Is there an issue where output 2 isn't loud enough or is it just a matter of cranking everything up? I'm close to clipping already,I noticed out 2 has its own graphic eq,do I just raise the gain there?
  5. G

    Pantera - Vulgar Display of Tone Match!

    Im loving the tone 🤘 By any chance,have you purchased an Axe fx3 or Fm3 and done an updated Dime tone? I play in a Pantera tribute Band and am currently trying to get a Pantera tone happening for my band, Any tips would be appreciated too, Cheers
  6. G

    How Will Cygnus Affect Existing Presets?

    So this update only changes the amp block? Overdrive,distortion pedals stay the same?
  7. G

    FM3 Scene Switching Lag

    What percentage of CPU are your patches using? I've only had that when using more than 80%
  8. G

    Let's see those FM3 rigs!

    Where did you get the colored Nuts from? Do you remember the size etc,thanks
  9. G

    Auto-engage wah to auto off faster?

    My auto engage wah works great but I find the auto off for my wah is quite slow, Can you set it to auto off faster? I remember my Axe fx2 was noticeably faster to deactivate,and I think it had separate settings for on and off
  10. G

    Let's see those FM3 rigs!

    Nux bumble bee board owners,has anyone tried to fit a Matrix 1000 1unit in the bag? Im wondering if there's room for the matrix with the nux board on top
  11. G

    Mission Engineering Hex key size?

    as the title says,my Mission engineering ep1 has gone very loose but I dont have and know the size of the hex key I need to tighten it, I've googled and havn't found anything, does anyone know?
  12. G

    Adding a toe switch to an EV-2?

    I'm curious to add a toe switch too, theres another thread here where a guy added a Toe switch to a EV1,hopefully the EV2 can work as well
  13. G

    Modding the EV-1 with a foot switch!

    Does this work with the smaller ev2???
  14. G

    MC6 question about hold function

    Another option that works for me,cheers dude
  15. G

    MC6 question about hold function

    That did it,thanks man \m/
  16. G

    MC6 question about hold function

    Thanks I'll give that a try when I get home,cheers
  17. G

    MC6 question about hold function

    I'd like to Hold a Mc6 switch down to activate some delay, and then release the switch to deactivate said delay,this would be an easy answer for my current set up, is this possible?
  18. G

    FM3 + Morningstar MC6 = does the USB Type A Supply Power ?

    I use a small power bank to run my MC6,its velcroed to the side of the unit and plugged in using the provided USB cable, works great,the Powerbank is 6,700ma I believe, and after a 3 hour rehearsal still had 4 out of 4 capacity lights lit up
  19. G

    Post Here if You've Received An FM3 Invite!

    Does the US/Canada wait list have to be completed before other territories receive invites? I'm Asking specifically regarding Australia, Thanks
  20. G

    FM3 dimensions question...

    Good idea,turns out the FC6 is 283mm x 233mm x 88mm , so the rails stick up from the units face 15mm, thanks mate
  21. G

    FM3 dimensions question...

    281mm x 236mm x 103mm The 103mm measurement,Is that from the bottom of the unit to the top of the rails? or the bottom of the unit to the highest face of the unit,with the rails as an addition on top of that, hope I made sense lol cheers
  22. G

    Let's see those FM3 rigs!

    Leon,Ragdoll and his FM3 rig tonight in Melbourne,Australia,sounded awesome \m/
  23. G

    [Chart] FM3 Block CPU Usage Estimates

    Glad FM3 doesn't run on Windows
  24. G

    [Chart] FM3 Block CPU Usage Estimates

    The base cpu @11 % Is this used at all times as default by the System? So we lose 11% straight off the Bat?
  25. G

    What is the cpu usage for each effect/action?

    That would be amazing! I'm sure alot of people will be looking forward to seeing it,cheers
  26. G

    What is the cpu usage for each effect/action?

    As the title says I'd like to know,if possible,what cpu each block or action uses, I'm curious to write out some "Virtual" presets to see if they would possibly work, cheers
  27. G

    FC 6/12 Alternatives for your FM3

    I'll probably rough it with a 2 button external switch and a expression pedal front of stage,while keeping the FM3 behind me on my amp, then maybe get a Morningstar mc6 down the line
  28. G

    Global out 1 eq, but no out 2 eq?

    Eq on output 2 and Global blocks please
  29. G

    Only Use 1 Amp Block At A Time?

    Does this mean you can have 4 different amps? 1 per channel? So mesa channel 1 5150 channel 2 Marshall channel 3 Soldano channel 4? Or Is it the same one amp with different settings on each of the 4 channels if you wanted? Or something different again lol Also Is there a difference in speed...
  30. G

    How will you use the FM3? Share your upcoming rig ideas!

    I'd have 2 set ups,where there is no danger of Beer spillage I'd go Sennheiser wireless xsw/FM3/2 external switch/expression pedal/matrix Gt1000/Mesa 4 x 12 cab \ Cab sim to FOH or for risky gigs...
  31. G

    Post Here if You've Received An FM3 Invite!

    Is it stated any where why there is no HP jack on the early units? Just curious cheers
  32. G

    Anyone tried a MIDI expression pedal foot controller?

    Hi,I'm currently running a RJM Mastermind,it has a Midi in and out so I assume that means I can run another midi device through it? I've never really gone in depth with midi so I'm still very new. I'm just keen to if possible get a wah going I can switch on and off with a toe switch
  33. G

    Anyone tried a MIDI expression pedal foot controller?

    I'm curious about expression foot controllers that send midi signal instead of the usual guitar lead style,especially if they have an on/off swtich such as on a normal wah pedal. I'm an Axe fx 2 user with only one input jack,not looking to upgrade or change to an MFC for the extra pedal...
  34. G

    Wah setting's tip's

    Anyone got any tip's on how to get the wah wah to sound more exaggerated for high gain amps? cheers
  35. G

    Light weight Gator case.....

    Anyone got one of these? Don't think an Axe fx2 will fit in this thing,can anyone out there verify, thanks Gator GR-RACKBAG-3U - 3U Lightweight rack bag | Sweetwater.com
  36. G

    speaker powering question...

    thanx for the feedback! after considering my options and finance's I'm gonna go with the Fryette 2 90 2 \m/ may even try it stereo mode to my stereo cab and put a slight delay,see if I can thicken the tone a little that way, just an idea,cheers!
  37. G

    speaker powering question...

    Hi,i'm looking to buy a Fryette power amp,either 50 watt stereo or 90 watt stereo, I have a 100 watt Marshall and am downsizing to one of the above, my cab is a Mesa stilletto with stereo capability, my query is,can a 50 watt per channel stereo poweramp,like those mentioned previously,run...
  38. G

    Ice Pick Tone!

    maybe try going to amp block,page across to speaker settings and adjust something called xfrmr hf,drop that alot can help with ice pick
  39. G

    Alright 10.06 high gain players - Thunk/Motor Drive - who's using 'em?

    never use these 2 parameters but willing to give it a try, My signal chain is usually PEQ(frown)- Drv(Rat) - AMP(Fas) - PEQ(smiley) If drive can grit up my signal with less noise that'll be Awesome! I could use less gate for my Dime squeals \m/
  40. G

    wah travel question...

    Can I set the lowest frequencys of the wah to take up more pedal travel? My auto engage is set at %10,so I want some play at the lower range to avoid turning the wah off by accident cheers
  41. G

    Will a 600watt guitar cab blow my 100 watt tube amp?

    Ok I think I understand,my cab is a Mesa stilletto cab,I wasn't totally happy with the V30's so I swapped them over with the V12 super lynche's. The V30's were 8 ohms,so are the Super lynch,so same wiring set up different speaker. Amazing low end!
  42. G

    Will a 600watt guitar cab blow my 100 watt tube amp?

    Got a 4x12 cab full of Super lynch V12 speakers rated at 150 watts each,8 ohms, running it with a JVM 410 100 watt valve head, With a combined 600 watts Is there a danger of blowing my amp? Is it just a matter of not getting too loud and pushing the amp too hard? I dont really understand...
  43. G

    Cheap way to add Pedal ports???

    thanks for the comments, In the end i'm probably just going to be patient and get a MFC 101, FCB1010 works fine and will make a great back up, I see its highly moddable too which is a bonus
  44. G

    Cheap way to add Pedal ports???

    GORDIUS Little Giant I've been looking some time now for a product like the Gordius module above that can add EXP Pedal ports, Does anyone know of other alternatives? Not a fan of auto engage,I currently use a FCB1010 and would like to try a Mission SP1 pedal, Cheers
  45. G

    Firmware Version 10.06 Now Available

    True that,I'm going to adopt your strategy,thats a good idea
  46. G

    Firmware Version 10.06 Now Available

    I was thinking the same thing,leave current presets as is and anything new is from the latest installed firmware It would be so cool having constant access to the tones from previous FW releases too
  47. G

    Firmware Version 10.06 Now Available

    Cant wait to hear the Fas modern 2 \m/
  48. G

    Version 9.o2 download???

    Awesome! thanx heaps \m/
  49. G

    Version 9.o2 download???

    Hi,I realise the Fractal team are doing everything they can to fix the flub issue's in certain version 10 amps, thats very cool. As i'm farely new to Axe fx I jumped from I think FW7 straight to FW10.02, so i'm asking is there a FW 9.02 download on site? A google search and Fractal...
  50. G

    Mesa Boogie Mark IV / IIC+ tones

    +1 for patches!
  51. G

    Multiband Compressor - tightening the low end in high gain rhythm gtrs

    Exactly what i've been needing for my patches,cheers
  52. G

    Multiband Compressor - tightening the low end in high gain rhythm gtrs

    So if I scoop the mids in a tone,this will help tame that overwhelming speaker rattling bass (at high volumes) thats left over? Sure I could back the bass down but that generally kills the tone, Gotta give this a try thanx
  53. G

    Can a wah on auto engage be programmed to activate another preset....

    Thanks guys,i've hooked it up as suggested,works like a charm :)
  54. G

    Can a wah on auto engage be programmed to activate another preset....

    What i'd like to do is go from my rhythm preset(which is almost totaly dry) activate my wah on auto engage and have reverb,delays,level boost for leads come in etc, then deactivate wah and be taken back to my Rhythm preset. Can the auto engage wah take you to and from another wah patch? Is...
  55. G

    Help with Dimebag tone....

    That Fas modern is quite a Brutal amp indeed! as are the others you mentioned,I think the Fas does everything I need,menacing tone,good for artificial harmonics and Dime squeals catch quite easily! I'll prob have to watch my mids so I dont drown out the other guitarist,as well as Pantera we are...
  56. G

    Help with Dimebag tone....

    eljodon i've used all your tips in a patch and come up with a rough tone that blows away my other tones lol, only thing extra I have is a physical MXR 10 band eq between the Axe fx and my JVM's poweramp input, only because I like the way it colors the tone(like a very mild chorus) and the...
  57. G

    LF Resonance Fix for Boomy FRFR

    I had flubber issues too after the FW10 update so I went to the amp block,held down the bypass button to reset it to default settings....no more flubber problems with that particular amp
  58. G

    Help with Dimebag tone....

    schlagdog,I think the tone match I have must be your one,after 20 years of listening to Pantera I almost crapped myself when I heard it through my headphones! Such a nice thick tone to jam with! Has anyone tried with success to EQ out a cabinet? say if we knew what frequencys a particular cab...
  59. G

    Toneblock question...

    thank you,i'll delete this one
  60. G

    Toneblock question...

    Hi,does anyone know if for example I have a Dimebag tonematch block,i'm farely sure he used V30 speakers in his cab, can I subtract the V30 cab from the toneblock and be left with the pure amp sound???
  61. G

    Help with Dimebag tone....

    Tried google,taken notes already was hoping for Axe fx specific tips for amp to use etc,thanks for the CCV-100 i'll give it a try tomorrow, 1.30am here in Australia, I'm aiming to use my JVM and physical Mesa cab to take over this town \,,/
  62. G

    Help with Dimebag tone....

    Anyone got some good advice on nailing his tone? Amp,effects etc I'm playing in a Pantera tribute band \m/ and need an amp sound to go through a Mesa stilletto cab. I have Dean guitars,Axe fx runs into poweramp input of a JVM 410,also have Matrix GT1000fx as a back up, thanks in advance for any...
  63. G

    Noise gate for high gainers

    A different approach to keeping the noise low: try a Vol block with the volume parameter tied to the Envelope controller. As long as you don't hit the strings, the (input) signal is off. I like using this version for rock,bluesy stuff,works a treat
  64. G

    how to make a wah wah also level boost when activated?

    thanks! didnt see that control,Axe is a bit overwhelming but awesome!
  65. G

    how to make a wah wah also level boost when activated?

    Hi,noob here,I have a mission ep 1 pedal and i'd like to use it as a wah with a level boost for my leads,eg rythm channel - engage wah with level boost for lead - disengage wah back to rythm channel? any help would be appreciated \m/
  66. G

    PANTERA DIMEBAG'S TONE!!! "WALK"....I'm blown away!!!

    just spent all day fiddling trying to get a few new tones and you just blew them all away with this one! So accurate its crazy,cranking Walk through my Dimebolt,I guess its the compulsory first song with this tone \,,/
Back
Top Bottom