Search results for query: *

  1. j20056

    FCB1010 users - Eureka Prom or Uno or Stock?

    I have used the FCB1010 stock model for a long time and yet I just discovered two tricks recently that basically enable stomp mode. Say a block is assigned to CC#30. What I do is set the patch to send two CC's to #30, respectively 127 and 0. In turn, it basically acts as a toggle for the block...
  2. j20056

    Why is it necessary to apply high/lo pass filters to cabs?

    I tried Tone Match (CabClone versus amp only AxeFX) but unsure I did it right, as it seems unclear what input it's using as the volume adjustments thereof don't seem to impact the levels measured. So the actual levels not matching measn nothing, the sahpe matters more I suppose. In addition...
  3. j20056

    Why is it necessary to apply high/lo pass filters to cabs?

    Thanks all. I think the purpose of my initial question got diluted, but I still think there is value in knowing how to set the modeled amp +cab to match what I hear in my studio from the real amp+cab. I also agree that the real goal, which becomes 100% subjective and song dependent, is to...
  4. j20056

    Why is it necessary to apply high/lo pass filters to cabs?

    Thank you. The topic was to compare a real guitar amp+cab on a standalone basis versus modeled and I think we have achieved that. The topic of how to make a guitar sit in the mix is way more complex and subjective as there is no comparison tone to try and match. But having a starting point that...
  5. j20056

    Avoiding OUT1 and XLR to TS for 4 cable method

    I see page 38 of the manual recommends to use one of the XLR of output 1 to go back to the FX return amp via a female XLR to male TS mono cable. However, this means that I lose output q which I could otherwise use to feed into a stereo monitoring system for studio usage. Instead of that, is...
  6. j20056

    Why is it necessary to apply high/lo pass filters to cabs?

    I mostly used my ears, but as far as modeled amp+cab sounds (or real preamp into modeled cab via 4CM), I wanted to see the theory aspect. So I looked carefully at the signal levels frequency via the SSL Realtime Frequency Analysis meter plugin in my DAW and there is quite a bit (meaning -60/70db...
  7. j20056

    Why is it necessary to apply high/lo pass filters to cabs?

    Thanks all. My context was slightly more on the engineering side because my use case as a brand new III owner is a MarkV:25 with a 1x12 Mesa cab in the control room which is my sound room basically and is small. I am only focused on playing right now which eliminates recording subjectivity if...
  8. j20056

    Why is it necessary to apply high/lo pass filters to cabs?

    Thanks. I guess my question was more about the theory of cab modeling. I understand nuances and preferences and micing method impact. But fundamentally, does cab modeling technology capture the inherently limited frequency response of a 8-12 inch speaker? In other words if I apply no hi:low...
  9. j20056

    Why is it necessary to apply high/lo pass filters to cabs?

    Is the design of the cab modeling technology such that it inherently does not capture the frequency response of a speaker cab? It seems like a requirement to apply at least a low pass to cut the highs to get a more realistic cab sound. Assuming that is the case, one would expect that a given cab...
  10. j20056

    Input 1 gate vs using a Decimator.

    I have both the Decimator pedal and the stereo rack unit. The rack unit is much more advanced has it has a dedicated guitar "tracking" input/output which goes at the very very beginning of the analog signal chain just before entering the AxeFX preamp (In 4CM method). In turn, the actual signal...
  11. j20056

    AxeFXIII MIDI Input receives TONS of messages

    OK, thanks. I unplugged all expression pedals and the SSL UF1/UF8 and it made no difference BUT... as soon as I quit Axe-Edit, then all MIDI traffic stops, to @GlennO's keen observation.
  12. j20056

    AxeFXIII MIDI Input receives TONS of messages

    As I was debugging some MIDI issues, I used a software called MIDI Translator, which can show all MIDI messages in any Input or Output ports of any device in the MIDI chain, including MIDI over USB. To my surprise, and without doing anything, the MIDI In gets bombarded by incoming MIDI signals...
  13. j20056

    Setting Initial Value of Volume Modifier

    I have to figure out the loop back issue. I also use a software called Bome Midi translator, and it can send any arbitrary set of MIDI messages when triggered by any PC or CC message, if programmed correctly. Hopefully will help me trace the loopback issue as I still would prefer the MIDI block...
  14. j20056

    Setting Initial Value of Volume Modifier

    I am going to try and take the MIDI connection to the computer (via Focusrite interface) out of the MIDI loop to see what happens. The FCB1010 has a parameter for MIDI merge (assuming it works).
  15. j20056

    Setting Initial Value of Volume Modifier

    Looked at Uno2. Are you using it? Seems powerful and I like the programming language. Unsure it would solve my issue though.
  16. j20056

    Setting Initial Value of Volume Modifier

    Thanks @GlennO. I cannot seem to get your first suggestion to work, adsding the CC into9 the MIDI block does nothing. It seems that the message is sent but it is not received at the end of the chain. My MIDI chain is as follows: FocusRite MIDI out -> AxeFX In -> AxeFX Out -> Behringer FCB1010 In...
  17. j20056

    Setting Initial Value of Volume Modifier

    The Axe is indeed in a MIDI loop with 3 other devices, so this is why I was hoping it would indeed send back to itself, but it doesn't seem to work.
  18. j20056

    Setting Initial Value of Volume Modifier

    Sorry to bump this. Anyone knows if it is possible for a MIDI block to send a CC to the AxeFX, i.e. some sort of loopback?
  19. j20056

    Setting Initial Value of Volume Modifier

    that's a great idea and easy to do as MIDI blocks work at the scene level. However, using Scenes to send MIDI CC requires using the MIDI block. But how can I get the AxeFX to send a MIDI message to itself? Say my expression pedal is on CC #29, what MIDI channel number am I supposed to use in the...
  20. j20056

    Setting Initial Value of Volume Modifier

    Revisiting the above. As mentioned earlier, I got it to work at the preset level but not at the scene level. Now say I have a preset with 2 scenes, but each scene needs the default controller value to be different? Is the only solution to save 2 presets?
  21. j20056

    Sets and Songs - Only works with FC6/12?

    I wanted to confirm that the Sets and Songs capability only works with a FC6/12 controller? I don't inte3nd to buy one of those as I am controlling my AxeFxIII with a simpler (but powerful) Behringer FCB1010. Just wanted to confirm.
  22. j20056

    Best way for adding an octave

    difficult to use virtual capo for a beginner? what does that even mean? Anyways I'm good here
  23. j20056

    Pure volume Boost pedal?

    Agree. Although in my case, I already had a regular volume pedal going from -80dB to 0dB, mostly to set overall volume and do volumes swells, and what you describe above. What I wanted was a 3db or 6db boost pedal for solos. So I added a second "boost" pedal which goes from 0dB to 9dB so I can...
  24. j20056

    Pure volume Boost pedal?

    I used Vol/Pan connected to an expression pedal set to a range of [0db, 9dB]. perfect
  25. j20056

    Pure volume Boost pedal?

    I'd like to insert a volume boost pedal that doesn't add any color to the sound, just adds 3dB or 9dB, whatever setting I store in a channel. I see Drive blocks, but they look more like Distortion pedals and add tone, but I do not see any pure Boost blocks. What is the most CPU friendly way to...
  26. j20056

    Parallel+Series FX chains: volume control issue

    OK so I got it to work via Scenes. I set all FX bypass to Thru and I added a Null Filter at the end of each FX rows 4 and 5. I set the filters to Bypass = Mute and I control the Bypass via Scenes. The cross-fade via Mixer works as prior. This is 100% perfect!!! @Bakerman, I do not know how to...
  27. j20056

    Parallel+Series FX chains: volume control issue

    Focusing on Row4, I set the Bypass to be controlled by my wet/dry mix expression pedal, so that as soon as the pedal is not full heel, then the Delay Bypass is on OFF. I did the same for PlexDly on the same expression pedal. I am using the same because I want just one pedal to control wet/dry...
  28. j20056

    Parallel+Series FX chains: volume control issue

    Thank you. Also removed the reverb in row 2 as it wasn't really needed. CPU down to 67%. Going to try and figure out how to implement your first sentence. It is amazing how great this forum, brand and product and people are. The Eventide forum for the H9000 get 1% of the traffic here.
  29. j20056

    Parallel+Series FX chains: volume control issue

    Thank you. It is ideally the latter as I no vol/pan left. What kind of modifiers are we talking about in your second suggestion? But worst case, I can do your first suggestion. Thank you again.
  30. j20056

    Parallel+Series FX chains: volume control issue

    Thank you. What I want is a way that if both FX in Row4/Row5/Row6 are Bypassed, then there is no dry signal going through either row. However, if one of them is turned On, and the other is Bypassed, then the first one needs to be on. I am unsure how to do that still at this point. The current...
  31. j20056

    Parallel+Series FX chains: volume control issue

    Thank you. I was sort of reluctant to do that, because the preset is a bit complex and I worry you would have to spend a lot of time deciphering what it does especially as there are 5 expression pedals connected to it, External1-4 and Pedal1, with funky cross-fades. Essentially this is a...
  32. j20056

    Parallel+Series FX chains: volume control issue

    how can I show the preset?
  33. j20056

    Parallel+Series FX chains: volume control issue

    Say I have a preset like this: Row1: In1 -> Amp1 -> Cab1 -> Out1 Row2: Cab1 -> FX1 -> FX2 -> Mixer1 ->Out1 Row3: Cab1 -> FX3 -> FX4 -> Mixer1 -> Out1 Essentially I have a dry signal, one parallel loop with two FX in series, and a second...
  34. j20056

    Best way for adding an octave

    My goal is a one octave higher pitch shift on all notes with no scale. From what I see in the Pitch block options, I could use an harmonizer (anything with Diatonic or Chromatic in the name), the virtual capo, or the classic whammy. This is for single note lead with bends so I think that...
  35. j20056

    Wish Virtual Cable Signal Level Meter

    Thanks. I looked and it is great actually, although my question was in Axe-Edit context. My AxeFX is far away from my computer and I cannot really move it to see the front panel of the unit, so any display functionality that doesn't exist in Axe-Edit is sort of "lost" for me.
  36. j20056

    Wish Virtual Cable Signal Level Meter

    I am a former user of the SoundSculpture SwitchBlade. One nice feature in their preset GUI was the ability to click on a virtual cable (connecting two blocks), and have the ability to show the signal level going through that cable on a permanent meter on the GUI display. Such a display would not...
  37. j20056

    Tuner Window Display Triggered via CC?

    Sorry yes, it's about the Axe-Edit III. I haven't been diligent about posting editor issues in the other sub-forum, but you're saying that I should, so I will.
  38. j20056

    Tuner Window Display Triggered via CC?

    I can't seem to find a way other than obviously clicking on the Tuner drop down. The CC trigger only display tuner on the main AxeFX display, which sits in a rack away from my desk. Any alternative other than a DI into a DAW and a tuner window from the DAW?
  39. j20056

    Amp channel switching & effect on/off with AxFx 3 via midi?

    All working. Thank you. Genuinely awesome device the AxeFXIII. I've owned it for 2 weeks now, and I had high expectations, but it goes way beyond.
  40. j20056

    Amp channel switching & effect on/off with AxFx 3 via midi?

    So I got it to work, but I had to connect the MIDI to OUT and not THRU. I always use THRU when I am in a MIDI chain, but the Fractal Audio Wiki page sepcifically says that Thru doesn't send any messages generated by the AxeFX. Going to see if the rest of my MIDI chain is affected, which I...
  41. j20056

    Amp channel switching & effect on/off with AxFx 3 via midi?

    MidiOx crashes Axe-Edit III. But Bome MIDI Translator works. All my devices sending CC messages are seen in the MIDI monityor window but NOT the AxeFXIII. I just have no idea. Is the MIDI Block in the grid supposed to be connected to anything? I have it freely floating right now.
  42. j20056

    Amp channel switching & effect on/off with AxFx 3 via midi?

    Bullets #2 and #3 are wotkjing 100% when I send the MIDI CC's from the Behringer FCB1010. So the conclusion is that the AxeFX MIDI block doesn't send anything, or it sends it in the wrong place. I was just going to ask about a utility to check what MIDI message is actually being sent but you are...
  43. j20056

    Amp channel switching & effect on/off with AxFx 3 via midi?

    Agreed my suggestion was Scene level not block level. meanwhile, other than the MIDI channel in Setup/MIDI/General, what other settings might impact the fact that my MIDI block doesn't work? As mentioned, the Axe responds to MIDI PC changes from my pedal board. I see no other setup controls...
  44. j20056

    Amp channel switching & effect on/off with AxFx 3 via midi?

    I have the same issue with a MarkV:25, also using a VooDoo Control. From what I see, a MIDI block seems to work at the Scene level. So I would setup the correct MIDI messages for a given scene and it should work? But I have a question: How did you get the VooDoo Control to work? I have it in my...
  45. j20056

    How many expression pedals and how youre using them?

    I use 6 of them (studio setup only), in a hybrid tube amp with 4CM and modeled amps with AxeFxIII, in Wet/Dry/Wet configuration. #1 for volume swells, i.e. controls volume level into amp FX loop #2 for cross-fade between real amp+cab and modeled amp for the Dry channel #3 to control the blend of...
  46. j20056

    Multiplexer versus Using Scenes to turn FX on or off?

    say I have this preset: row 1: Phaser row 2: Flanger row 3: In1 -> amp >cab > out1 Lastly, Phaser and Chorus are wired in parallel just before the Amp block. One way to select Phaser versus Flanger is to use a Multiplexer block before the amp and have two scenes that select channel A or B of...
  47. j20056

    Feedback Send as signal splitter?

    Thank you. The only reason I used this approach is because I ran out of rows. I have a complicated preset with 4CM and wet/dry/wet plus an external Eventide processor and one row is also used by the piezo output of my guitar and its own processing. I’m maxed out on rows. My approach works so I...
  48. j20056

    Feedback Send as signal splitter?

    Say I have this preset: In1 > Comp1 > Phaser1 > Flanger1 > Send1 > Out3 Return1 > Amp1 > Cab1 > Out1 The idea is to be able to use the same comp/phaser/flanger chain in front of two amps, respectively a real tube amp connected via Out3, and a modeled amp connected via Return1. I think Send1...
  49. j20056

    Analog Output 2 - not working at all - no clue

    ahahahahah, it wasn't. All the other ones were. Reminds me of John Petrucci's video with Randall Smith testing out the MarkV:25 and no sound... his guitar wasn't plugged. Thank you!
  50. j20056

    Analog Output 2 - not working at all - no clue

    Been using the AF3 for about a week now, using all I/O except #2. Now, as I try to use Output 2, I literally get no signal at all. I carefully set the output to be analog, and I am using XLR to XLR cables to connect to my audio interface. The AF3 works perfectly when sending the main stereo...
  51. j20056

    Relationship between preset and block library - looks like none?

    Say I save Delay1 block in the library as "my_delay_block". Say the delay is set at 400mS. As I do this, the Library dropdown shows "my _delay_block". I save the preset. I then go on and change the delay to 500mS, save the reset, but do NOT resave my_delay_block. I then reload the preset, which...
  52. j20056

    Preset Increment/Decrement Start/End: Cannot do from Current?

    Got it to work, thanks. I think I had the max set at zero, maybe it was the default value, dunno. thanks again. Coming from the arcane and isolated world of the Eventide H9000, it is INCREDIBLY refreshing and encouraging to get an almost immediate response time on this board. That was the second...
  53. j20056

    Preset Increment/Decrement Start/End: Cannot do from Current?

    I do
  54. j20056

    Preset Increment/Decrement Start/End: Cannot do from Current?

    That's the behavior I was expecting, but not what I got. If I have start set at 0 and end set at 512, and say I'm currently on preset 400, then sending the CC MIDI message to increment makes me go to 0001 instead of 401, thence my posting this message.
  55. j20056

    Preset Increment/Decrement Start/End: Cannot do from Current?

    Trying to setup my MIDI pedalboard to allow scrolling through presets by increments/decrements. I found the way to assign a CC for both under MIDI/Remote>>Other. However, there is no option to start from CURRENT, as it seems like you MUST pass an integer number. So is there indeed no way to...
  56. j20056

    Setting Initial Value of Volume Modifier

    Me again. While the above works, it doesn't seem to allow Scene level. When I set the initial values from the AF3 unit, it applies them to all 8 scenes for my preset, and trying to Store scenes with different values doesn't work as the last save override all the other levels. Wondering if this...
  57. j20056

    Setting Initial Value of Volume Modifier

    It appears to be an AxeEdit bug as I found other threads where the same issue is mentioned, since 2020. Apparently, it works when setting the initial value from the AxeFX itself, so going to try that. I can confirm that the initial values can be set from the AxeFX unit itself (a) can be modified...
  58. j20056

    Setting Initial Value of Volume Modifier

    Thank you but this is not what I want. I want the initial value to be 30%, but I want the range to be 0-100
  59. j20056

    PC Reset value... can it be set via Axe-Edit?

    I have the same exact problem, new AxeFX user here. Seems like this issue hasn't been addressed for years.
  60. j20056

    Setting Initial Value of Volume Modifier

    I found this in the user manual: PC Reset sets the value for an external source when a preset first loads. This allows you to override the actual position of an external controller until it is moved or updated. To set the default value: after applying the modifier, exit to the Edit page. Notice...
  61. j20056

    Setting Initial Value of Volume Modifier

    Say I have a Volume modifier block set to control a series of time based blocks like delay. The block is connected to an external expression pedal, and the volume control is set to a parameter range of 0 to 10. Is there a way to specify the initial value of the parameter that would be set when...
  62. j20056

    MarkV power amp only modeling

    That's more or less what I did. I have a volume/pan in the path of my FX return loop of the MarkV and another in the path of the modeled amp. I setup a cross-fade on the two volume controls connected to the same expression pedal. Works well. Modifiers work equally well on Volume/Pan modifiers as...
  63. j20056

    Block from External Device

    Ohhh, I didn't realize that you can use an Input or Output block anywhere in the grid instead of just on the left and right bedges. Well now super easy!!!! cool.
  64. j20056

    Block from External Device

    So I assume you know that Ken Czepelka passed away last September right? He had just released the SwitchBlade ET which finally handled line level signal, and I was all but ready to buy one. Then his tragic passing got me rethinking, and instead, I sold my SwitchBlade GL and bought an AxeFX...
  65. j20056

    MarkV power amp only modeling

    Here is a dumb question though: When getting the preamp signal from the MarkV, do I even need a Power amp, i.e. an AMP blocxk in the AxeFX? Why can't I go from preamp to Cab directly and EQ to match the tone? I mean I only want the pure power amp section, which is not supposed to color that...
  66. j20056

    MarkV power amp only modeling

    Fair analysis EXCEPT... I like to have an expression pedal to do cross-fades between real cab and simulated cab for the dry channel. So my setup is really W/D1/D2/W and I cross-fade D1 and D2 (this is also so that I can use the same config for playing live in the studio versus through headphones...
  67. j20056

    Block from External Device

    I have an Eventide processor and my AF3 stereo In2/Out2 are available. I intend to use them to connect one of the many stereo outputs of the Eventide. However, I would really like to be able to create a new "External Device Block" usable on the grid, and that would be set to get its ins and outs...
  68. j20056

    Constant volume cross-fade

    I was wrong and I can confirm that the Mixer block works fine if located on one of the rows that it modifies.
  69. j20056

    Wish AXE FX III Core - 1U Rack Version

    I got the AxeFXIII for a week now and I can confirm that I never use the front panel other than for setting up devices and hardware connection setups.
  70. j20056

    Constant volume cross-fade

    I’ll try again tonight but the behavior I observed is that if I cross fade rows 2 and 3 and the mixer is in row 3, then I get no volume when setting the expression pedal to play row 2 and mute row 3. Seems logical as the mixer receives row 2, then turns row 3 to zero..: which includes itself...
  71. j20056

    Constant volume cross-fade

    Hummm. Well I had to use a Mixer block because I ran out of Volume/Pan blocks as I needed two cross fades in my preset. Are you sure about the Mixer issue in cross fade context only? Initially I had it at the end of row 3, trying to cross fade rows 2 and 3 but it didn’t work because when setting...
  72. j20056

    Constant volume cross-fade

    To close the loop on this topic; I tried the Mixer block approach and it works. As mentioned above, I can also confirm that the fade is done linearly although there is no option for controlling it. The only negative of a mixer is that for a cross fade, it consumes a row as it needs to sit on a...
  73. j20056

    Constant volume cross-fade

    OK solved. On the main Volume/Pan screen, there is a drop down called Volume Taper, which defaults to Log20A, which is likely right for a straight volume control. By setting both blocks to Linear instead, and keeping the Mid at 50% and a linear 0-100 line, the cross-fade has constant volume...
  74. j20056

    Constant volume cross-fade

    I can't seem to find an obvious way to create these type of Log level graphs with the Edit Modifier of Volume/Pan
  75. j20056

    Constant volume cross-fade

    @GlennO: that doesn't work at all. But remember I am doing 0-100 on one and 100-0 on the other. I tried 70% on one and 30%v on the other but no luck
  76. j20056

    Constant volume cross-fade

    yes the volumes are the same at the extremes. the volume is lowest at the mid point. Thinking volume in dB is Log(acoustic pressure), so maybe sum of x*source1 + (1-x)*source2 is not a constant. I'll fiddle with curves as I don't understand how to use a Mixer block for my use case. Sorry I'm...
  77. j20056

    Constant volume cross-fade

    I have two amps set at the same volume, but different tones although not very different. I assigned a volume block for each, both assigned to External 1, which is an expression pedal. I set the parameter range of the first amp's volume block to min=0, max=10, and vice-versa for the second amp...
  78. j20056

    MarkV power amp only modeling

    Splitting is a good idea, didn't know that was possible. Buys me one mono input. Thing is that I have to model the CabClone (or to your point any good sounding dry tone) from the real MarkV preamp if I want the ability to modulate between my real D1 center dry versus the modeled D2 one. So in...
  79. j20056

    MarkV power amp only modeling

    I am always careful before buying gear to see how vibrant and responsive the user forums are. This forum is just something else and the quality and speed of responses has no equal!!! Thank you. @IronSean: Thank you for a very detailed and thoughtful answer. I actually really like having the real...
  80. j20056

    MarkV power amp only modeling

    My use case is a W/D/W studio rig. Main config is AF3 and a Boogie MarkV:25 head connected via 4CM. The MarkV power amp is connected to a cab as the center Dry channel. My room being too small and reverby ; I cannot mike the cab to feed into the AF3 so I need ro emulate the power amp cab to feed...
  81. j20056

    Somehow arcane MIDI issues

    Sorry meant SPDIF. Got the USB connection as well as I suppose that’s needed for AxEdit to work
  82. j20056

    Somehow arcane MIDI issues

    Got it to work. On #1, using the default AxeFX MIDI ports still receives the MIDI from the FCB1010 connected as described. On #2, I used the standard MIDI (via MIDI Merge adapter) into the MIDI chain and the pedals are now seen by the AxeFX. I do need the AxeFX connected to the FocusRite via...
  83. j20056

    Somehow arcane MIDI issues

    New AxeFX-III user here. I use my AxeFX-III as part of a rig that includes a FocusRite Clarett+8Pre (which also provides a MIDI interface via USB connection to my computer), a Behringer FCB1010 MIDI floorboard and an Eventide H9000R. The AxeFX-III is connected to the MIDI chain via regular MIDI...
  84. j20056

    Purpose of UAS ASIO buffer settings?

    Thank you. So assuming I never use the AF3 as an audio interface, then the FAS ASIO driver is irrelevant? The quick start manual seems to insist that it must be installed. If so, I suppose I should set it to 512 or even 1024 buffers just to make sure it doesn't cripple my CPU even if unused. I'm...
  85. j20056

    Purpose of UAS ASIO buffer settings?

    New AF3 user here, so apologies if trivial. My use case is analog outputs into a Focusrite Clarett+ interface. I am not using the AF3 as the computer interface therefore. In this case, are the settings in the FASUSBAudio relevant at all? Assuming I want to further reduce latency (not that I...
  86. j20056

    Just got AF3. Question about global settings?

    I was talking about the amp and cab OFF global setting. I think I don’t need it. I read the manual about 4CM and it confirms to just not use an amp or cab block.
  87. j20056

    Just got AF3. Question about global settings?

    My use case is studio work with stereo monitors but also a Boogie MarkV:25 which I plan to wire via 4 cable method. I think as long as I do not put any power amps or cabs in the signal chain that goes back to the MarkV power amp, I should be ok right? I do not want to use the global settings as...
  88. j20056

    Wish AXE FX III Core - 1U Rack Version

    This is EXACTLY what the Eventide H9000R is versus the standard H9000. I own the H9000R which has 100% of the functionality via the Emote software, which is Axe Edit equivalent, but also with all controls beyond just presets and grids. The connectivity to computer is via either USB, Wireless or...
  89. j20056

    Can the AxeFX III be 100% controlled by a computer?

    I am ready to take the plunge and buy an AF3. However, my rack is a few feet away from my desk, so I am trying to find out what piece of functionality requires physical interaction with the unit. As a point of reference, I own an Eventide H9000 Rack, which has no physical interface, and I found...
  90. j20056

    Number of Expression Pedals

    I am considering the purchase of an Axe FX III. However, I would need the ability to use 4 expression pedals, and the unit only has two expression inputs from what I see in the manual. However, the manual also mentions "external controllers", and since my additional expression pedals are...
  91. j20056

    Switchblade GL and Windows 7

    I just switched to Win7 from XP, and it doesn't work at all. Cannot poll the Switchblade. Emailed the deveoper. Will see. Did you get it to work somehow?
Back
Top Bottom