Rex
Dignified but Approachable
How do you like it? Did you choose the size because you like it or because it fit?
How do you like it? Did you choose the size because you like it or because it fit?
How's it working out for you?Because it fits.
How's it working out for you?
I'm glad it's not too short for volume, wah and such.The sweep is short, so it's of no use as a Whammy or so.
For other tasks it's okay.
I'm always looking to shave off a pound or two,
That's some snazzy as all get up purple there. Very nice.As of this morning, my most recent MFC setup.
BreadTooth's MFC pedal board with custom painted Mission expression pedals
Just added my Extension unit from Roadrunner this weekend. Has been a nice addition. Current main preset has 8 scenes and 4 amps. 2 amps per scene gradually getting dirtier.
Expression pedals 1. Purple one controls my Roland Gr-55 in my rack for synth and organ type stuff. I used to run the 55 through the FX loop but i've added an onstage monitor so i had to reroute it through Input 1 rear to be able to use output two. I have to have mixer blocks at the front of all my patches to prevent the 55 going through my signal path. You can tie it in with the reverb and looper at the end though so it ends up being pretty cool.
Pedal 2 (blue) - delay mix
Pedal 3 (red) - Boost. I'm just trying this out, but it's assigned to each of the 4 amps Boost function. It's just another way to get a quick solo option etc.
Extension unit : Top - Bottom = Rec, Play, Scene 7, Scene 1. The rec and play option works well, but the play button won't work unless you hold it down. Does anybody have a way for this to continue playing the loop? I don't loop a whole lot, so it's not a big hindrance.
The gaffer's tape has been a great option for me cause i'm a tweaker and the board changes alot. I save the tape if i switch the labels out so they're basically like the stomplabels, but just not as pretty. I'm not too pretty myself so that works out.
Keep on truckin!!!!!!1
The rec and play option works well, but the play button won't work unless you hold it down. Does anybody have a way for this to continue playing the loop? I don't loop a whole lot, so it's not a big hindrance.
Change the specific switch input on the MFC menu to TOGGLE instead of HARDWARE.
That should define the switch to act as a toggle and not momentary (the benefit of using momentary switches – they can set to both by programing).
As of this morning, my most recent MFC setup.
BreadTooth's MFC pedal board with custom painted Mission expression pedals
Pedaltrain Pro
MFC-101 Mark III v3.06
V2 Kicktags
Mission Expression Pedals (3), custom finished in a clear coated metallic candy purple
SP-1 (two output jacks, one for the expression pedal and one for the switch) for Vol / Boost
EP-1 with spring for Wah / Wammy
EP-1 for Rate / Mix
Four (4) right angle TRS cables
30' EtherCon cable
MFC Mark III Layout:
Bank Size = 3
Row 4 : 2 IA switches - Tap/Tuner, MultiDelay
Row 3 : Presets 1-3 in current bank, 2 IA switches - Chorus, Delay
Row 2 : 5 IA switches - Drive, Harmony, Flanger, Phaser, Reverb
Row 1 : scene 1-5
This will most likely change by tomorrow....
heh
That is beautiful and has just raised the bar. Quick question re: your ethercon connection, I am having a real tough time sourcing locally so I am going through Fractal. Have you any thoughts on shielded vs. not. The price differential isnt great so I am leaning toward a 30' Ethercon9-xxx. Anyone else with any advice, its much appreciated.