• We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

    Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Axe-Fx III Firmware 10.0 Public Beta

Status
Not open for further replies.

Fro

Experienced
Hi @FractalAudio. I also got something similar to @Paulinfl. When I switched from my "Your Love" preset to my "Sandman" preset, it freezes and all of the output lights hit red and stay there. It only happened while playing and switching presets. It didn't seem to happen if I wasn't playing while switching presets. The "Your Love" preset has a harmonizer on it, and the "Sandman" preset has a virtual capo, so I thought maybe that was it. But then it occurred to me that my "Sandman" preset is also the only one I have with the Jazz 120 amp in it. I switched back to 9.01 and it seems fine.
 

Attachments

dpeterson

Axe-Master
No lockups here.. seems to sound better. Had one preset that sounded kind of harsh, i reset the amp block and tweaked back now it sounds better, fuller on high end, less harsh.

Thanks again for the tuner updates.
 
Last edited:

bradlake

Axe-Master
So any tube (valve) geeks out here have any suggestions on what amps might most benefit from swapping the new KT77 in?
 

curious

Experienced
Holy crap. Just finished installing 9.1 and reading the update notes when I saw this. Dude! You're a beast!
 

yyz67

Experienced
I have crazy good farts with following Vibroverb settings, especially playing lower notes. Preset attached. I didn't change the Speaker Impedance.

PTM | NFb | TrMa
1.0 | def | 2
0.0 | 0.0 | 5+
0.3 | def | 5+
-0.3 | def | 5+


PTM = Power Tube Mismatch, NFb=Negative Feedback, TrMa = Transformer Match, def = default value
 

Attachments

Last edited:

Warrior

Power User
Switching between scenes in a preset and had a "pop" and input meter on the Axe-FX III and my DAW went to red and stayed there.
No more output after that.

Noticed the same behavior when switching between amp channels.

Youtube would also not play after that unless I unselect Axe-FX III in my aggregate device.

The only way to fix was to reboot the computer.

Here's the preset.
 

Attachments

sb-SG

Member
Hi @FractalAudio. I also got something similar to @Paulinfl. When I switched from my "Your Love" preset to my "Sandman" preset, it freezes and all of the output lights hit red and stay there. It only happened while playing and switching presets. It didn't seem to happen if I wasn't playing while switching presets. The "Your Love" preset has a harmonizer on it, and the "Sandman" preset has a virtual capo, so I thought maybe that was it. But then it occurred to me that my "Sandman" preset is also the only one I have with the Jazz 120 amp in it. I switched back to 9.01 and it seems fine.

So it's the JC120 one more time....
 

peteri

Inspired
Sounds great to me, but getting lots of farts on the JTM45, sounds great on it's own - but hitting the front end with a TS808 and we're in poopy town

Still happy mind, the BF Princeton is simply wonderful
 

xpenno

Power User
This update is awesome! The cab thump is unreal and the top end of the Plexi amps is insane. I WAS totally happy with 9 but damn this is good!
 
Last edited:

peteri

Inspired
One other question - I just can't get a clean sound out of the Jubilee, can't remember if this was better before - but even with input trim on 0.1 and the input gain right down I'm getting breakup (quite a lot)
 
Status
Not open for further replies.
Top Bottom