Yeah, everything still clocking here.These are professional audio interfaces?
I'm using a consumer grade (ie. shitty) Focusrite interface, it didn't lose sync with any prior firmware with external SPDIF clock source.
So.....the good old question....reset amp block?https://www.fractalaudio.com/downlo...xe-fx-3/24p0/axefxiii_dsp_rel_24p00_beta1.zip
Axe-Fx III Firmware Release Notes
24.00
Improved speaker compression and amp interaction modeling.
Changed Master Volume taper for Recto1 models to agree with actual amp. This will slightly reduce the volume into the virtual power amp. Audition presets accordingly.
Added Global MV control to JS410 amp models. Master Volume has been renamed Channel MV. These two master volume controls can be used to balance the tone into the power amp (as in the real amp). The Channel MV decreases the high frequencies as it is turned down whereas the Global MV is transparent.
Added USA MK V Red amp models.
Improved accuracy of USA JP IIC+ models.
Improved accuracy of TX Star models. Global MV controls have been added as the Channel MV in these amps affect the tone (and interacts with the Presence control).
Improved Stack/Hold behavior in Delay block. Note that if the Compander is enabled Stack/Hold is not available and will be disabled.
Improved handling of external word clock. If no clock is present unit will fall back to internal clock until a clock is detected.
Fixed attack behavior of Dynamicomp model to strong input signals. Default attack time also adjusted to match reference pedal.
Fixed wrong PI bias point in Class-A 30W models.
Fixed several mistakes in Div/13 CJ amp models.
Fixed several mistakes in Two Stone J35 models.
Fixed wrong phase inverter bias excursion parameters in Car Ambler model.
Various other fixes and improvements.
Check that your Focusrite clock is the right frequency. If it's 44.1 you'll probably get clicks now because the Axe-Fx will see that the clock is wrong and fall back to internal. But then it'll see that there's a clock and try to lock to external. And back-and-forth once per second.@FractalAudio
On my setup (Focusrite) it doesn't sync with external clock anymore, click... click... click... click. very sad.
Maybe an Auto setting would be a good solution?
Please bring manual mode.
I'm on 48kHz.Check that your Focusrite clock is the right frequency. If it's 44.1 you'll probably get clicks now because the Axe-Fx will see that the clock is wrong and fall back to internal. But then it'll see that there's a clock and try to lock to external. And back-and-forth once per second.
New since when?Can anyone list all new amp types, or the entire list?
New since when?
Axe III day one?
Can anyone list all new amp types, or the entire list?
- USA MK V Red IIC+
- USA MK V Red IIC+ Bright
- USA MK V Red MKIV
- USA MK V Red MKIV Bright
- USA MK V Red XT
- USA MK V Red XT Bright
Try a different cable. I've tested it with a couple different interfaces and everything is working as expected.I'm on 48kHz.
It was (is) rock solid in 23.05.
No. No FAS Stealth, if that's what you are getting at .Thanks.
So 326 types, no new FAS models?
I am using high quality thick shielded cables.Try a different cable. I've tested it with a couple different interfaces and everything is working as expected.
I think that channel has a bright switchWhat is the difference between the Bright models on the Mark V anyone know?
We need Pimp my Recto instalment @2112Let's go is right...now you and Burg have to spend the weekend making new presets!
You guys continue to amaze!https://www.fractalaudio.com/downlo...xe-fx-3/24p0/axefxiii_dsp_rel_24p00_beta1.zip
Axe-Fx III Firmware Release Notes
24.00
Improved speaker compression and amp interaction modeling.
Changed Master Volume taper for Recto1 models to agree with actual amp. This will slightly reduce the volume into the virtual power amp. Audition presets accordingly.
Added Global MV control to JS410 amp models. Master Volume has been renamed Channel MV. These two master volume controls can be used to balance the tone into the power amp (as in the real amp). The Channel MV decreases the high frequencies as it is turned down whereas the Global MV is transparent.
Added USA MK V Red amp models.
Improved accuracy of USA JP IIC+ models.
Improved accuracy of TX Star models. Global MV controls have been added as the Channel MV in these amps affect the tone (and interacts with the Presence control).
Improved Stack/Hold behavior in Delay block. Note that if the Compander is enabled Stack/Hold is not available and will be disabled.
Improved handling of external word clock. If no clock is present unit will fall back to internal clock until a clock is detected.
Fixed attack behavior of Dynamicomp model to strong input signals. Default attack time also adjusted to match reference pedal.
Fixed wrong PI bias point in Class-A 30W models.
Fixed several mistakes in Div/13 CJ amp models.
Fixed several mistakes in Two Stone J35 models.
Fixed wrong phase inverter bias excursion parameters in Car Ambler model.
Various other fixes and improvements.
Also, I don't hear any change in click "rhythm" when switching between INTERNAL and SPDIF/AES IN, it's like it's using the same clock regardless of what setting I choose.I think it sees the clock as reported on the AxeFx screen, but internally it's not syncing to it.