shatteredsquare
Power User
It happens only if Axe Edit is open.
No way
It happens only if Axe Edit is open.
I just upgraded to 12.01 and using Axe Edit 1.04.02 RC 1 I found an issue. I am not sure if it's from Axe Edit or the new 12.01 firmware. And yes I did refresh everything.
I have a preset with a Friedman HBE in channel A. It had been saved last night with 12.00 with the input boost on, but it was off now. I re-saved it with the input boost on, then started going through the other blocks. Switching to the stereo tape block and back to the amp block turns off the input boost on the amp. I can turn it back on and re-save it, but every time I switch to the stereo tape delay block and come back to the amp block it has turned off the input boost. I tried it a half dozen times, with the same result.
It is only happening with the amp in channel A.
I just checked and it is doing this on every preset. Every amp in channel A has turned off the input boost, that I had saved as on previously.
Edit: I just switched back to 12.00 and the above issue is not happening. So it appears to be the 12.01 firmware.
Try this on the front panel, with AE closed. Does it still occur?
I already reverted back to 12.00. It works fine from the front panel or Axe Edit on 12.00.
The issue is not happening on 12.00, so it was likely the 12.01 firmware.
No way
It's also possible that AE (which is not yet fully compatible with 12.00 and 12.01) is the cause, if you were using AE and not the front panel.
These new phasers are so beautiful. Making practice a little easier tonight when it sounds like this, that's for certain.
When I open Axe-Edit my preset tone is spoiled. I close Axe-Edit, re-select the preset, and it is OK.
I cannot use Axe-Edit
Edit: I've noted what happens. When I open Axe-Edit, the parameters of the AMP block change. It seems like if the block was reset. All tone controls to noon
The same is happening for me. I'm on AE 1.04.02 RC 1 and Fw 12.01When I open Axe-Edit my preset tone is spoiled. I close Axe-Edit, re-select the preset, and it is OK.
I cannot use Axe-Edit
Edit: I've noted what happens. When I open Axe-Edit, the parameters of the AMP block change. It seems like if the block was reset. All tone controls to noon
Hi,It may or may not already be in there.
behavior confirmed here....BMT goes to noon on any preset selected in AxeEdit....I Do not envy @Michael Pickens and the dev crew when the boss goes on an extended eCliffany™ run.......When I open Axe-Edit my preset tone is spoiled. I close Axe-Edit, re-select the preset, and it is OK.
I cannot use Axe-Edit
Edit: I've noted what happens. When I open Axe-Edit, the parameters of the AMP block change. It seems like if the block was reset. All tone controls to noon
Has already been answered : needs an AxeEdit update...Running into another glitch. The OD250 Drive is not listing the Basic function but has the options for Drive and Tone , and when clicking on the other options(Tone/Graphic EQ), I lose the ability to choose the Basic feature again. Not sure if this has been reported or not? I have the current version of Axe Edit III as well.
Repeat:
I will not use Axe-Edit with firmware 12.01, until its update is released.
I will not use Axe-Edit with firmware 12.01, until its update is released.
I will not use Axe-Edit with firmware 12.01, until its update is released.
I will not use Axe-Edit with firmware 12.01, until its update is released.
etc.
Hilarious!!!