• We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

    Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

FracTool - ultimate multitool for FAS devices

sidsin

Inspired
Thanks!, so there is no way to work around those tones?

Also, these tones involve tone matching. That could also be the reason?
 

yek

Moderator
Moderator
Hi Alex,
I'm using Batch Setter with function set to "Just resave".
When I edit the field "Apply to presets", the cursor stays in that field after pressing Enter, and the button "Apply" is not operational.

There's no problem when I just leave that field at its default setting (0-511).
 

AlGrenadine

Axe-Master
Vendor
Hi Alex,
I'm using Batch Setter with function set to "Just resave".
When I edit the field "Apply to presets", the cursor stays in that field after pressing Enter, and the button "Apply" is not operational.

There's no problem when I just leave that field at its default setting (0-511).
Hey Alex, Thanks checking this right now :)
 

AlGrenadine

Axe-Master
Vendor
I think I figured out what is going on with the pitch block arpeggiator.

FracTool shows the steps in this order: Step 1, 10, 11, 12, 13, 14, 15, 16, 2, 3, 4, 5, 6, 7, 8, 9. When it converts the block it coverts step 1 like it should be, but it converts the values for step 10 as if it were step 2, step 11 as if it were step 3, (and so on) step 12 as step 4, step 13 as step 5, step 14 as step 6, step 15 as step 7, step 16 as step 8.

The conversion comes out as:
Step 1= 3
Step 2 = 24 (when it should have been 0)
Step 3 = 24 (when it should have been 3)
Step 4 = 24 (when it should have been 4)
Step 5 = 24 (when it should have been 5)
Step 6 = 24 (when it should have been 4)
Step 7 = 24 (when it should have been 0)
Step 8 = 24 (when it should have been 0)
etc.

Here is a screen shot of the pitch block arpeggiator section one of Simeon synth presets I converted.

I've already corrected the few presets I needed to by hand so I am good. I just thought this info might help you.


View attachment 59708
Ok found the bug, a lot of conversions will work better now :)
 

AlGrenadine

Axe-Master
Vendor
Hi Alex,
I'm using Batch Setter with function set to "Just resave".
When I edit the field "Apply to presets", the cursor stays in that field after pressing Enter, and the button "Apply" is not operational.

There's no problem when I just leave that field at its default setting (0-511).
FracTool 3.38 is available :
- Supports AxeFx III firmware 11 beta 1
- Fixes Apply button in batch setter
- Fixes synth arpeggios conversion issues when converting from II to III
 

trancegodz

Power User
I have not tried the batch setter yet. Is it possible with the batch setter to change the cab block for a group of presets?
If so, who do you do it? I have a bunch of presets I'd like to have the same cab block.
 

trancegodz

Power User
The cab slot you mean? Yes
I created a master cab block with my favourite 16 cab blocks in it. Channel A = 4x12 cabs for Marshalls & Freedman's, Channel B = cabs for Fender amps, Channel C = cabs for Vox, Matchless, and Morgan amps, and Channel D = Misc others.

I was wondering if I could use batch setter to load in this whole master cab block to a group of presets at a time. I've never used batch setter and don't really know what it can and can not do.
 

AlGrenadine

Axe-Master
Vendor
I created a master cab block with my favourite 16 cab blocks in it. Channel A = 4x12 cabs for Marshalls & Freedman's, Channel B = cabs for Fender amps, Channel C = cabs for Vox, Matchless, and Morgan amps, and Channel D = Misc others.

I was wondering if I could use batch setter to load in this whole master cab block to a group of presets at a time. I've never used batch setter and don't really know what it can and can not do.
No, it's a setter, not a block putter ^^
 

jclemensfl

Inspired
@AlGrenadine
Al, I apologize for the basic question.
My goal is to transfer all of my presets and cabs from my AX8 to the AxeFxIII. However, I have to relinquish the AX8 before the the FXIII arrives.
Do I just need to backup the AX8 thru FracTool into the three basic files (System, All-Preset-Banks, All-Cabs-Banks) and then I will be able to just drop the Preset and Cab banks all at once into the FxIII? Or do I have to do something more nuanced?
Just don't want to get my FXIII and realize I didn't get the correct files from my (already gone) AX8.
 

AlGrenadine

Axe-Master
Vendor
@AlGrenadine
Al, I apologize for the basic question.
My goal is to transfer all of my presets and cabs from my AX8 to the AxeFxIII. However, I have to relinquish the AX8 before the the FXIII arrives.
Do I just need to backup the AX8 thru FracTool into the three basic files (System, All-Preset-Banks, All-Cabs-Banks) and then I will be able to just drop the Preset and Cab banks all at once into the FxIII? Or do I have to do something more nuanced?
Just don't want to get my FXIII and realize I didn't get the correct files from my (already gone) AX8.
You need a whole backup with Fractal Bot
 

Surefire641

Member
After downloading the latest update (Ver 3.38) and using with Axe Edit III version 1.03.10, I cannot get any presets to send to the Axe III. The preset just shows all blank blocks, irrespective of what preset I'm trying to send (XL+, AX8, etc). Any workaround for this?Screen Shot 2019-11-21 at 13.27.36 PM.png
 

Stratopack

New Member
Hey there - just got my AxeFx III and want to convert all of my AX8 Band presets. I think FracTool is the perfect way to go :)
How can I convert custom scales for the Harmonizer? This is not automatically done, right? What about user cabs? Are they converted automatically?
Thanks for your help
 
Top Bottom