You know what ol’ Jack Burton says about that...
WOOT! It’s about goddanged time someone notices that! You should get a free shirt. Maybe the white muscle shirt with Fu Manchu on the front... thank you for noticing!
Best. Movie. Ever.
You know what ol’ Jack Burton says about that...
WOOT! It’s about goddanged time someone notices that! You should get a free shirt. Maybe the white muscle shirt with Fu Manchu on the front... thank you for noticing!
Best. Movie. Ever.
Thanks for confirming. This is what I assumed based on the release notes.No, each block has wet signal and dry signal. For example in a delay the dry goes from the input to the output and gets added to the wet. Before both would mute. Now only the wet mutes. This allows the dry to continue uninterrupted while the wet gets muted, the various parameters get updated and then the wet unmuted.
Are you using Axe Edit or the front panel?I'm using ODS 100 clean and I cant seem to select Grinder on the input boost ....anyone else? just wont let me select it keeps going to shimmer...cant select super OD either
AXE editAre you using Axe Edit or the front panel?
I'm using ODS 100 clean and I cant seem to select Grinder on the input boost ....anyone else? just wont let me select it keeps going to shimmer...cant select super OD either
Nothing wrong, but the IR is indeed terrible in combination with the Solo amp model.
What are you using to monitor the III with?
don`t wait, fixed the cathode follower in the AXEIII'm just about ready for a release version but waiting for feedback on the improved scene switching.
Axe-Fx III Firmware Release Notes
5.00
Completely new Amp block cathode follower algorithm yielding more accurate results. The “Ideal” cathode follower type is no longer supported as it is incompatible and has been removed from the GUI. The Cathode Follower Time and Ratio parameters have also been removed as they are no longer applicable. A “Grid Clipping” parameter has been added which allows the user to adjust the grid clipping in the cathode follower. The default value reflects the “softer” response of classic British and American tubes like Mullard, Sylvania and RCA. Higher values simulate the response of modern Chinese and Russian tubes with more abrupt clipping.
Updated various Amp block parameters related to new cathode follower algorithm. Existing presets are automatically updated to the new values.
Added AES/SPDIF Input Level control. This is located in the I/O->USB/AES menu. NOTE: this parameter will default to -40 dB after installation of the firmware. Be sure to adjust to the desired level if using the AES or SPDIF inputs.
Added Treble Booster and Mid Booster boost types to Amp block.
Improved Scene/Channel change logic. Only the wet data is muted when changing scenes and channels now leaving the dry data intact which results in smoother transitions.
Fixed wrong bass pot taper in Friedman Small Box model.
Fix FC per-preset corruption with some presets.
that was it..thanksYou haven't refreshed Axe-Edit's definitions.
I'm still hearing artifacts when using the presence control - once you cross 2 or so.
For example, in USA Clean (see patch) - it's just amp straight to an output block.
These are the artifacts I'm hearing as I turn presence from 2 -> 0 -> 2
That Tone of Kings. Man, so good.
First half is without, second half is with. There's cascading drive blocks. The preset is normally: Micro Boost > '65 Bassguy Bass, so when the ToK is kicked on it's ToK > Micro Boost > '65 Bassguy Bass.
The preset is built around an @austinbuddy preset pack setting. Sounds so good with Strats.
View attachment 53523
That Tone of Kings. Man, so good.
First half is without, second half is with. There's cascading drive blocks. The preset is normally: Micro Boost > '65 Bassguy Bass, so when the ToK is kicked on it's ToK > Micro Boost > '65 Bassguy Bass.
The preset is built around an @austinbuddy preset pack setting. Sounds so good with Strats.
View attachment 53523
That Tone of Kings. Man, so good.
First half is without, second half is with. There's cascading drive blocks. The preset is normally: Micro Boost > '65 Bassguy Bass, so when the ToK is kicked on it's ToK > Micro Boost > '65 Bassguy Bass.
The preset is built around an @austinbuddy preset pack setting. Sounds so good with Strats.
View attachment 53523