Hello all,
I feel like I've scoured the internet for an answer and though I found many to get me to where I am now with my setup, there is one lingering problem I can't seem to figure out. Here is my setup and settings:
Axe-FX - Quantum 1.01 (newest)
Saffire Pro Mix control - 3.6 (newest)
Logic Pro X (newest, but not open during these tests)
Axe-FX SPDIF IN to Pro 40 OUT, Axe-FX SPDIF OUT to Pro 40 IN
Pro 40 out to QSC K12's L & R
PRS CE22 plugged directly into INSTR on front panel of Axe-FX
AXE-FX is connected to USB of iMac (I've tested with the USB disconnected, no change)
Pro 40 is connected to Firewire of iMac
Axe-FX settings:
Main input source - Analog (In 1)
World Clock - Auto
SPDIF/AES - SPDIF
Pro 40 Mix Control settings:
Sample Rate - 48 kHz
Sync Source - SPDIF
The issue seems to be intermittent. The Sync Status will go from "Locked" to "No Lock" causing an annoying popping sound to come from the monitors.
When I first turned the system on yesterday, the problem didn't seem to be there. When I turned it on today, it was happening almost uncontrollably. As I fiddled with settings, jumping back and forth, it seemed to calm down only happening when I muted the strings on the guitar. As I type this, the guitar sits on the stand with the volume all the way up and every so often it'll switch from Lock to No Lock giving off the popping. I then lower the volume to 0 on the guitar and the Lock to No Lock becomes more apparent. I will note that as the pop is occurring the volume level bar in the mix control peaks to red as well.
I'm not sure what else I can do to stop this from happening. It's just annoying at this point.
I appreciate any help you all can offer.
Thank you,
Jerry
I feel like I've scoured the internet for an answer and though I found many to get me to where I am now with my setup, there is one lingering problem I can't seem to figure out. Here is my setup and settings:
Axe-FX - Quantum 1.01 (newest)
Saffire Pro Mix control - 3.6 (newest)
Logic Pro X (newest, but not open during these tests)
Axe-FX SPDIF IN to Pro 40 OUT, Axe-FX SPDIF OUT to Pro 40 IN
Pro 40 out to QSC K12's L & R
PRS CE22 plugged directly into INSTR on front panel of Axe-FX
AXE-FX is connected to USB of iMac (I've tested with the USB disconnected, no change)
Pro 40 is connected to Firewire of iMac
Axe-FX settings:
Main input source - Analog (In 1)
World Clock - Auto
SPDIF/AES - SPDIF
Pro 40 Mix Control settings:
Sample Rate - 48 kHz
Sync Source - SPDIF
The issue seems to be intermittent. The Sync Status will go from "Locked" to "No Lock" causing an annoying popping sound to come from the monitors.
When I first turned the system on yesterday, the problem didn't seem to be there. When I turned it on today, it was happening almost uncontrollably. As I fiddled with settings, jumping back and forth, it seemed to calm down only happening when I muted the strings on the guitar. As I type this, the guitar sits on the stand with the volume all the way up and every so often it'll switch from Lock to No Lock giving off the popping. I then lower the volume to 0 on the guitar and the Lock to No Lock becomes more apparent. I will note that as the pop is occurring the volume level bar in the mix control peaks to red as well.
I'm not sure what else I can do to stop this from happening. It's just annoying at this point.
I appreciate any help you all can offer.
Thank you,
Jerry