I understand your question TF.
I've been spending all weekend trying to make the 1010 work as I want it to, but I'm nowhere close :-(
I want it to change scenes, and it does.....but the leds are all messed up. And that's what you're asking, right? Is there a way to have the 1010 show that you are on scene...3, and that is the only led lit.
Apart from that, tap tempo is also a weird one.
I think I've given up now and pull up the old pod....
Ken
I'm not quite sure I understand what you are asking, but if you have midi controller connected to the Axe Fx while Axe Edit is also connected and then change scenes, Axe Edit will reflect those changes.
I do it all the time.
Sent from my iPhone using Tapatalk
Hey guys,
Sort of. Say I have preset 1 selected, which defaults to scene 1. When I press stomp 7 on the FCB, it should move to scene 2, which is does. However, it does not change to scene 2 on Axe Edit. I haven't had a chance to try 3.1.1 but maybe that will fix it. I'm hoping that the guys who posted above are mistaken, but if not, it doesn't look so good!
Thanks!
What CC# is that switch/button set to on the FCB?
First time :Ch.01 | CtrlChange 026 127
Second time Ch.01 | CtrlChange 026 127
how did you determine those were the values to be set?
Do you mean how I read them? That's via FCBControlCenter.
As for setting them, I'm not entirely sure to be honest. A bit embarrassed, as I think if I remember correctly I had loaded up someone's .syx that seemed to be working how I wanted it to. Next thing I know college mid terms come up, I get stuck scoring a friends film, and I pick up the Axe again and notice this problem.
EDIT: Yep.. Drive Block on/off is set to 26 right now on my Axe.
Even still, is there a way to make the drive block show it's current state on Axe Edit? I guess this still goes back to my original question a bit.
Do you mean how I read them? That's via FCBControlCenter.
As for setting them, I'm not entirely sure to be honest. A bit embarrassed, as I think if I remember correctly I had loaded up someone's .syx that seemed to be working how I wanted it to. Next thing I know college mid terms come up, I get stuck scoring a friends film, and I pick up the Axe again and notice this problem.
EDIT: Yep.. Drive Block on/off is set to 26 right now on my Axe.
Even still, is there a way to make the drive block show it's current state on Axe Edit? I guess this still goes back to my original question a bit.
nothing to be embarrassed about. i just wanted to confirm that you didn't think 26 was scenes or read that somewhere.
yes, if you want that switch to change to a Scene, you need to change the CC number from 26 to 34, and then give that switch a particular value like 0, for Scene 1, 1 for Scene 2, etc. this is all in the Scenes mini-manual available on the Fractal support website.
i highly recommend keeping the Axe-Fx Control menu set to default values and change the FCB instead. so don't change 26 to 34 on the axe; it will cause a ton of problems later and make it very hard to troubleshoot.
as for the Drive turning on in Axe-Edit, again, Axe-Edit is intended to be the "master" controller and midi commands sent to the Axe-Fx via footswitch or other unit won't update Axe-Edit.
Scenes might actually change in Axe-Edit since that is a bigger operation than a block engage/bypass.
Have you actually confirmed that?
http://forum.fractalaudio.com/mfc-discussion/83986-mfc-101-axe-edit-not-talking.html
http://forum.fractalaudio.com/axe-e...edit-track-real-time-changes.html#post1015776
http://forum.fractalaudio.com/axe-fx-ii-discussion/51018-axe-fx-ii-totalsync.html#post657519
http://forum.fractalaudio.com/axe-edit-general-discussion/77485-axe-edit-mfc-bypass-states.html