Francesco Fiorentini
Member
Waiting for the final release
My entire morning has been a combination of
Coffee
AC20
Stratocaster
AC30
Coffee
Stratocaster
SO DAMNED GOOD !
Sounds great. Which Austin preset did you start with.
I essentially never run out of CPU now. Everything I want is in one preset and then some. My only problem now is I lose track of channels on blocks and what they do. I've tried to apply some logic to things like the drive blocks, but it can be hard to keep track of in the moment.Love that this preset is only at 80% CPU
I've been using my AX8 for rehearsals and am looking forward to getting my power amps / cabs out of storage so I can use the III and get some more elbow room!
I hope you actually connect your strat to the axe and not do your things seperate
Yup. A preset can do so much that it's hard to keep track of everything you put into it. That's driven me away from kitchen-sink presets. If I can't name it with a scene, it goes into another preset. Named channels would be a boon.View attachment 53535
I essentially never run out of CPU now. Everything I want is in one preset and then some. My only problem now is I lose track of channels on blocks and what they do. I've tried to apply some logic to things like the drive blocks, but it can be hard to keep track of in the moment.
it doesn't read it every single time. always good to do Refresh after FW Update when you update firmware.I did not know this about beta versions, I don’t recall seeing anything about beta firmware update procedures being different in the manual.
However, I’m pretty sure Axe Edit read through block definitions on every beta that I’ve loaded.
This.it doesn't read it every single time. always good to do Refresh after FW Update when you update firmware.
beta procedures are not in the manual because it's beta.
View attachment 53535
I essentially never run out of CPU now. Everything I want is in one preset and then some. My only problem now is I lose track of channels on blocks and what they do. I've tried to apply some logic to things like the drive blocks, but it can be hard to keep track of in the moment.
Yes and even if internal version has a flag for beta it doesn't report beta number to editorThis.
Going from one 5.00 beta to another beta doesn't register as new firmware, because it's still 5.00.
+0.5 this wish? Seeing them listed as "Channel A", etc. doesn't help with my recall. I still need to call up the channel to remember that I set Channel C on drive block 3 to be a Pi Fuzz, for example. Named channels are really where I'd like to see things go.This is why my WISH was to be able to click on the channels tab - in Edit , and see a list , without having to select each channel.
That Tone of Kings. Man, so good.
First half is without, second half is with. There's cascading drive blocks. The preset is normally: Micro Boost > '65 Bassguy Bass, so when the ToK is kicked on it's ToK > Micro Boost > '65 Bassguy Bass.
The preset is built around an @austinbuddy preset pack setting. Sounds so good with Strats.
Thank you! You absolutely will not regret an @austinbuddy preset pack purchase. Money well spent.Awesome tone AND chops Ian!
Also, I'm starting to realise that every single time I'm going to hear a recording from an @austinbuddy preset that I'm going to love it! Might have to convince the wife on a purchase of that....
Thank you! You absolutely will not regret an @austinbuddy preset pack purchase. Money well spent.
(Buddy doesn't pay me to say these things. I wouldn't use them if I didn't like them. )
Worth every penny.Completely agreed. @austinbuddy presets are outstanding. Many of them I’ve left exactly as they are and many of them I’ve tweaked to my tastes.
Seriously money well spent.
I had your same issue. I reinstalled the previous beta, then re-installed this beta,reset my amps, poopy bass gone.I just quickly created the patch from scratch and randomly picked an IR. I was trying to demonstrate the Class-A amp level differences, but if Cliff says that is normal, then OK. It seems that when I added a Class-A to the B channel on an existing preset, it sounded way worse. I suspected I tweaked something. When I reset the channel the only thing that changed was the Speaker Compression. It was 3.0 on my existing preset. Resetting the channel with the "Class-A 30W Hot" changed it to 1.0. That brought the level up a bit.
I don't recall changing Speaker Compression. I may have started with a copy of a factory preset that had it set.
I'm currently in an apartment waiting for our home remodel to finish (just weeks away!). I monitor on Adam A7 or Beyerdynamic DT 770 Pro Headphones. In a few weeks, it will be ATC SCM 100s
EDIT: I consider this case-closed at this point. Thanks to all that looked into it. Now, off to antique shopping... I'd rather be playing my guitar...
+0.5 this wish? Seeing them listed as "Channel A", etc. doesn't help with my recall. I still need to call up the channel to remember that I set Channel C on drive block 3 to be a Pi Fuzz, for example. Named channels are really where I'd like to see things go.
Now I don't know that I should bother with the beta and just wait for it.
That Tone of Kings. Man, so good.
First half is without, second half is with. There's cascading drive blocks. The preset is normally: Micro Boost > '65 Bassguy Bass, so when the ToK is kicked on it's ToK > Micro Boost > '65 Bassguy Bass.
The preset is built around an @austinbuddy preset pack setting. Sounds so good with Strats.
View attachment 53523