STD + Art SLA2 + Mesa 2x12 cab + Akg wireless

MPZ

MPZ

Member
Hi I have an Xae FX STD + Art SLA2 + Mesa 2x12 cab + Akg wireless.
I adjust the input volume at 75% (when orange led flashes playing hard) and use the rear input (wireless volume at 50%), i think that the level configurations is correct.
Have anyone good distortioned preset for similar configuration?
 
I always use the front input..it sounds better due to its "Special Sauce"

What do you feel that you are missing?
 
nixerx said:
I always use the front input..it sounds better due to its "Special Sauce"

What do you feel that you are missing?
Click to expand...

I can't get good distorted sound, low punch and some noise.
I've tried varios guitars and rear and front input.
I think thats the problem is the configuration?? From Axe out to SLA2 with mono jack cable (SLA2 is configured with bridge mode).
 
pepitovadecurt said:
I can't get good distorted sound, low punch and some noise.
I've tried varios guitars and rear and front input.
I think thats the problem is the configuration?? From Axe out to SLA2 with mono jack cable (SLA2 is configured with bridge mode).
Click to expand...

Im running the Ultra -> SLA2->Cab or PA
Ill say ive had some issue getting the rumble but if you add a couple of DB in the Global EQ @ 120 it will help. Drop some of the 8k to remove some ice pick. Set the Speaker resonance to 110 or 120 under the amps advance tab.. it takes a bit of time to learn the tricks but you will nail them.
 
nixerx said:
Im running the Ultra -> SLA2->Cab or PA
Ill say ive had some issue getting the rumble but if you add a couple of DB in the Global EQ @ 120 it will help. Drop some of the 8k to remove some ice pick. Set the Speaker resonance to 110 or 120 under the amps advance tab.. it takes a bit of time to learn the tricks but you will nail them.
Click to expand...

Thank's Nixerx, i've tried it and the sound is more better!
I'm preparing a lot of presets for upload to this forum.
 
Last edited:
I still do not get good presets for metal.
Following the recommendations of Nixerx sounds better but not quite right.
Anyone have any preset to this configuration?
 
(matrix PA, 2x12 with V30s, passive pickups, front input)

Uberschall

bias, hi freq res, pres freq and presence = full

tone freq 610, location end, type active + active pres

spkr res 106, low freq res 6.5, thump 8.5

b+ cap 8.5, drive 5, bass 5.5, mid -3, treb 9, master 8.5, bright on


Right after the amp

Low pass filter, 12K

Notch filter, 9.8K , Q 2.3
 
Last edited:
speedloader said:
(matrix PA, 2x12 with V30s, passive pickups, front input)

Uberschall

bias, hi freq res, pres freq and presence = full

tone freq 610, location end, type active + active pres

spkr res 106, low freq res 6.5, thump 8.5

b+ cap 8.5, drive 5, bass 5.5, mid -3, treb 9, master 8.5, bright on


Right after the amp

Low pass filter, 12K

Notch filter, 9.8K , Q 2.3
Click to expand...


You use the Power Simulation? What's the best option to use with power amp and guitar cab?
Thanks.
 
Yesterday I tried the settings and sounds really good just by adding a compressor before the amp.
It has plenty of background noise, how I can remove it?
 
Really depends on your guitars, I use the gateexp block before the amp with both low and hi cuts at 1Kz and threshold at -80db

You use the Power Simulation? What's the best option to use with power amp and guitar cab?
Click to expand...

Imo, the PA sim is essential to add dynamic to higain tones (hence the unusual settings)
 
You must log in or register to reply here.
Back
Top Bottom