J
joe rogers
Guest
The FX8 V3.50 is now available for download. Some really cool new features, as well as some bug fixes. As always, please read the release notes before installing. We always advise you to back up your FX8 before installing new firmware with Fractal-Bot.
Here are the Links to download (please take care to download the correct firmware):
FX8 Original
FX8 Mark II
Additionally, there is a new version of FX8-Edit to support the new changes:
FX8-Edit V1.4.0
Release Notes:
FX8 V3.50 introduces some cool new features as well as a couple of bug fixes.
Additions:
· Added new “Control Switch Blocks” CS1 and CS2 – NOTE: see instructions below
· Added new GLOBAL and PER-PRESET momentary switches – NOTE: see instructions below
· Added the BANK LIMIT feature – NOTE: see instructions below
Fixes:
· Fixed a bug that prevented Pedals from driving controllers other than External.
· Fixed Recall Effect; bug was preventing loading effects from older presets.
· Corrected the behavior of Scene footswitches on preset load.
GLOBAL and PER-PRESET Momentary Footswitches
Momentary switches do not “latch” when you step on them. They activate while your foot is down on the switch, and deactivate when you lift it up. Any of the numbered footswitches of the FX8 may now be designated as MOMENTARY.
This can be done either GLOBALLY, or PER-PRESET.
If a momentary footswitch is used to BYPASS/ENGAGE effects, the effect state will be reversed by the action of the switch.
A block that is saved as ENABLED will by momentarily bypassed. A block that is saved as BYPASSED will by momentarily enabled. The same is true for a momentary footswitch assigned to SCENE 1/2 Toggle: depending on whether Scene 1 or Scene 2 is selected, the switch will momentarily toggle to the other.
1. To Set Up a Global Momentary Switch
a. Navigate to the GLOBAL FOOTSWITCH (“GBL FS”) page of the GLOBAL menu under SETUP.
b. Set each switch as desired to one of the following options:
i. PER-PRESET
ii. GLOBAL LATCHING (This is equivalent to the “GLOBAL” setting from older firmware versions).
iii. GLOBAL MOMENTARY
2. To Set Up a Per-Preset Momentary Switch
a. First, call up the preset you want to edit footswitches for.
b. From the main FOOTSWITCH (“FS”) page of the FX8, page right to the MISC page.
c. Select the new FOOTSWITCH MODE (“FS MODE”) option and press <ENTER>
d. Set Each footswitch as desired:
i. LATCHING
ii. MOMENTARY
e. Save the preset! (STORE -> ENTER -> ENTER)
NOTE: The settings on the FS MODE page have no effect for a footswitch if it is set to one of the GLOBAL options on the GBL FS page!
Controller Footswitch Blocks CS1 and CS2
The FX8 now has the ability for footswitches 1-8 to operate as “Control Switches”.
Control Switch 1 and Control Switch 2 now appear in the list of SOURCES on every MODIFIER page.
Using this feature, for example, you can create a BOOST footswitch (Volume Modifier) a WHAMMY effect (Pitch Block: Control Modifier) or a single footswitch that toggles two or more effects on or off in unison (BYPASS MODE modifiers).
CONTROL SWITCH 1 and 2 are footswitch blocks that can be assigned Globally or Per-Preset like any other Footswitch Block from the main Footswitch (“FS”) page. Use NAV to select the desired location and turn “VALUE” to step through the list of available footswitch assignments.
To Set Up a Control Switch Footswitch:
1. On the Footswitch (“FS”) page of the FX8, use NAV and VALUE knobs to assign CS1 or CS2 to footswitch 1 – 8
2. Add a modifier to the desired parameter, setting “CTRL SW1” or "CTRL SW2” as the SOURCE.
3. Adjust the modifier to work as desired.
Now, when you step on the footswitch, the modifier will change the value of the assigned parameter.
NOTE: Coupled with the new “Momentary Footswitch” options, Control Switches are quite powerful!
The initial value of each Control Switch is saved per scene. The initial values are set on the new Control Switches (“CTRL SW”) page of the CONTROLLERS area of the MISC page.
To Set Initial Values for a Control Switch:
1. From the main FOOTSWITCH (“FS”) page of the FX8, page right to the MISC page.
2. Select the CONTROLLERS option and press <ENTER>
3. Page to the CONTROL SWITCH (“CTRL SW”) page.
4. Set the initial value of each switch for each scene to either “ON” or “OFF”.
Bank Limit
Bank Limit is a new feature designed to prevent “oops” when stepping up or down through banks during a live performance.
It limits the available banks you can access through the footswitches with an UPPER and LOWER limit. For example, you could limit your FX8 to footswitch access to banks A through D for one gig, and banks L and M for another. Bank Limit is enabled through the global menu, and adds three new parameters to the GLOBAL SETTINGS menu.
To set up Bank Limit:
1. Navigate to the SETTINGS page of the GLOBAL menu under SETUP.
2. Set BANK LIMIT as desired: “NO”, “WRAP”, & “NO WRAP”
a. NO – Banks are NOT limited. Lower and Upper limit settings are IGNORED.
b. WRAP – Banks ARE limited and will wrap around from the highest back to the lowest (or vice versa).
c. NO WRAP – Banks ARE limited and will NOT wrap.
3. Set BANK LOWER LIMIT: A – P as desired. Cannot be higher than the UPPER limit.
4. Set BANK UPPER LIMIT: A – P as desired. Cannot be lower than the lower limit.
This feature has no effect on FX8 Edit.
Here are the Links to download (please take care to download the correct firmware):
FX8 Original
FX8 Mark II
Additionally, there is a new version of FX8-Edit to support the new changes:
FX8-Edit V1.4.0
Release Notes:
FX8 V3.50 introduces some cool new features as well as a couple of bug fixes.
Additions:
· Added new “Control Switch Blocks” CS1 and CS2 – NOTE: see instructions below
· Added new GLOBAL and PER-PRESET momentary switches – NOTE: see instructions below
· Added the BANK LIMIT feature – NOTE: see instructions below
Fixes:
· Fixed a bug that prevented Pedals from driving controllers other than External.
· Fixed Recall Effect; bug was preventing loading effects from older presets.
· Corrected the behavior of Scene footswitches on preset load.
GLOBAL and PER-PRESET Momentary Footswitches
Momentary switches do not “latch” when you step on them. They activate while your foot is down on the switch, and deactivate when you lift it up. Any of the numbered footswitches of the FX8 may now be designated as MOMENTARY.
This can be done either GLOBALLY, or PER-PRESET.
If a momentary footswitch is used to BYPASS/ENGAGE effects, the effect state will be reversed by the action of the switch.
A block that is saved as ENABLED will by momentarily bypassed. A block that is saved as BYPASSED will by momentarily enabled. The same is true for a momentary footswitch assigned to SCENE 1/2 Toggle: depending on whether Scene 1 or Scene 2 is selected, the switch will momentarily toggle to the other.
1. To Set Up a Global Momentary Switch
a. Navigate to the GLOBAL FOOTSWITCH (“GBL FS”) page of the GLOBAL menu under SETUP.
b. Set each switch as desired to one of the following options:
i. PER-PRESET
ii. GLOBAL LATCHING (This is equivalent to the “GLOBAL” setting from older firmware versions).
iii. GLOBAL MOMENTARY
2. To Set Up a Per-Preset Momentary Switch
a. First, call up the preset you want to edit footswitches for.
b. From the main FOOTSWITCH (“FS”) page of the FX8, page right to the MISC page.
c. Select the new FOOTSWITCH MODE (“FS MODE”) option and press <ENTER>
d. Set Each footswitch as desired:
i. LATCHING
ii. MOMENTARY
e. Save the preset! (STORE -> ENTER -> ENTER)
NOTE: The settings on the FS MODE page have no effect for a footswitch if it is set to one of the GLOBAL options on the GBL FS page!
Controller Footswitch Blocks CS1 and CS2
The FX8 now has the ability for footswitches 1-8 to operate as “Control Switches”.
Control Switch 1 and Control Switch 2 now appear in the list of SOURCES on every MODIFIER page.
Using this feature, for example, you can create a BOOST footswitch (Volume Modifier) a WHAMMY effect (Pitch Block: Control Modifier) or a single footswitch that toggles two or more effects on or off in unison (BYPASS MODE modifiers).
CONTROL SWITCH 1 and 2 are footswitch blocks that can be assigned Globally or Per-Preset like any other Footswitch Block from the main Footswitch (“FS”) page. Use NAV to select the desired location and turn “VALUE” to step through the list of available footswitch assignments.
To Set Up a Control Switch Footswitch:
1. On the Footswitch (“FS”) page of the FX8, use NAV and VALUE knobs to assign CS1 or CS2 to footswitch 1 – 8
2. Add a modifier to the desired parameter, setting “CTRL SW1” or "CTRL SW2” as the SOURCE.
3. Adjust the modifier to work as desired.
Now, when you step on the footswitch, the modifier will change the value of the assigned parameter.
NOTE: Coupled with the new “Momentary Footswitch” options, Control Switches are quite powerful!
The initial value of each Control Switch is saved per scene. The initial values are set on the new Control Switches (“CTRL SW”) page of the CONTROLLERS area of the MISC page.
To Set Initial Values for a Control Switch:
1. From the main FOOTSWITCH (“FS”) page of the FX8, page right to the MISC page.
2. Select the CONTROLLERS option and press <ENTER>
3. Page to the CONTROL SWITCH (“CTRL SW”) page.
4. Set the initial value of each switch for each scene to either “ON” or “OFF”.
Bank Limit
Bank Limit is a new feature designed to prevent “oops” when stepping up or down through banks during a live performance.
It limits the available banks you can access through the footswitches with an UPPER and LOWER limit. For example, you could limit your FX8 to footswitch access to banks A through D for one gig, and banks L and M for another. Bank Limit is enabled through the global menu, and adds three new parameters to the GLOBAL SETTINGS menu.
To set up Bank Limit:
1. Navigate to the SETTINGS page of the GLOBAL menu under SETUP.
2. Set BANK LIMIT as desired: “NO”, “WRAP”, & “NO WRAP”
a. NO – Banks are NOT limited. Lower and Upper limit settings are IGNORED.
b. WRAP – Banks ARE limited and will wrap around from the highest back to the lowest (or vice versa).
c. NO WRAP – Banks ARE limited and will NOT wrap.
3. Set BANK LOWER LIMIT: A – P as desired. Cannot be higher than the UPPER limit.
4. Set BANK UPPER LIMIT: A – P as desired. Cannot be lower than the lower limit.
This feature has no effect on FX8 Edit.