FM3 Firmware Version 6.00 beta 3

Status
Not open for further replies.
Chromatizm said:
I learned the hard way that what I like to hear when there is only a guitar, what sound good when there is some other music/backing, and what works best in a live situations are things which have nothing to do in common.
Just yesterday in a jam situation I had to swap my favorite Matchless preset to a factory default "Still got the blues" preset which I would never use at home. And it sounded glorious, while my preset sucked big time.
I really don't understand how people get their presets working in both home and live situations... So much to learn. And I tune the presets when playing quite loud at home, so F-M curve shouldn't be that much of a problem.

My point it "use your ears" is sometimes the worst advise of them all. Until the ears are properly trained and educated, "use your ears" is like blind navigation on a highway in heavy traffic :)
Click to expand...

I was referring to checking levels. That said if you can't trust your ears then....not sure even how to respond. How would one have any idea what a good vs a bad sound is?
 
If anyone was following the issue I had with the latest firmware... it wasnt the firmware, it was the DI unit I was using.
I've got everything setup in a rack and had no problems before but for some reason the latest firmware did something that was enough to get me pulling everything out and testing the gear piece by piece. Turns out plugging into the FM3 was fine and going through the setup was not fine. I changed out the power supply in the DI unit and bingo!

Here's the DI signal direct to the DAW. On the left is the old power supply, right is updated one. I played the same kind of chords/riff twice and the settings on the unit were identical so yeah, massive difference here. I havent put the new FW through its paces but I played with it for 20 seconds and was like, yep this is sick... SAWEEEEEEET.

1667612972962.png

I kind of always thought it was an issue on my end but I thought it was a FM3 setting not something external. The stuff I have here is pretty set and forget, maybe the power supply started dying a slow death recently... either way, a weekend of chugga chugga-ing is ahead.
 
Chromatizm said:
I learned the hard way that what I like to hear when there is only a guitar, what sound good when there is some other music/backing, and what works best in a live situations are things which have nothing to do in common.
Just yesterday in a jam situation I had to swap my favorite Matchless preset to a factory default "Still got the blues" preset which I would never use at home. And it sounded glorious, while my preset sucked big time.
I really don't understand how people get their presets working in both home and live situations... So much to learn. And I tune the presets when playing quite loud at home, so F-M curve shouldn't be that much of a problem.

My point it "use your ears" is sometimes the worst advise of them all. Until the ears are properly trained and educated, "use your ears" is like blind navigation on a highway in heavy traffic :)
Click to expand...

I test my presets playing with music at a decent volume. It gives me a pretty good idea of how it will work with other musicians as far as cutting through.
 
Edrod said:
Happy Friday everyone.

I noticed that with the new update, if I turn on a Drive block, I get a noticeable bump in volume too. I don't recall this happening before, I'm hoping someone can shed some light on this. I might be doing something wrong
Click to expand...

One thing you can do is to save the drive blocks tweaked for level and your preferred settings. Then you can just drop it in instead of the stock block.
 
rglr said:
FM3 Firmware Version 6.00 beta 3 is now available for download:
https://www.fractalaudio.com/downloads/firmware-presets/fm3/6p0/fm3_dsp_rel_6p00_beta_3.zip

A new version of FM3-Edit is required for FW version 6.00:
https://forum.fractalaudio.com/threads/fm3-edit-1-05-10-to-support-fw-6-00-public-beta-1.188170/

My apologies for the delay with this release. I've been working hard to reduce CPU usage. I hope you find the results worth the wait.

Updates over 6.00 beta 1:
  • 6.00 beta 2
    • Fix the unavailable FC Setlist/Songs menu item from the Setup page on the hardware.
  • 6.00 beta 3
    • Fix occasional system lock up when exceeding the maximum CPU.
    • Fix minor algorithm issue in the Poweramp discovered by Cliff.
RELEASE NOTES:

NEW AND IMPROVED FEATURES​

  • Optimizations to reduce CPU. This will vary depending on blocks used and settings.
  • Added Klone Chiron model to the Drive block.
  • Added Griddle Cake model based on Crowther Hot Cake to the Drive block. The “XLF” switch on the pedal can be replicated by turning the Bass Response knob fully CW.
  • Added the following new Amp models:
    • PVH 6160 Block Crunch
    • Diamante Fire based on a Diamond Del Fuego
    • Brit Studio 20 Amp model based on a Marshall SV20H
    • Plexi 50W 6CA7 Jumped
  • New “Cygnus X-2” amp modeling:
    • Improved Amp block output transformer algorithm. New algorithm more accurately models B-H curve resulting in a clearer low end. New algorithm now also accounts for effect of speaker impedance on transformer response.
    • Improved power tube modeling. This yields better dynamics, improved low frequency accuracy and more accurate interaction with output transformer.
    • Improved cathode follower algorithm. Provides more accurate “cleanup” when volume is rolled off.
    • Improved triode algorithm more accurately models plate bypass capacitors.
    • Many amp models have been updated as a result of the aforementioned improvements.
    • Various other improvements.
  • Improved modeling accuracy for following Amp models:
    • Plexi 50W Jumped
    • Plexi 100W Jumped
    • Brit JM45 Jumped
    • 1987X Jumped
    • 1959SLP Jumped
    • Plexi 100W 1970
    • Deluxe Tweed Jumped
    • Two Stone J35 and J35 PAB
    • Fox ODS and ODS Deep
    • Nuclear Tone
    • All Solo 88, 99 and 100 models
    • All Bogfish models
    • All Spawn Q-Rod models
    • All Spawn Nitrous models
    • All Vibrato Verb models
    • All Deluxe Verb models
    • All Double Verb models
    • All Brit 800 models
    • All Brit JVM models
    • All Friedman BE/HBE V2 and V3
    • Friedman Small Box
    • Cornfed M50
  • Drive block improvements. Drive block now incorporates the “Chase Transform Technique” for converting analog networks to equivalent digital filters. This improves accuracy in the high frequency region.
  • New “Block Mixer” algorithm results in faster/quieter scene and channel changes.
  • New Speaker Drive algorithm in Amp block. This new algorithm more accurately models the frequency dependent distortion of guitar loudspeakers. The default value (upon resetting the block) is 2.0 which gives roughly 1 dB of compression. Setting the value to 0.0 defeats the speaker drive modeling. Higher values give a smoother and more focused sound, rounding off the “sharp edges” and yielding greater compression.
  • Added Speaker Thump to Amp block. This models the dynamic, nonlinear behavior of a guitar speaker. A value of 5.0 roughly corresponds to an amp running into a speaker rated at the same power as the amplifier, i.e., a 100W amplifier running into a 100W speaker. The reset value is a conservative 2.5 which represents, i.e., a 50W amp running into a 100W speaker. Note that the majority of the response is in the subsonic region and the effect is primarily tactile. Existing presets are not affected and the value will be zero.
  • Improved Amp block output transformer modeling. This requires updated Transformer LF/HF values for the amp models. Existing presets are automatically updated to the new values upon recall.
  • Changed “Drive” to “Gain” for Amp block preamp gain as this is more consistent with naming in real amps.
  • Added “Overdrive Volume” parameter to Dumble-type amp models (ODS-100, Two Stone, etc.). This is sometimes labeled “Ratio” or “Lead Master”. As the Master Volume on these amps often has a bright capacitor the Overdrive Volume control allows setting the Master Volume higher to counteract the bright cap and then lowering the power amp drive with the Volume.
  • Added “Plate Suppressor Diodes” parameter. This value is set automatically when the amp model is chosen but the user can override the default setting. Most amps do not have suppressor diodes but some do (e.g., Trainwreck Express). These diodes (also called “snubber” or “flyback” diodes) prevent undershoot on the power tube plates due to inductive kick and reduce upper harmonics thereby reducing “fizz”.
  • Improved speaker impedance curve fitting algorithm. This results in more accurate and more “colorful” modeling as the previous algorithm tended to damp box resonances somewhat. All the speaker impedance curves have been updated using the new routine.
  • Added speaker impedance curves:
    • 4x12 Lerxst Omega
    • 1x12 Deluxe Oxford
    • 4x12 Hipower Pete T
    • 4x12 Hipower Lindsey B
    • 4x12 USA Semi-Open
    • 2x12 Dizzy RV
    • 4x12 London Town Tall
    • G12T-75
    • 2x12 Class-A Greenback
    • 2x12 Two Stone 1265
  • Added cross feedback parameters to Quad Parallel type in Multitap Delay block.
  • Increased the range of the Level parameters in Multitap Delay to -100% to +100%.
  • SPDIF output level will no longer be dependent on the volume knob.

FC FEATURES​

  • Added new Setlists/Songs feature, which can be used with the onboard switches and/or an FC Controller to access presets and scenes in custom order during live performance. A new Setup menu area provides full access from the front panel, with a corresponding new area of FM3-Edit which offering import/export and more. For additional details, please see the Setlists & Songs Mini-Manual, located at: https://www.fractalaudio.com/sss-manual

FIXES​

  • Fixed wrong coupling capacitor value in 1959SLP Treble, 1959SLP Jumped and 1987x Treble amp models.
  • Fixed wrong resistor value in tone stack of Solo 88 Rhythm and Lead models. Probably not audible though.
  • Fixed low frequency behavior of Recto2 models due to loss of precision.
  • Fixed wrong treble pot taper in CA3+ models.
  • Fixed wrong capacitor value in Friedman HBE V1 Fat model.
  • Fixed wrong resistor value in AC-20 12AX7 models.
  • Fixed wrong Depth knob taper in Archean models.
  • Fixed scale not being set when first attaching a modifier to a LOG parameter.
  • Fixed Bypass grayed out on Reverb EQ page.
  • FC: Layout Link will no longer unduly trigger when exiting the Tuner.
  • FC: Preset: Select in Bank switches now stop flashing when the preset is changed by any means other than an FC footswitch (editor, front panel, etc.)
  • FC: Preset: Select in Bank switches now flash consistently when used with Bank: Select switches.
  • FC: Preset: Toggle in Bank now consistently and correctly loads "Primary" preset after changing the bank.
Click to expand...
Can someone please help me? I’m using both of these links and am not getting anything. The firmware link only gives me a couple pdf files and a SYX file. I think I have the current editor but cannot get past 5.03 on the hardware itself.
 
Ejhart said:
Can someone please help me? I’m using both of these links and am not getting anything. The firmware link only gives me a couple pdf files and a SYX file. I think I have the current editor but cannot get past 5.03 on the hardware itself.
Click to expand...
You have to send the syx file to the fm3. Can be done with fractal bot (you can also open this from fm3 edit).

You can google the below:

https://www.g66.eu › ManualsPDF
AXE-FX III / FM3 FIRMWARE UPDATE GUIDE
 
Hi all, first post in ages. I had my FM3 (latest beta fw) become unresponsive during a set last night and had to power cycle. Never had issues on 5.03 I know this is not enough info to be helpful but just thought I'd share as general feedback. Thanks!

As an aside, I had one of those old school sound guys tell me that my tone sounded "digital". I assure you it sounded great through my CLR. I then realised that he had a 3db treble boost engaged on the front of house monitors. Grrrr.
 
ninja9 said:
Hi all, first post in ages. I had my FM3 (latest beta fw) become unresponsive during a set last night and had to power cycle. Never had issues on 5.03 I know this is not enough info to be helpful but just thought I'd share as general feedback. Thanks!

As an aside, I had one of those old school sound guys tell me that my tone sounded "digital". I assure you it sounded great through my CLR. I then realised that he had a 3db treble boost engaged on the front of house monitors. Grrrr.
Click to expand...
I always try to tell the sound guy "line level, flat EQ to start"...
 
Cx2 6.03 beta delivered like I've never heard my FAS ever sound, full, rounded, balanced and thick with excellent clarity.
Atomica Hi rules!
My soundguy tonight said the FM3 sounded the fullest he has heard in his 50,000 watt RCF sound system in 10 years of his experience with FAS products. Said he was selling his Kemper and wants my preset. Haha
 
I think 6.03 probably needs more DSP than the last FW. The same preset that had running, at top of DSP but working, on 6.02, after update last night to 6.03 overloads FM3 after restart the unit (not more changes in quality levels or blocks, just the update), and I had to put off a block to make the preset work.
Did anyone notice that too?
 
pmruiz1971 said:
I think 6.03 probably needs more DSP than the last FW. The same preset that had running, at top of DSP but working, on 6.02, after update last night to 6.03 overloads FM3 after restart the unit (not more changes in quality levels or blocks, just the update), and I had to put off a block to make the preset work.
Did anyone notice that too?
Click to expand...
Please upload the preset here if it’s not a paid preset. The CPU usage should have gone down. We need to see the preset to tell you why it may have gone up.
 
chris said:
Please upload the preset here if it’s not a paid preset. The CPU usage should have gone down. We need to see the preset to tell you why it may have gone up.
Click to expand...
Sorry, I modified it to can play with it in 6.03 and I don't have the original preset in 6.02 already...
But it worked in 6.02 and needed more DSP in 6.03.
Thanks!!
 
Hi All, I need to restore a backup done with 5.03 and now I'm on 6 beta 3. Do I need to return with FW5.03 before restore or can I do it directly with 6.03?
I need to do this to recover a preset that I modified after the backup
 
Status
Not open for further replies.
Back
Top Bottom