https://www.fractalaudio.com/downloads/firmware-presets/axe-fx-3/30p0/axefxiii_dsp_rel_30p00.zip
Be sure to install the firmware before installing the Dyna-Cabs.
Axe-Edit Installers:
OSX
https://www.fractalaudio.com/downloads/Axe-Edit-III/Axe-Edit-III-OSX-v1p14p20.dmg
Win64
https://www.fractalaudio.com/downloads/Axe-Edit-III/Axe-Edit-III-Win-v1p14p20.exe
Win32
https://www.fractalaudio.com/downloads/Axe-Edit-III/Axe-Edit-III-Win32-v1p14p20.exe
Axe-Fx III Firmware Release Notes
30.00
NOTE: This firmware requires installation of Dyna-Cabs version 1.09. Refer to the Dyna-Cab Installation Guide for details. Be sure to install the firmware before installing the Dyna-Cabs.
Added Tracking Mode parameter to Synth and Ring Mod blocks. When set to “BASS” the pitch tracking range is shifted down one octave with the lowest detectable note being approximately F#0.
Increased upper range of pitch detectors to approximately F#6. This prevents loss of tracking if playing at the 24th fret on the high E string and bending up a whole step.
Added “PI Fuzz – Bass” model based on a Deluxe Bass Big Muff Pi.
Added “NoAmp Bass DI” based on a SansAmp BassDriver DI.
Added “NoAmp Bass Pre” based on a SansAmp BassDriver DI with the speaker emulation bypassed. This can be used into a Cabinet block or as a boost into an Amp block.
Added “Royal Bass DI” based on a Noble Bass Preamp DI. The model has been modified with more gain so that it can be overdriven. With the Drive knob at 5.00 the gain is the same as the actual preamp. Also, instead of a Low Cut switch, the model uses an adjustable Low Cut control.
Added “7 Band Pedal” Graphic EQ type based on a Boss GE-7.
Added “7 Band Bass Pedal” Graphic EQ type based on a Boss GE-7B.
Added “1x8 Princetone” Dyna-Cabs captured from a 5F2 Tweed Princeton w/ a very nice sounding 8” Jupiter speaker. Added corresponding Speaker Impedance Curve.
Added “1x12 Black Magick” Dyna-Cabs captured from a Supro Black Magick with a Jensen P12Q speaker. Added corresponding Speaker Impedance Curve.
Added “8x10 SV Bass” Dyna-Cabs captured from an Ampeg SVT. Added corresponding Speaker Impedance Curve. Thanks to Mike "Dr. Bonkers" Santasiero for the files from his Dyna-Cab Pack, "Dr. Bonkers 8x10 SBB Bass". If you like this selection of mics, you can purchase the entire pack for Cab Lab at
https://shop.fractalaudio.com
Improved accuracy of Sustain control vs. position in PI Fuzz models.
Fixed wrong resistor value in Blackglass 7K model. Remastered model as a result.
Fixed incorrect gain in Colortone Booster and Colortone OD models.
Fixed wrong capacitor value in all Blackface Vibrato models (Deluxe Verb, Double Verb, Super Verb, Vibroverb). Change probably isn’t very noticeable.
Fixed wrong resistor value in Deluxe Verb Normal model. Remastered model as a result.
Fixed Modern Gate type can get stuck closed if input above threshold during boot.
Changed name of “1x12 Brit G12M” speaker impedance curve (obtained from a 1x12 Divided-by-13 CJ11) to “1x12 Div13 CJ11” prevent confusion.
Various other fixes and improvements.
