We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by Satch4u3

Axe-Fx III Firmware 25.00 Release

The new firmware sounds great, and the Kill Dry is an amazing addition! Thank you!
- Satch4u3
- Post #28
- Apr 9, 2024
- Forum: Axe-Fx III Discussion
Axe-Edit III 1.13.14

Ohh! Love the new amp control layouts.
- Satch4u3
- Post #11
- Jan 30, 2024
- Forum: Axe-Edit III
Axe-Fx III Firmware 24.00 Public Beta #2

Excited to see the Mark V channels appearing in these updates! I used to gig with a Mark V with horizontal Recto 212 cab years ago. Always loved that amp. Funny enough, I sold that setup to fund my first Axe Fx 2! haha Looking forward to exploring it's sound again!
- Satch4u3
- Post #52
- Dec 17, 2023
- Forum: Axe-Fx III Discussion
HAPPY BIRTHDAY CLIFF!

Happy belated birthday, Cliff!!
- Satch4u3
- Post #80
- Nov 30, 2023
- Forum: The Lounge
Who else never really uses the drive block(s)?

I have never used them either. I have owned some over the years, but always preferred straight up amp gain. However, I do use a Princeton Rev patch with a Tone of Kings to gain stage and give the amp a little more attack.
- Satch4u3
- Post #37
- Nov 16, 2023
- Forum: Axe-Fx III Discussion
Axe-Fx III Firmware 23.00 Release Candidate #2 (Beta #7)

Possible bug with the Octave Divider? I can barley hear any of the 1 Octave and 2 Octave down, even with the mix set to 50%.
- Satch4u3
- Post #46
- Nov 10, 2023
- Forum: Axe-Fx III Discussion
Axe-Fx III Firmware 23.00 Release Candidate #2 (Beta #7)

Rotary bug confirmed here as well.
- Satch4u3
- Post #43
- Nov 10, 2023
- Forum: Axe-Fx III Discussion
[SOLVED] Please help. Am I overlooking something with 4CM (Diezel VH4 and FM3)?

Oh I missed that part. Try another humbuster cable maybe. However, the Morley Humno you have order might be your ticket if it's a ground loop issue. Post your preset so we can have a look. Also, does the noise go away at all when you plug your guitar straight in to your amp, just leaving the...
- Satch4u3
- Post #13
- Nov 3, 2023
- Forum: FM3 Discussion
[SOLVED] Please help. Am I overlooking something with 4CM (Diezel VH4 and FM3)?

Use a humbuster cable from the out 2 of your FM3 into the input of your amp. Makes a big difference. Channel 3 of my Bogner XTC is unusable with my Axe 3 in 4CM, without it. Also, USB connections from your FM3 to your PC or MAC maybe culprits of some noise in this config as well.
- Satch4u3
- Post #10
- Nov 3, 2023
- Forum: FM3 Discussion
Axe-Fx III Firmware 23.00 Release Candidate (Beta #6)

Ahh Yes, I think you're correct. I used to use Medium Hall, but I think I switched to Rich Hall a while ago. Apologies!
- Satch4u3
- Post #47
- Nov 3, 2023
- Forum: Axe-Fx III Discussion
Axe-Fx III Firmware 23.00 Release Candidate (Beta #6)

New reverbs sound great. Not a huge deal, but I did notice that my presets are pulling up a different reverb since updating to this most recent firmware. I was using a Medium Hall. Now its pulling up Mechanic's Hall in it's place. Even after doing "Refresh After New Firmware". Also using Edit...
- Satch4u3
- Post #33
- Nov 3, 2023
- Forum: Axe-Fx III Discussion
Fletcher Munson curve - EQ solution for different volume playing

With gigging presets on a loud PA, On the cab block, start by doing a low cut at 100 Hz and high cut from any where between 6000 Hz and 8000 Hz. I mostly use a PEQ block after the cab block for this, as I can chip away at other frequencies with it if I need to.
- Satch4u3
- Post #4
- Oct 16, 2023
- Forum: Axe-Fx III Discussion
Anyone try using UA Ox Stomp for their cabs?

Haha I have attempted that actually but couldn’t quite get the results I was hoping for. User error I am sure.
- Satch4u3
- Post #4
- Oct 12, 2023
- Forum: Axe-Fx III Discussion
Anyone try using UA Ox Stomp for their cabs?

I using an Ox Box with a Line In mod (basically the same as an Ox Stomp) with my Axe III for cab sim, and it sounds fantastic. I do plan on getting an Ox Stomp when they become readily available here in Canada.
- Satch4u3
- Post #2
- Oct 12, 2023
- Forum: Axe-Fx III Discussion
Acoustic Guitar through the Axe FX III?

I am switching between electric and acoustic at gigs as well. Running a Martin HD28 with a Fishman piezo (can't remenber the exact model) directly in to the Axe, and it always sounds great. I have never been a fan of using acoustic CAB IRs in a full band context or using the Axe fx preamp block...
- Satch4u3
- Post #10
- Jun 22, 2023
- Forum: Axe-Fx III Discussion