Recent content by jtaylor14

  1. J

    Sending Signal From FM3 Output 2

    It's not a waste of time if you want to have Out2 pre-cab block. I run a solid state amp and have a 2x12 on stage. In every preset I have an Out2 that gets a signal run to it pre-cab so I don't have cab sim running to the stage amp/cab. No need to color the cab on stage with a cab sim unless...
  2. J

    FM3 Firmware Version 5.01

    Absolutely. I've been doing it for years. I don't use OnSong though, I've been using Bandhelper. Our whole band uses it and it's been flawless. Drummer even uses it for clicks/tempo. Program our set lists, tap the song, switches to the right preset. Hardly any tap dancing except to go...
  3. J

    Bagpipe preset

    I adapted the earlier version of bagpipes and use it on my FM3 to play Long Way to the Top. FYI, my band plays a half step down, so you'll have to adjust the drone to the proper pitch if you tune standard. This uses legacy factory cabs, so all you need is the preset, attached. Good luck...
  4. J

    FM3 Firmware Version 4.00 beta 2

    Ok, so I've been playing with the beta .02 for the last 2 nights and discovered a few things, I apologize if I'm repeating things as I've been reading so much I forget where things left off with certain issues. My experience: In each of my presets I have an Out1 and Out 2 block. I have my...
  5. J

    Wish Pitch block update

    +1
  6. J

    Wish Default Footswitch Layout Per Preset

    Yes, I ended up doing per-preset footswitches, but it was a much more manual process.
  7. J

    Wish Default Footswitch Layout Per Preset

    I'll have to try these suggestions out, but ultimately it seems like I'm pressing footswitches to arrive at what I'm after, rather than having a default layout/view per preset. The reason I'm asking for this is because I use Bandhelper and Midi over bluetooth for gigs. I'm in the app, hit a...
  8. J

    AX8 preset conversion to FM3?

    Be careful to check all settings when porting using Fractool. I noticed this past week that some of my presets with Out2 got a little crazy. I moved patches over and some settings didn't carry over 1:1, and with my Out2 block (I use Out1 with Cab sim to FOH, Out2 is pre-cab and goes to my...
  9. J

    Wish Default Footswitch Layout Per Preset

    I think it could be handy to have a default footswitch layout per preset. Ex. Preset 399 has clean/crunch/lead scenes. When I choose preset 399, the three footswitches default to Scene Mode. I have a preset 400 that is crunch Marshall, but in one song where i use it I have to switch to a...
  10. J

    FM3 Preset and Scene Select with Bandhelper

    It's a multi-purpose preset. I could make an identical preset and have it default to scene 2, just trying to avoid clutter. I control the bulk of what I play through Bandhelper/Midi and won't have to touch the FM3 much during gigs.
  11. J

    FM3 Preset and Scene Select with Bandhelper

    Arlo helped with a solution by turning my onto a settings within the Bandhelper app in case anyone else runs into this. Go into Settings on Bandhelper, then Audio & Midi, scroll down to the line below Midi Preset Order that says ...with Delay Between and add a .4 second delay. With that set...
  12. J

    Layout not sticking to preset

    I would like to jump in and say that I too would see a benefit of choosing a default footswitch layout per preset. For my case, there are some songs I play where I can't fit the different changes into one preset without hitting CPU limits, so I have to resort to two or three presets for a song...
  13. J

    FM3 Preset and Scene Select with Bandhelper

    I set the FM3 (using midi channel 2) Scene Change back to 34, so I have Preset 401, Scene 2 as: Program Change 3 0 17 Control Change 34 1 Midi from Bandhelper to the FM3: sending data [B1, 00, 03, B1, 20, 00, C1, 11] to all ports sending data [B1, 22, 01] to all ports received data [B1, 00, 03]...
  14. J

    FM3 Preset and Scene Select with Bandhelper

    I'm coming from the AX8 and had Bandhelper for having set lists for each gig, pressing a song and it would send midi commands to change both preset and scene. I'm trying to do the same thing in FM3 but am stuck. I'm trying to select preset 401, scene 2. Here's what I've done: Added a new...
  15. J

    Fixed FM3 freezing

    I had the unit freeze under different circumstances. I was just modifying a preset, had the looper added so I could play a phrase, then adjust eq and cabs to my liking, once done, I went to Output 1 to check levels, saw that it was too hot, went back to amp block to adjust level and the unit is...
See more
Back
Top Bottom