Rippin' new Dumble patch track. (new) Patch settings posted!

Re: Rippin' new Dumble patch track. Remixed!

I wrote down the settings....... It may need some minor tweaks to smooth the 2-3K bite, and bump the 900-1100hz range. Just a db or two I think. Let me know.....

Patch optimized for bridge humbucker in Gibson scale type guitar. Alnico II type pup with moderate, not screaming gain.

Firmware 9
Amp 1 - HAD ODS 1
Drive - 4.61
Bass - 7.8
Mid - 8.46
Treb - 4.33

Presence - 1.1
Depth - .6
Damp - 3.03
Sag - 1.3
Master - 7.3
Level - -2db

Warmth - 1.06
Thump - 1.6
Lo Cut - 80hz
Hi Cut - 3500 hz
Bright cap - .257nf
Stack - Skyline
Tonestack Freq - 1330hz
Stack location - Pre
Presence freq - 1205hz
Power tube bias - .378
B+ Cap - 7.64
Tran LF - 21.8
Tran HF - 14301
Tran Match - 7.05
Speaker Res - 80hz
Stabilizer off
Presence - Passive

Cab - 2X12 Custom - 2X12 Boutique
Stereo
Air 25%
Air Freq 3500HZ
Linked, no mics saved in patch. Experiment.....

Delay can be a 267ms, 8% feedback, 10% mix
Reverb can be Large Room, 3.23 sec, 15-22% mix

Make sure the Axe Fx input is set for max input gain with no clipping.
 
Re: Rippin' new Dumble patch track. Remixed!

scottl said:
I wrote down the settings....... It may need some minor tweaks to smooth the 2-3K bite, and bump the 900-1100hz range. Just a db or two I think. Let me know.....

Patch optimized for bridge humbucker in Gibson scale type guitar. Alnico II type pup with moderate, not screaming gain.

Firmware 9
Amp 1 - HAD ODS 1
Drive - 4.61
Bass - 7.8
Mid - 8.46
Treb - 4.33

Presence - 1.1
Depth - .6
Damp - 3.03
Sag - 1.3
Master - 7.3
Level - -2db

Warmth - 1.06
Thump - 1.6
Lo Cut - 80hz
Hi Cut - 3500 hz
Bright cap - .257nf
Stack - Skyline
Tonestack Freq - 1330hz
Stack location - Pre
Presence freq - 1205hz
Power tube bias - .378
B+ Cap - 7.64
Tran LF - 21.8
Tran HF - 14301
Tran Match - 7.05
Speaker Res - 80hz
Stabilizer off
Presence - Passive

Cab - 2X12 Custom - 2X12 Boutique
Stereo
Air 25%
Air Freq 3500HZ
Linked, no mics saved in patch. Experiment.....

Delay can be a 267ms, 8% feedback, 10% mix
Reverb can be Large Room, 3.23 sec, 15-22% mix

Make sure the Axe Fx input is set for max input gain with no clipping.
Click to expand...
Thanks for posting that. I know it took a lot of time.
I really appreciate it.
 
This is a real fun patch to play, I played with the mids a bit with a tonebender fuzz. Good rippin' fun.
:D
 
Good job with the syx Andrew!!

I made a mistake btw. The speaker cab is 2X12 Custom / 2X12 Boutique

Thanks!!
 
scottl said:
Good job with the syx Andrew!!

I made a mistake btw. The speaker cab is 2X12 Custom / 2X12 Boutique

Thanks!!
Click to expand...

So you have 2 different cabs ... right?
I will make the correction, btw if you use 2 cabs intead of the Stereo Cab you will
be using the Hi-Rez IR's (Stereo cab uses Lo-Rez version)

;)
 
Andrew,

I am really new at this. Can you tweak the patch, specifically the cabs? I was unaware of what you talk about.

Feel free to make adjustments to other areas as well to enhance the "chirp" factor while keeping any rasp or harshness out.

Thanks!


AndrewSimon said:
scottl said:
Good job with the syx Andrew!!

I made a mistake btw. The speaker cab is 2X12 Custom / 2X12 Boutique

Thanks!!
Click to expand...

So you have 2 different cabs ... right?
I will make the correction, btw if you use 2 cabs intead of the Stereo Cab you will
be using the Hi-Rez IR's (Stereo cab uses Lo-Rez version)

;)
Click to expand...
 
scottl said:
Andrew,

I am really new at this. Can you tweak the patch, specifically the cabs? I was unaware of what you talk about.

Feel free to make adjustments to other areas as well to enhance the "chirp" factor while keeping any rasp or harshness out.

Thanks!
Click to expand...

Scott you did a fabulous job,
I can tell from the preset that you tweaked every parameter there is!

I, on the other hand, have very little knowledge, I never played a Dumble
or even a Dumble clone.
All I can do is adjust to my taste.
Here is how I saved your preset with two cabs, no delay and different Reverb:

http://www.andras-shimon.com/AXE-FX/Lerner2.syx

I also made a Low-Gain version that I absolutely love:

http://www.andras-shimon.com/AXE-FX/LernerLowGain.syx

And while we're at it, here is a clean Fender preset that I'm tweaking and loving lately.... a lot!

http://www.andras-shimon.com/AXE-FX/FenderMagic6.syx

Give it a spin and adjust to taste.

:D
 
Love what you are doing with the fender patch


AndrewSimon said:
scottl said:
Andrew,

I am really new at this. Can you tweak the patch, specifically the cabs? I was unaware of what you talk about.

Feel free to make adjustments to other areas as well to enhance the "chirp" factor while keeping any rasp or harshness out.

Thanks!
Click to expand...

Scott you did a fabulous job,
I can tell from the preset that you tweaked every parameter there is!

I, on the other hand, have very little knowledge, I never played a Dumble
or even a Dumble clone.
All I can do is adjust to my taste.
Here is how I saved your preset with two cabs, no delay and different Reverb:

http://www.andras-shimon.com/AXE-FX/Lerner2.syx

I also made a Low-Gain version that I absolutely love:

http://www.andras-shimon.com/AXE-FX/LernerLowGain.syx

And while we're at it, here is a clean Fender preset that I'm tweaking and loving lately.... a lot!

http://www.andras-shimon.com/AXE-FX/FenderMagic6.syx

Give it a spin and adjust to taste.

:D
Click to expand...
 
You must log in or register to reply here.
Back
Top Bottom