Behringer FCB1010 Tips for Stock PROM

Kruegmeister

Kruegmeister

Experienced
Note: I use mine in Bank Mode where I have 10 Presets to Choose From.

Preset Mapping - Which Program comes up when you press button.
You have to Select the Bank with the Bank Up Down and then Select a Preset 1-10 (It should be lit up)
  1. Press and Hold Down Button (2.5 sec)
  2. Press Up to Confirm
  3. Press 1 Button (Always 1, you selected the preset prior to Holding down)
  4. Press Up to Confirm
  5. Enter Patch to Recall (Depends if you have Display Offset on or OFF could make you off by 1)
  6. Press Up to Confirm
  7. Press and Hold Down Button to Save (2.5 sec)

Footpedal Mapping - Continuous Control of Parameters
You have to Select the Bank with the Bank Up
  1. Down and then Select a Preset 1-10 (It should be lit up)
  2. Press and Hold Down Button (2.5 sec)
  3. Press Up to Confirm
  4. Press 8 or 9 Button (8 is Left Pedal)
  5. Press Up to Confirm
  6. Enter CC Number (11 is MultiFX, 4 Wah, Volume 7)
  7. Press Up to Confirm
  8. Enter Minimum (0-127, 0 is OFF and 127 Full Volume)
  9. Enter Maximum (0-127, 0 is OFF and 127 Full Volume)
  10. Press and Hold Down Button to Save (2.5 sec)


You can also send A Toggle upon loading each preset.
For instance I setup a Tuner Patch on Bank 5 preset 5
  1. Press and Hold Down Button (2.5 sec)
  2. Press Up to Confirm
  3. Press 6 Button
  4. Press Up to Confirm
  5. Enter CC to send (Tuner is 15)
  6. Press Up to Confirm
  7. Enter Control Value (127)
  8. Press and Hold Down Button to Save (2.5 sec)

If you wanted Switch 10 to be Tube Screamer Toggle
You would Delete the Program Change
The Control Value Gets Reversed depending if you want the Tube Screamer on or off at First Patch Load. This example Drive 1 is OFF at 1st Load.
You also have to have "IGNORE REDUNDANT PC" ON (Page 135 Manual) This parameter determines whether the Axe-Fx II will process or ignore Subsequent MIDI program change messages.
You have to Select the Bank with the Bank Up Down and then Select a Preset 1-10 (It should be lit up)
  1. Press and Hold Down Button (2.5 sec)
  2. Press Up to Confirm
  3. Press and Hold the 1 Button, its light will go off. Now it sends no Program Change Message.
  4. Press and Hold the 6 Button (CC1) its light will go on (Unless it was already on, Press Hold to Toggle...)
  5. Press and Hold the 7 Button (CC2) its light will go on (Unless it was already on, Press Hold to Toggle...)
  6. Press 6 Button
  7. Press Up to Confirm
  8. Enter CC to send (Drive 1 Bypass 49)
  9. Press Up to Confirm
  10. Enter Control Value (0)
  11. Press Up to Confirm
  12. Press 7 Button
  13. Press Up to Confirm
  14. Enter CC to send (Drive 1 Bypass 49)
  15. Press Up to Confirm
  16. Enter Control Value (127)
  17. Press Up to Confirm
  18. Press and Hold Down Button to Save (2.5 sec)



I/O CONTROL (Page 170 of the Manual)
Default CC assignments appear in the table below:
Function
CC Function CC Function CC
Input Volume 10 Delay 1 Bypass 47 Reverb 1 Bypass 83
Out 1 Volume 11 Delay 2 Bypass 48 Reverb 2 Bypass 84
Out 2 Volume 12 Drive 1 Bypass 49 Ring Modulator Bypass 85
Bypass 13 Drive 2 Bypass 50 Rotary 1 Bypass 86
Tempo 14 Enhancer Bypass 51 Rotary 2 Bypass 87
Tuner 15 Filter 1 Bypass 52 Synth 1 Bypass 88
External Control 1 16 Filter 2 Bypass 53 Synth 2 Bypass 89
External Control 2 17 Filter 3 Bypass 54 Tremolo 1 Bypass 90
External Control 3 18 Filter 4 Bypass 55 Tremolo 2 Bypass 91
External Control 4 19 Flanger 1 Bypass 56 Vocoder Bypass 92
External Control 5 20 Flanger 2 Bypass 57 Volume/Pan 1 Bypass 93
External Control 6 21 Formant 1 Bypass 58 Volume/Pan 2 Bypass 94
External Control 7 22 FX Loop Bypass 59 Volume/Pan 3 Bypass 95
External Control 8 23 Gate/Expander 1 Bypass 60 Volume/Pan 4 Bypass 96
External Control 9 24 Gate/Expander 2 Bypass 61 Wahwah 1 Bypass 97
External Control 10 25 Graphic EQ 1 Bypass 62 Wahwah 2 Bypass 98
External Control 11 26 Graphic EQ 2 Bypass 63 Amp 1 X/Y 100
External Control 12 27 Graphic EQ 3 Bypass 64 Amp 2 X/Y 101
Looper Record 28 Graphic EQ 4 Bypass 65 Cab 1 X/Y 102
Looper Play 29 Megatap Delay Bypass 66 Cab 2 X/Y 103
Looper Once 30 Multiband Comp 1 Bypass 67 Chorus 1 X/Y 104
Looper Dub 31 Multiband Comp 2 Bypass 68 Chorus 2 X/Y 105
Looper Rev 32 Multi Delay 2 Bypass 69 Delay 1 X/Y 106
Looper Bypass 33 Multi Delay 2 Bypass 70 Delay 2 X/Y 107
Global Bypass 34 Parametric EQ 1 Bypass 71 Drive 1 X/Y 108
Volume Increment 35 Parametric EQ 2 Bypass 72 Drive 2 X/Y 109
Volume Decrement 36 Parametric EQ 3 Bypass 73 Flanger 1 X/Y 110
Amp 1 Bypass 37 Parametric EQ 4 Bypass 74 Flanger 2 X/Y 111
Amp 2 Bypass 38 Phaser 1 Bypass 75 Phaser 1 X/Y 112
Cab 1 Bypass 39 Phaser 2 Bypass 76 Phaser 2 X/Y 113
Cab 2 Bypass 40 Pitch Shifter 1 Bypass 77 Pitch 1 X/Y 114
Chorus 1 Bypass 41 Pitch Shifter 2 Bypass 78 Pitch 2 X/Y 115
Chorus 2 Bypass 42 Quad Chorus 1 Bypass 79 Reverb 1 X/Y 116
Compressor 1 Bypass 43 Quad Chorus 2 Bypass 80 Reverb 2 X/Y 117
Compressor 2 Bypass 44 Resonator 1 Bypass 81 Wahwah 1 X/Y 118
Crossover 1 Bypass 45 Resonator 2 Bypass 82 Wahwah 2 X/Y 119
Crossover 2 Bypass 46
 
I want to program patch 10 bank 1 to be my tuner how would i do this? i have tried the toggle function tuner method but to no avail? Cheers
 
where it says 'you would delete the program change'.....how do you delete these?and if the program change is deleted, are you creating a new one when you go through the step being descibed?....i don't really understand what a program change is i guess
 
jeff fox said:
where it says 'you would delete the program change'.....how do you delete these?and if the program change is deleted, are you creating a new one when you go through the step being descibed?....i don't really understand what a program change is i guess
Click to expand...

In order to use the FCB101's switch without sending a PC msg to the Axe FX II telling it to switch to that preset #, you have to disable the FCB's preset from sending a PC msg.
So, You don't delete the Program Change, you turn it off within the preset. This is done by holding down the switch for about 1.5 seconds until it no longer lights when in select config mode.

Joedy Rose said:
I want to program patch 10 bank 1 to be my tuner how would i do this? i have tried the toggle function tuner method but to no avail? Cheers
Click to expand...

Note : I don't use Direct Select mode, as I'm not sure how this would work in that mode.
Note : I use stock factory PROM, not the UNO chip.

Basically you need to send the proper value to turn it on/off along with the CNT #.
For reference, 0-63 = off, 64-127 = on, I prefer to use 0 and 127 as it's easier to recognize when viewing configurations.
So in a nutshell, you are telling the tuner (CC15) to turn on (127) or off (0).

To Program using the FCB1010, with the preset you want to use selected;
press and hold "down" for 2.5 sec to enter config mode,
press "up" once to advance past switches configuration, the "Select" LED lights up
turn off any Program Changes by pressing and holding them for about 1.5 seconds until the no longer lit. (switch 1 - 5)
Press and hold switch "6" for about 1.5 seconds to turn on CNT1
press switch "6" once, it will begin blinking, then press "up" to enter it's configuration
set the value to 15 (default tuner CC for the Axe FX II) using expression pedal A and then press "up" to accept
set a value of 127 with expression A (turns it on), then press "up" to finish changes
press and hold "7" to turn on CNT2, repeat the same steps except use a value of 0 instead of 127 (turns the tuner off with a 2nd press of the same switch)
Press and hold "down" to save and exit configuration
 
trancegodz said:
How do you program 8 individual scenes on a stock FCB1010?

Are any of you using this Mac editor for the FCB1010 with any success? I have not tried it.
iFCB | Wabbit Wanch Design
Click to expand...

I'm programming the FCB manually, doing the riverdance. Kruegmeister has described the general process pretty accurately at the beginning of this thread. There are some other forum threads that describe this also. I'll try to dig up a link for you. I believe I created a lengthy post that describes how you can have a top row of presets (switches 6-9), with a bottom row of scene Changes (scenes 2-6) on switches 1 thru 5 on a STOCK FCB1010.

http://forum.fractalaudio.com/other-midi-controllers/61417-fcb1010-help-no-mod-no-chip.html

you should be able to use this as a guide to set up your FCB switches to do whatever you'd like them to do.
 
Last edited:
Hi Kruegmeister,

I just purchased an FCB1010 and am hoping to use your directions to get it set up exactly to do what you have done. Just Preset changing 1-10 per bank. The only thing I want to do other than this is to have a preset or 2 that would allow me to use the looper. Could I do this ? For example, I follow your directions to lets say, have presets 1,2,3 to be Clean, Dist, Lead but have a certain preset (4 for example) have a looper on that particular Axe patch, and I then use buttons 5,6,7,8 to control the looper. Is this possible?
 
Thanks Kruegmeister! You put up a lot of work on this post years ago... Just a nod to let you know that it is still helpful!!
 
You must log in or register to reply here.
Back
Top Bottom