We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by jlglespaul

How to change In1 to different rows?

Thanks !!!
- jlglespaul
- Post #5
- Jan 11, 2024
- Forum: FM9 Discussion
How to change In1 to different rows?

How to connect In1 to two different rows thru scenes, (without having both connected at same time) is this possible?
- jlglespaul
- Thread
- Jan 11, 2024
- Replies: 4
- Forum: FM9 Discussion
No output from OUT 2?

Think i got it
- jlglespaul
- Post #6
- Sep 7, 2023
- Forum: FM9 Discussion
No output from OUT 2?

I am trying to set up so OUT 1 goes to PA main and OUT 2 goes (mono) to FRFR Speaker, what needs to change? if OUT 1 is set to stereo and i use COPY OUT 1 will OUT 2 be stereo? Should i use OUT 3 for FRFR? ps i understand this currently is sending looper to OUT 2
- jlglespaul
- Post #5
- Sep 7, 2023
- Forum: FM9 Discussion
No output from OUT 2?

I can not find setting that turns OUT 2 on or off?
- jlglespaul
- Thread
- Sep 6, 2023
- Replies: 9
- Forum: FM9 Discussion
FM9 Output settings

thanks !
- jlglespaul
- Post #3
- Sep 5, 2023
- Forum: FM9 Discussion
FM9 Output settings

What should my setting be for Output 1 going to main PA -10 or +4 dbV? What should if be for Output 2 going to FRFR Speaker? thanks
- jlglespaul
- Thread
- Sep 5, 2023
- Replies: 5
- Forum: FM9 Discussion
Looper - output right or left only?

how do you “patch” looper to left?
- jlglespaul
- Post #5
- Jul 30, 2023
- Forum: FM9 Discussion
Looper - output right or left only?

When I pan Balance control it changes input and output, I was hoping to have just the recorded output panned? Also I get a change to my signal like it is far away?
- jlglespaul
- Post #4
- Jul 30, 2023
- Forum: FM9 Discussion
Looper - output right or left only?

i think i accomplished before with my Axe III, it helps when soloing over a looper track. does anyone have a preset that does this or info so i can understand if a vol/pan or mixer block is required?
- jlglespaul
- Thread
- Jul 28, 2023
- Replies: 6
- Forum: FM9 Discussion
FM9 - Suggestions on removing distorted or popping in signal?

I am looking for ideas to try to eliminate noise that comes in when strumming like it's too hot a signal? My input barely hits red. This noise occurs in unit output (not just when recording). Any suggestions would be greatly appreciated. JLG
- jlglespaul
- Thread
- Jul 5, 2023
- Replies: 2
- Forum: FM9 Discussion
FM9 FM9 - Suggestions on removing distorted or popping in signal?

CPU at 60%
- jlglespaul
- Post #4
- Jul 5, 2023
- Forum: Fractal Recordings
FM9 FM9 - Suggestions on removing distorted or popping in signal?

Ahh … I will check that thanks!
- jlglespaul
- Post #3
- Jul 5, 2023
- Forum: Fractal Recordings
FM9 FM9 - Suggestions on removing distorted or popping in signal?

I am looking for ideas to try to eliminate noise that comes in when strumming like it's too hot a signal? My input barely hits red. This noise occurs in unit output (not just when recording). Any suggestions would be greatly appreciated. JLG
- jlglespaul
- Thread
- Jul 5, 2023
- Replies: 6
- Forum: Fractal Recordings
FS Axe FX III MK I $1750 Shipped

Sold
- jlglespaul
- Post #2
- Feb 5, 2023
- Forum: For Sale