Axe-Fx III Firmware 28.05 Public Beta

[Home Skillet]

Begins with S ends with N.

Suspiration?

 

[Joe Bfstplk]

Suspiration?

Saskatchewan?

 

[randyman]

Saskatchewan?

Spacewomen?

 

[Peavey Herman]

Saskatchewan?

Supercalifragilisticexpialidociousn!

 

[unix-guy]

From 28.04 to 28.05 beta. This beta also updated them and now a soft reset is a recommendation

No... The JVM and JS410 only.

Reread the first post.

 

[deathbyguitar]

What kinds of amps have cold clipping stages?

 

[unix-guy]

What kinds of amps have cold clipping stages?

https://forum.fractalaudio.com/search/4175533/?q=cold+clipping&t=post&c[thread]=213205&o=date

 

[nambutio]

In Vox, Tweed and some more I tried I felt a considerable loss in medium and trebles tones. I put the 28.04 again and the difference is large. Perhaps it is the intention given to the new changes. I tried several adjustments but it was not easy to reach what I am used to. Sorry for my English.

 

[Joe Bfstplk]

Sorry for my English.

Yours is better than many native speakers here in the USA. You're doing fine!

 

[ben ifin]

" ... Improved Amp block output transformer modeling ... "

Captain Obvious here, but ^this^ will impact every Amp in the Axe ......

 

[lair]

Bug? - Left the unit on for 2 days after installing beta and the screen was blank this AM - Axe Edit was still connected and I was able to load a preset/change a preset but the screen stayed blank. Rebooting brought it back to normal. I've never seen a blank screen or had any screen issues.

EDIT to say the unit was on an EMPTY presets slot during those two days...

 

[FractalAudio]

Any Eye on the mesa Mark iv and iic+ triode plate frequency? They are set very different from the ones in the axe FX 2 and also compared to the jp2c..

The values are correct for our reference amps. The JP2C is not the same amp as a Mark IV or our reference Mark IIC+.

 

[Fab8040]

The values are correct for our reference amps. The JP2C is not the same amp as a Mark IV or our reference Mark IIC+.

They were not in the axe FX II...they were different and feels different...i was almost at the point to keep the 2 and sell the 3...with same values sound great and tighter in the low end.

 

[Mongillo19]

They were not in the axe FX II...they were different and feels different...i was almost at the point to keep the 2 and sell the 3...with same values sound great and tighter in the low end.

Not to be that guy but why not just adjust the values then and save it as a preset?

 

[JiveTurkey]

Not to be that guy but why not just adjust the values then and save it as a preset?

It makes much more sense to sell an entire rig.I'm kidding!

 

[Fab8040]

Not to be that guy but why not just adjust the values then and save it as a preset?

I did as i wrote...i m in the axe FX 3 with the ii values..

 

[Forever Again]

I did as i wrote...i m in the axe FX 3 with the ii values..

Different modeling engine = different results?

 

[Fab8040]

Different modeling engine = different results?

The values should be based on the real amp..

 

[Mongillo19]

The values should be based on the real amp..

But they are

 

[Fab8040]

List

But they are

So they should be the same on both machines... anyway i m not neither software or electronic engineer..i Ve Just noticed that and i found the reason why i prefered the ii over the III on that particular amps...and i own Mark iv real amp...