Gapless switching not working?

F

Fischer96

Member
Hey, i just setup a relatively big preset on my Fm9 Turbo. When switching between Crunch and Distortion or Crunch and Lead Preset i get an audible gap even though i setup everything for gapless switching. Is anyone here able to figure it out?

Preset is attached to the post, thanks in advance!
 

Attachments

You have?

Gapless -> ON
Splilover -> ALL
All presets saved under current firmware
(c) @unix-guy

I have recorded while 'walking through' your scenes, there are no gaps visible. Can you make a recording of the gap?
 
Moke said:
To insure compatibility, what firmware was this created with?
Click to expand...
Initially on 8.01 and now I’m on 9.0 beta.
Issue was always there sadly
md1234 said:
You have?

Gapless -> ON
Splilover -> ALL
All presets saved under current firmware
(c) @unix-guy

I have recorded while 'walking through' your scenes, there are no gaps visible. Can you make a recording of the gap?
Click to expand...
Weird, yeah will record something tomorrow! Thanks for checking.

Settings are all active I only use this preset so the others shouldn’t clash with this one right?
 
Fischer96 said:
Settings are all active I only use this preset so the others shouldn’t clash with this one right?
Click to expand...
Yeah, if you only you this preset, the others are not relevant indeed. To be sure, you resaved the preset? And I assume you think gapless switching worked better in 8.01?
 
unix-guy said:
Something isn't lining up, unless you mean "changing scenes" not "changing presets"?
Click to expand...
Ah sorry. I mean switching between Crunch and Distortion scenes. I only use this one preset for now. I have some other presets for tinkering which were all created on 8.01 but i never switch to those in a live setting. But yeah, i have this audible gap when switching scenes on the preset i uploaded
 
What’s the CPU on this preset
In my experience if it’s too high the gapless switching is one of the first things to cause issues as it needs time to switch
 
Randalljax said:
What’s the CPU on this preset
In my experience if it’s too high the gapless switching is one of the first things to cause issues as it needs time to switch
Click to expand...
Currently about 76% i believe. But i also had the same issues with like 55% when deleting some blocks
 
Fischer96 said:
Currently about 76% i believe. But i also had the same issues with like 55% when deleting some blocks
Click to expand...
Did you try copying this preset to another location, then editing it like you did, then saved that edited preset? I'm curious if that would change anything since they have to be resaved?
 
Thenewexhibit said:
Did you try copying this preset to another location, then editing it like you did, then saved that edited preset? I'm curious if that would change anything since they have to be resaved?
Click to expand...
Will try that later, I thought saving it in place is enough
stephanfm3 said:
Is it really a gap with no sound or is it just delayed, because you have a 2 sec hold function timeout?
Click to expand...
I have some holds in that preset but not on the scenes i mentioned. Or I don’t know extactly what you mean 🤔

The delay is not there when switching between clean and crunch for example
 
I had a gap problem switching scenes and presets. I own a Turbo unite and my CPU can run into the high 70’s. I issued a reset to all the spill over and Gapless setting and it no longer does it on my scenes. It still seems to do it switching between presets. I haven’t tested it between similar presets. Most my presets are very different from one another and figure it takes a moment to switch it all over.
 
BNewm said:
I had a gap problem switching scenes and presets. I own a Turbo unite and my CPU can run into the high 70’s. I issued a reset to all the spill over and Gapless setting and it no longer does it on my scenes. It still seems to do it switching between presets. I haven’t tested it between similar presets. Most my presets are very different from one another and figure it takes a moment to switch it all over.
Click to expand...
Did you resave the presets?
 
I had not done that. So, I just went through a row of presets and resave each individually and I think that worked. It definitely helped. I don’t notice the switch like before, but on the next row, that I did not resave, there is still a dead spot. Is there a way to send that message as a bulk command to resave all presets? Thank you for your help!
 
You must log in or register to reply here.
Back
Top Bottom