yek
Contact Fractal for your Custom Title
Could you also consider adding a feature to globallly set the high res/low res settings to a fixed value? This would help us guys with power amp and real cab.
+1
Could you also consider adding a feature to globallly set the high res/low res settings to a fixed value? This would help us guys with power amp and real cab.
That would be so damn cool!I've been contemplating putting a parameter on the Speaker page from which you can select any of the cabs that we've captured data. I think we've got about data on about 30 or so cabs.
What he said. Try puting the low res freq at 109, the Q at 2.0 and the low freq res at 5.83. This is what is was in Q1.06 and what I'm using now. Sounds SOOOOOOO damn good and makes all the difference. Probably the best tone I've ever heard ever. I can upload my preset if you care enough or you can just plug those numbers in.
This is a short test using the Recto2 Orange Modern and Recto New Mix cab. Sounds okay to me.
This is a short test using the Recto2 Orange Modern and Recto New Mix cab. Sounds okay to me.
This would be great. Please do it![]()
That sounds fucking fantastic! Care to share the patch or particulars on how you got that blistering wall of sound? Two tracks panned L/R I assume?
That sounds incredible
The only way I have ever been able to get any of the Rectifier models to sound tight was to add a Tube Screamer block in front and severely reduce the bass using pre tone controls, bass cut switch AND the GEQ. Because of that, I tend to not use them and stick with the Mark models since they require very little tweaking to get an ultra-tight tone.I have mostly play a Mark IV and I can get it to sound basically identical to my real Mark IV but the rectifier models sounds so buzzy and tubby. I have a dual and a triple rectifier so I know that they have the quality to them but the real amps I can dial to sound decent but I can't do anything with the models in the Axe Fx. On the real amp I put a parametric eq before the amp set at 90hz and remove some low end but when I try to do that in the Axe I can't get anywhere near it. I can't get it to sound remotely like the real amp. Any one use them and have any feedback? Maybe I am missing something?
Thank you but " Damn it" (as I shake both fists into the sky during a torrential downpour). It's for an XL
Thank you but " Damn it" (as I shake both fists into the sky during a torrential downpour). It's for an XL
This would be a huge value add, IMHOThose settings are based on the "Traditional" or whatever they call the smaller cab. The new values are based on the Oversize. Perhaps I should put them back to the old values. I've been contemplating putting a parameter on the Speaker page from which you can select any of the cabs that we've captured data. I think we've got about data on about 30 or so cabs.
Many of us do.. Perhaps screen shot is amp block and routing? Anything special going on in advanced parameters, IR's?Sorry about that. I wish there were a way to down-vert a preset.
Many of us do.. Perhaps screen shot is amp block and routing? Anything special going on in advanced parameters, IR's?
Much thanks
Those settings are based on the "Traditional" or whatever they call the smaller cab. The new values are based on the Oversize. Perhaps I should put them back to the old values. I've been contemplating putting a parameter on the Speaker page from which you can select any of the cabs that we've captured data. I think we've got about data on about 30 or so cabs.
Those settings are based on the "Traditional" or whatever they call the smaller cab. The new values are based on the Oversize. Perhaps I should put them back to the old values. I've been contemplating putting a parameter on the Speaker page from which you can select any of the cabs that we've captured data. I think we've got about data on about 30 or so cabs.
That was very kind of you to go out of your way to get the screen caps. That is one gloriously LARGE tone. I added delay and reverb (YMMV) and posted the Mk II preset here: http://axechange.fractalaudio.com/detail.php?preset=4028There was a bit of tinkering, so I've zipped up the relevant screenshots.