Looking for Marshall 1962 Bluesbreaker IR's

ApocalypticKatana said:
Amplifier https://marshall.com/amps/products/amps/vintage-reissues/1962-bluesbreaker

Mic'd with your typical sm57's and Sennheiser 421's preferably

anyone know a good source to get them?
Click to expand...
https://www.celestionplus.com/product/heritage-g12m-2x12-open-back-impulse-response/

Also, check Legacy and Factory 2 Cabs, particularly the Marshalls, G12H, G12M Alnico Greenback 2x12’s and 4x12’s, Celestion.

What amps are you using? I was starting with the 59 Bassguy Jumped since it has the 5F6-A circuitry and added a tremolo for the Speed and Intensity. Also, I am trying the JM45 Jumped.
100pf Cap, Input Trim .5 Tonestack Post
2 x ECC83, 1 x ECC83 (phase splitter), 2 x 5881 and 1 x GZ34 (rectifier)
2 x 12” Speaker model Celestion G12M-25 (25W, 16Ω)
Adjust Presence for the high frequencies of the power amp. Increasing the high frequencies adds more bite to your sound.
Adjust Bass for the low frequencies of the amp. It will add bottom end and depth to your sound.
Adjust Middle for the mid frequencies of the amp, giving
you anything from scooped mids to a fat and
full sound.
Adjust Treble for the upper frequencies of the pre-amp. Your tone will get brighter as it is turned up.
Yek has some recommendations IRT to the settings of these two Amps in his Amp model's gouge.
 

Attachments

  • Fender_bassman_5f6a.pdf
    162.9 KB · Views: 11
  • Fender_Bassman_5F6-A_Circuit_Kuehnel.pdf
    1.1 MB · Views: 8
Last edited:
rhummellh said:
https://www.celestionplus.com/product/heritage-g12m-2x12-open-back-impulse-response/

Also, check Legacy and Factory 2 Cabs, particularly the Marshalls, G12H, G12M Alnico Greenback 2x12’s and 4x12’s, Celestion.

What amps are you using? I was starting with the 59 Bassguy Jumped since it has the 5F6-A circuitry and added a tremolo for the Speed and Intensity. Also, I am trying the JM45 Jumped.
100pf Cap, Input Trim .5 Tonestack Post
2 x ECC83, 1 x ECC83 (phase splitter), 2 x 5881 and 1 x GZ34 (rectifier)
2 x 12” Speaker model Celestion G12M-25 (25W, 16Ω)
Adjust Presence for the high frequencies of the power amp. Increasing the high frequencies adds more bite to your sound.
Adjust Bass for the low frequencies of the amp. It will add bottom end and depth to your sound.
Adjust Middle for the mid frequencies of the amp, giving
you anything from scooped mids to a fat and
full sound.
Adjust Treble for the upper frequencies of the pre-amp. Your tone will get brighter as it is turned up.
Yek has some recommendations IRT to the settings of these two Amps in his Amp model's gouge.
Click to expand...
That’s probably as good as I’m going to get, thanks!
 
rhummellh said:
https://www.celestionplus.com/product/heritage-g12m-2x12-open-back-impulse-response/

Also, check Legacy and Factory 2 Cabs, particularly the Marshalls, G12H, G12M Alnico Greenback 2x12’s and 4x12’s, Celestion.

What amps are you using? I was starting with the 59 Bassguy Jumped since it has the 5F6-A circuitry and added a tremolo for the Speed and Intensity. Also, I am trying the JM45 Jumped.
100pf Cap, Input Trim .5 Tonestack Post
2 x ECC83, 1 x ECC83 (phase splitter), 2 x 5881 and 1 x GZ34 (rectifier)
2 x 12” Speaker model Celestion G12M-25 (25W, 16Ω)
Adjust Presence for the high frequencies of the power amp. Increasing the high frequencies adds more bite to your sound.
Adjust Bass for the low frequencies of the amp. It will add bottom end and depth to your sound.
Adjust Middle for the mid frequencies of the amp, giving
you anything from scooped mids to a fat and
full sound.
Adjust Treble for the upper frequencies of the pre-amp. Your tone will get brighter as it is turned up.
Yek has some recommendations IRT to the settings of these two Amps in his Amp model's gouge.
Click to expand...
I’m using the jtm45 non jumped model since it says on the product page it’s essentially what it is
 
You must log in or register to reply here.
Back
Top Bottom