We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by RichStudio

R
Wah keeps turning on when switch presets

I have a preset that has a wah in the chain. The preset is saved with the wah off. When I go to another preset and then back to the first, the way is on. Any preset that has a wah in it, the wah will come on. Can't figure out how to set the AXE FX so this does not happen. Thanks
- RichStudio
- Thread
- Dec 10, 2016
- Replies: 8
- Forum: Axe-Fx II Discussion
R
Switching channels on Legacy via scenes

So I figured out how to change the amp channels with the MFC-101 when in preset mode. Still can't figure out how to do this with Scenes though. Is there a specific setting for the IA switch?
- RichStudio
- Post #7
- Jul 22, 2016
- Forum: MFC Discussion
R
Switching channels on Legacy via scenes

Still can't figure this out. I am not a midi guy. Ugh!!
- RichStudio
- Post #6
- Jul 19, 2016
- Forum: MFC Discussion
R
Switching channels on Legacy via scenes

Thanks for the help. I will try this.
- RichStudio
- Post #5
- Jul 15, 2016
- Forum: MFC Discussion
R
Switching channels on Legacy via scenes

Thanks for the response. If I set the IA button (in this case IA 01 for scene one) to none I wouldn't be able to select the Axe Fx scene, correct? Thanks again. Rich
- RichStudio
- Post #3
- Jul 14, 2016
- Forum: MFC Discussion
R
Switching channels on Legacy via scenes

Can this be done? : I have a Carvin Legacy 3 amp. Channels can be switched via midi CC#s. I have the Axe-Fx II connected via four cable method and using for effect only (no amp blocks). I would like to have three scenes. One clean (channel 1), one mid gain (channel 2), one lead (channel 3)...
- RichStudio
- Thread
- Jul 14, 2016
- Replies: 11
- Forum: MFC Discussion
R
Four cable method revisited

Thanks.
- RichStudio
- Post #3
- Jul 12, 2016
- Forum: Axe-Fx II Discussion
R
Sending midi CC# to Legacy 3 amp

Is there a way to send a midi CC# from the Axe Fx II to my Legacy 3 amp to allow the amp to change channels when I select an Axe Fx preset? The manual wasn't very specific (unless I missed something). Thanks, Rich
- RichStudio
- Thread
- Jul 12, 2016
- Replies: 1
- Forum: Axe-Fx II Discussion
R
Four cable method revisited

Hello, I have an Digitech IPB-10 processor (based off of the RP1000). When using the four cable method you can not only run effects before the pre-amp and also post, you can switch the real amps preamp out and use a virtual amp from the IPB-10. Is there a way to do this with the AXE-FX II...
- RichStudio
- Thread
- Jun 16, 2016
- Replies: 4
- Forum: Axe-Fx II Discussion
R
ISP Stealth Power Amp / Live sound questions

I am using an ISP Stealth (bridged mono) with a Marshall 2 x 12 cab (in a 4 x 12 sized cabinet). I am not sure if I should shut off cab blocks. I have had some issues where I shut off a cab block and the sound gets quite thin. I tested the ISP with my Kemper, with the speaker emulation off (not...
- RichStudio
- Post #6
- Mar 15, 2016
- Forum: Amps and Cabs