We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by mattseed

Recording with USB glitch !

I can't see this topic in the sticky header sorry. Thanks Chris, I'll do a little noodling later, record it and await for the dreaded click and post it back. Thanks for chopping In. Matt.
- mattseed
- Post #4
- Apr 11, 2015
- Forum: Axe-Fx II Discussion
Recording with USB glitch !

Hi guys I have just come to record with my axe FX II using USB for the first time. I am into a newish iMac running latest Logic ProX. When I play through logic or record I get an occasional click sound that sounds like a glitch to me. I checked I'm not running the signal to hot, so it's not...
- mattseed
- Thread
- Apr 11, 2015
- Replies: 6
- Forum: Axe-Fx II Discussion
No signal on fire up

That worked great, thank you for that. It's been bugging me a while that one.
- mattseed
- Post #3
- Mar 29, 2015
- Forum: Axe-Fx II Discussion
No signal on fire up

Hi guys. On some of my patches where I am using my SP1 volume pedal through my foot controller in the usual way when I first go to these patches there is no volume till I rock the volume pedal back n forth, then it all works as normal again ? Would anyone know why this is please ? Thanks, matt.
- mattseed
- Thread
- Mar 28, 2015
- Replies: 2
- Forum: Axe-Fx II Discussion
Awesome Mystery ???

Hi guys. I updated from 17 to 18 last week all good. One of my patches that was a Marshall now shows the amp block to be a Dumble, the OD 100 HRM. Now the odd bit is if I change the amp block to another amp and then back to either the Dumble or the original Marshall it's not anywhere near the...
- mattseed
- Thread
- Mar 28, 2015
- Replies: 20
- Forum: Axe-Fx II Discussion
Can't update my MFC 101 III

Hi gang I just updated my axe fx II to latest firmware today.....all cool there. I have just now tried to update my MFC III and when I plug it into my ace fx via a midi cable and use the supplied power adaptor and change the two parameters on the axe all as instructed. The MFC display reads...
- mattseed
- Thread
- Mar 19, 2015
- Replies: 2
- Forum: MFC Discussion
Wah wah problem !

Hi guys, I have a little problem which is my Mission SP1 pedal acts as my wah. In the presets I have made its fine but in the ones I havnt touched, I go to one and by default the wah is on but the pedal isn't working so I can't really turn it off. I know I can manually turn it off, that's not...
- mattseed
- Thread
- Dec 16, 2014
- Replies: 4
- Forum: Axe-Fx II Discussion
What happened to Chris Katsukuri's Video's??

Had to chip with much respect for the man. He patiently talked me through a glitch a while back that nobody else had the time for which I can't thank him enough. Hope all is well Chris.
- mattseed
- Post #49
- Nov 27, 2014
- Forum: The Lounge
PLEASE PLEASE HELP IM STUMPED!!!

Yeah same here, it wasn't a factory reset done by the firmware update. For me it was just this issue of loosing the first preset options all my other personal settings on my MFC are intact. And this solution was a very odd work around I could never have figured out and makes no real sense but it...
- mattseed
- Post #8
- Nov 18, 2014
- Forum: Axe-Fx II Discussion
PLEASE PLEASE HELP IM STUMPED!!!

Hi Guys, thank you all for the help this one had got me totally stumped. Now i know why, RDH thank you for sending me that past post i read down it all and could see this guy had exactly the same issue as me. The fix was very odd but i just tired it and it worked straight away. For anyone...
- mattseed
- Post #6
- Nov 18, 2014
- Forum: Axe-Fx II Discussion
PLEASE PLEASE HELP IM STUMPED!!!

Hi guys i have posted this once but not sure i have explained it well enough, so please allow me start again. My MFC III as attached to my Axe FX as per normal. For a long while everything is just fine. I just updated the software on the Axe FX and the MFC to the latest. All good except my...
- mattseed
- Thread
- Nov 18, 2014
- Replies: 8
- Forum: Axe-Fx II Discussion
MFC assign issue

Sorry for being Mr thicky....but could you just tell me exactly which setting it is that would program it to do that please. Everything I tried just does nothing and each one of those first 4 Switches just changes scenes not presets. I know this must be basic stuff but I'm a bit stumped.
- mattseed
- Post #10
- Nov 16, 2014
- Forum: MFC Discussion
MFC assign issue

Thanks Morphosis. Reveal is not flashing so all good there. Axe fx mode is set correct to II. Midis channel is set to 01 I assume that's correct. This has really got me stumped, it was all ok until this last update. All other IA's are doing what they were before even the bank up and down its...
- mattseed
- Post #8
- Nov 16, 2014
- Forum: MFC Discussion
MFC assign issue

Thanks Javajunkie I have it set to bank size 4 cuz I use my tuner on IA5 but that's as it was before. Perfmode is set to preset. The only one I'm not certain on there is reveal mode, I have gone through the settings and can't see that word anywhere, which option would that be under ?
- mattseed
- Post #6
- Nov 16, 2014
- Forum: MFC Discussion
MFC assign issue

Just reading through that part of the instructions it's not quite what I want......I don't think. Before I had it so switch 1 to 4 moved up presets from say 200 to 203 then I pressed up to move up a bank to 284 then switches moved from 284 to 287 and so on. I can't work out why it's stopped...
- mattseed
- Post #4
- Nov 16, 2014
- Forum: MFC Discussion