Recent content by frankencat

  1. frankencat

    🔥Introducing the new AM4 Amp Modeler

    How do you get to the tuner, do I need an external switch for that if I am in effects mode?
  2. frankencat

    🔥Introducing the new AM4 Amp Modeler

    Ok you got me! And thanks for including a SPDIF input. So, I think I can do this after reading the manual but I would set it up 🆙 n effects mode like this: Drive : Amp/Boost : Mod : Delay I usually take a split signal and go a>to clean amp and b> to FOH. This should be doable yes? How does this...
  3. frankencat

    Beware of Protein Powder/Shakes

    We just returned 3 boxes of the Orgain Protein Powder today. That stuff isn't cheap either at $30 a box. You try and eat healthy and find stuff like this, sheesh.
  4. frankencat

    FM3 Firmware Version 11.0 public beta 1

    Super cool. I have barely broken in FW10 and here we go again. I have a Supro and it's a killer amp, great to see it represented in Fractal world, I'm sure it will be a go to for me. Thank you!
  5. frankencat

    Aldo Nova suffers a cervical spine fracture

    Oh no. Get well soon Aldo.
  6. frankencat

    FM3 Firmware Version 10.0

    I found that if I disable/enable the USB device in Windows it starts to work again. Whatevs. Enjoying the new FW.
  7. frankencat

    Anyone still using a tube amp?

    I have a few nice amps and I just bought a Supro Saturn Reverb so we’ll see how that one sounds. 😃 I mean I am all in on modelers and have been from way back, but there are times when an amp and pedals is the correct setup for the job. But when I can walk in with the little digital rig in a box...
  8. frankencat

    FM3 Firmware Version 10.0

    Yep, I know the drill and I did all that. Rinse and repeat. The issue seems to be with the device itself. All the same I will go a grab a new USB off of Amazon just to be double-sure, plus I can always use a good quality spare. 😉
  9. frankencat

    FM3 Firmware Version 10.0

    I am having issues keeping the USB connection between the FM3 Edit and the unit. The only thing that solves it is rebooting the FM3. I don't remember having this issue before the update. I checked the cable, the drivers, the USB setting, even changed the COM port (Windows). Anybody else have...
  10. frankencat

    FM3 Firmware Version 10.0

    Wow, these comps! You made a Compressor freak VERY happy. Thank you FAS! :D :D :D
  11. frankencat

    FM3 Firmware Version 10.0

    Switched from Medium Plate to Medium Hall and then back and now I am back to 74%. Yaay Fractal FW10! :D Edit: Then switched over to North Church and happiness. The new reverbs are GREAT!! <3
  12. frankencat

    FM3 Firmware Version 10.0

    Ok update was pretty painless but I was immediately greeted with the "CPU EXCEEDED" on a very simple preset. Changing the Cab IR length from Ultra to Standard got me back but I am at 84% where I was at 78ish before.
  13. frankencat

    FM3 Firmware Version 10.0

    So here's what I am going with after reading the update guide and the release notes: 1. Update FM3 Edit to latest (1.07.09) 2. Backup 3. Install FW10 (Reboot FM3) 4. Install DynaCabs 1.06 (Reboot FM3) 5. RANF 6. Try it out!
  14. frankencat

    FM3 Firmware Version 10.0

    Can someone give me the short version of how to get from FW8 to FW10 please? Reading the update guide i see this about the Dyna Cabs. Does that mean I don't have to install them separately? Thanks.
  15. frankencat

    FM3 Firmware Version 10.0

    OK guys I think I am ready to try this. Just updated FM3 Edit to 1.07.09. I am on FW 8 currently with my old non headphone FM3.
See more
Back
Top Bottom