Waiting for Tuner Problem - MKI - Std

V

vistalee

Member
Hi guys.
I know this has been discussed loads of times but I just don't know what to do.
The typical problem.
I hit the IA16 (set to tuner in mfc setup) and the Waiting for Tuner message appears.
All Realtime messages are on and all the I/O settings are setup correctly.
I use a 7pin Midi and the phantom power via the Axe.

The strage thing I found...
When I activate the tuner over the AxeFx and THEN hit the IA16 the MFC receives all the info it needs. The tuner works.

The flex-cables inside my MFC came off once (all leds off and buttons out of function)
Might that have something to do with that? Damaged something?


I need help :-D I'm going nuts. I hate it when I just can't figure it out :-D
 
The tuner detects signals at the front input, Input 1 left (rear) and S/PDIF signal
Enable real-time MIDI SysEx communication on the Axe-Fx II (I/O > MIDI) by setting it to “Tuner” or "All".
If this message Waiting for tuner appears after pressing the Tuner switch on the MFC-101, check the following:
I/O menu: Send Realtime Sysex must be enabled on the MIDI page
Tuner menu: must display first page
The Tuner must be set to the default MIDI CC on the Axe-Fx.
 
I have a Standard.
The Realtime Sysex is set to all.
I'll give your list a try tomorrow, but I feel like I have done these things a dozen times by now :-/
What's the "Standard MIDI CC" for the Tuner?
 
Okay.....it kinda works. Thank you very much. I just don't want to have the tuner on 15. I want it on 17. But no matter what I do...I can't get it to work there. Although I set the tuner in the Axefx IO to 17 AND set button 17 to tuner on the mfc it won't work. A I am idiot? What am I doing wrong?

Gesendet von meinem HTC One mit Tapatalk
 
vistalee said:
Okay.....it kinda works. Thank you very much. I just don't want to have the tuner on 15. I want it on 17. But no matter what I do...I can't get it to work there. Although I set the tuner in the Axefx IO to 17 AND set button 17 to tuner on the mfc it won't work. A I am idiot? What am I doing wrong?

Gesendet von meinem HTC One mit Tapatalk
Click to expand...

Just making sure you know that the numbers in I/O control list on the axe do not correspond to the Switch number on the MFC.

Leave the Tuner at 15 and assign any switch on the MFC to Tuner and it will work.

I suggest leaving the entire I/O CTRL list set to default always.
 
LIST OF CC
010 Input Volume
011 Out 1 Volume
012 Out 2 Volume
013 Bypass
014 Tempo Tap
015 Tuner
016 External 1
017 External 2
018 External 3
019 External 4
020 External 5
021 External 6
022 External 7
023 External 8
024 Looper 1 Rec
025 Looper 1 Play
026 Looper 1 Once
027 Looper 1 Stack
028 Looper 1 Rev
029 Looper 2 Rec
030 Looper 2 Play
031 Looper 2 Once
032 Looper 2 Stack
033 Looper 2 Rev
034 Global Bypass
035 Volume Incr
036 Volume Decr
037 Amp 1 bypass
038 Amp 2 bypass
039 Cabinet 1 bypass
040 Cabinet 2 bypass
041 Chorus 1 bypass
042 Chorus 2 bypass
043 Compressor 1 bypass
044 Compressor 2 bypass
045 Crossover 1 bypass
046 Crossover 2 bypass
047 Delay 1 bypass
048 Delay 2 bypass
049 Drive 1 bypass
050 Drive 2 bypass
051 Enhancer bypass
052 Filter 1 bypass
053 Filter 2 bypass
054 Filter 3 bypass
055 Filter 4 bypass
056 Flanger 1 bypass
057 Flanger 2 bypass
058 Formant bypass
059 FX loop bypass
060 Gate 1 bypass
061 Gate 2 bypass
062 GEQ 1 bypass
063 GEQ 2 bypass
064 GEQ 3 bypass
065 GEQ 4 bypass
066 Megatap 1 bypass
067 MultiComp 1 bypass
068 MultiComp 2 bypass
069 MultiDelay 1 bypass
070 MultiDelay 2 bypass
071 PEQ 1 bypass
072 PEQ 2 bypass
073 PEQ 3 bypass
074 PEQ 4 bypass
075 Phaser 1 bypass
076 Phaser 2 bypass
077 Pitch 1 bypass
078 Pitch 2 bypass
079 QuadChorus 1 bypass
080 QuadChorus 2 bypass
081 Resonator 1 bypass
082 Resonator 2 bypass
083 Reverb 1 bypass
084 Reverb 2 bypass
085 Ringmod bypass
086 Rotary 1 bypass
087 Rotary 2 bypass
088 Synth 1 bypass
089 Synth 2 bypass
090 Tremolo 1 bypass
091 Tremolo 2 bypass
092 Vocoder bypass
093 Volume 1 bypass
094 Volume 2 bypass
095 Volume 3 bypass
096 Volume 4 bypass
097 WahWah 1 bypass
098 WahWah 2 bypass
 
IA switches can be assigned to Axe-Fx functions or to general MIDI functionality.
In Axe-Fx Mode go to Edit > Midi > IA and select the desired block for each switch from the list of effects. In Axe-Fx Mode IAs operate globally, meaning that you cannot change switch functionality per preset.
You can assign an effect to the switch. The switch will then enable or bypass that effect. You can also select an effect X/Y, to switch between X and Y. Other available Axe-Fx functions include Vol Inc, Vol Dec, scenes.
If you select "None", the switch is not assigned to specific Axe-Fx functionality. It will be available for general MIDI use (referred to as: General Use IA Switch). This lets you program MIDI commands. You can send 2 separate MIDI CCs, a MIDI PC, and additional custom MIDI commands per switch. Use value 127 to switch on effects, 0 to switch off. Or select OFF to send nothing at all. General Use IAs operate globally (same across all presets).
 
You must log in or register to reply here.
Back
Top Bottom