Sending some mojo for a speedy recovery! Got any recorded DI’s? You could always do some re-amping to enjoy the new firmware.Of course this comes out the day after I had surgery and won't be able to play for about a week lol.
But you know he will. I always look forward to new YouTube vids from LT. probably due to the time difference between US and Australia.It's a wonder Leon hasn't put up a Youtube yet
Got to spend an hour or so with it. Yeah, I do think the low end feels more punchy and clearer than before. Plugging into a tube poweramp and 212 cabs, there was a point where I had a sound with the D60 model that was nearly indistinguishable from my Ultra Lead Synergy module.I will be interested to hear what you think
My impressions are it is much closer to that tube preamp feel and sound
I noticed when I was playing a preset on a scene with the dual delay, and switching to a preset without a delay, I would get a weird garbled noise while the preset switched.Not sure that this is a bug it's probably just something unavoidable if I'm going to turn on gapless switching and then go and switch from a preset/scene with cab block ON to one with cab block OFF. I think it just is what it is and unavoidable but figured I'd mention it anyways...
I have a scene that I use from the Fractal Gift of Tone series from a couple years back from Fremen's preset, it's the acoustic sim scene. When you switch from any other preset or scene to that one scene in that preset without the cab block you get some pretty loud and terrible sounds for a moment while the switch is happening then it stabilizes. No big deal I'm just happy to have gapless and figure this is a case of come on don't be a dumbass dude you can't use it like THAT and not expect problems but figured why not mention it just in case it's something that can be got around somehow.
Yes I'm on the east coast and he's on the West so it's early in the morningBut you know he will. I always look forward to new YouTube vids from LT. probably due to the time difference between US and Australia.
What IR's and monitors are you using?Got to spend an hour or so with it. Yeah, I do think the low end feels more punchy and clearer than before. Plugging into a tube poweramp and 212 cabs, there was a point where I had a sound with the D60 model that was nearly indistinguishable from my Ultra Lead Synergy module.
I was looking forward to the Stealth, but also checked out the Recto 1, D60, JP IIC+, and JCM800, and they all sounded better than before. I wouldn't even use some of them before. I was surprised about that.
I still don't love it through the IRs into monitors though. I wish we had IR technology that didn't neuter the sound and feel compared to in the room, lol.
I asked basically the same thing earlier and didn't get a response but I think I found my answer...A question if I may, to all those out there who know more than me
From the FW8.0b Release Notes:
If I do the Upgrade All Presets in Setup -> Utilities on the FM3 itself, does this count as a hard reset? In other words, do I also need to do a soft reset to apply the new values?
Methinks no, but no harm in asking!
I also like the word "methinks" ... one doesn't get to use it much these days!
I was going to go back here in a few and edit my own post to reflect that and unless someone corrects me otherwise I'm going to assume the bit where Greg said "I ran upgrade all presets which pulled in all the changes..." is the answer we were looking for, that answer being if we did the upgrade all presets then we now have all new changes and available upgrades to the new firmware in effect and nothing else to do.I ran “upgrade all presets”, which pulled in the changes, then checked them for level changes and then maybe made minor adjustments to the tone controls.
I found that some of the amps sounded a little different. Cliff said that the new settings are based on different/better measurements so I attributed the difference to that; the amps are more accurate, so I wanted to recalibrate my expectations. I played using a couple different guitars and rolled their volumes to see how the amps reacted, and found some amps I’d kinda liked before that I really like now: The Bludojai Clean and Lead, and the FAS Express, are way up on my list now. I’ll give them more time and maybe change the cabs to Dyna-Cabs.
I kind of have a mess at the moment, but I have an ABY switch going into my FM3, and then my Synergy rack. The FM3 goes to a rack mixer on output 2, and a set of Kali LP6s and a JBL Sub on output 1. Basically, I can switch between all 3 situations, or use all 3 at the same time. I am running the tube stuff through a 4xKT88 poweramp that sounds pretty huge on its own. That goes into 2 oversized 212 cabs. I also have a Matrix GT1000FX, but I am not using it at the moment. I generally just pick some factory IRs that are based on 412 or 212 oversized cabs. I have considered buying some oversized Mesa cab IRs, if there is something that exists that can sound huge, and not like a recording.What IR's and monitors are you using?
I run Output 2 of my FM3 into a Powerstage 200 into a 4x12 cab with two V30's and two G12T-75's which sounds fantastic but I also run into a pair of KALI Audio LP8 studio monitors using a couple of IR's I found that I really, really like and whereas it's different than my 4x12 cab I think it still sounds equally fantastic, different for sure but still great tone.
I use the FM3's FX Loop for everything (mostly a UA Stomp for cab/mics/room mics/reverb), and no problems here with FW8.x.Thanks fro the update Fractal. Unfortunately, I'm getting squealing feedback through the FX Return/Send. Most of my presets are setup to go out to external drive pedals then back in. After updating, the unit was redlining with feedback. I tried some of the presets without the Out/In blocks and they were fine, but all of the ones utilising the FX return loop aren't ok. Hope this helps with the beta.