We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by rosleck

expression pedal issue

Just as a follow up in case any "less skilled" Axe users like myself have the same issue......after flipping the expression pedals around neither would work properly. I did the suggested reset of the MFC and the AXE & immediately the both pedals work as volume pedals now when I tried them. This...
- rosleck
- Post #15
- Mar 2, 2016
- Forum: Axe-Fx II Discussion
expression pedal issue

First thing I tried. Thanks for the assist!
- rosleck
- Post #14
- Feb 9, 2016
- Forum: Axe-Fx II Discussion
expression pedal issue

I know the feeling and yes Chris is correct. I am sure I messed up a setting somewhere at some point. Is there a factory reset type command for the 101 and Ax? I might be better off backing up my patches and trying to start fresh.
- rosleck
- Post #11
- Feb 8, 2016
- Forum: Axe-Fx II Discussion
expression pedal issue

I first moved the "bad" pedal to XP3 and attempted to calibrate it in the 101 and I received the same response. only movement from 0 to 3-4. I thne tried moving the "good" pedal and started over with the same result.
- rosleck
- Post #7
- Feb 6, 2016
- Forum: Axe-Fx II Discussion
expression pedal issue

I switched the pedals over so the "working" volume ( expression ) pedals was the wah and the non working wah was now the volume. The one of Th one of XP2 which worked on XP1 now does not work or calibrate. The non working one now works as a volume on xp1. I really think I may of dorked up a...
- rosleck
- Post #5
- Feb 6, 2016
- Forum: Axe-Fx II Discussion
expression pedal issue

After updating to quantum 2.0 today I decided to tackle an long standing issue I am having. I use a MFC 101 with 2 expression pedals. Pedal 1 is for volume and works great. Pedal 2 is for Wah and for the life of me I cannot get it to work correctly. In the 101 When I attempt to calibrate it I...
- rosleck
- Thread
- Feb 6, 2016
- Replies: 14
- Forum: Axe-Fx II Discussion
Just updated my Axe FX II to Quantum 1.06 wah not working

I am having almost the same issue. When I turn on my Wah it engages but the range on motion is very small. I tried calibrating it on the 101 and the Axe but not luck yet. Like you I had no issues before upgrading the firmware....it is possible my lack of skill at this point with the Axe help...
- rosleck
- Post #6
- Jan 11, 2016
- Forum: Axe-Fx II Discussion
Audit interface questions

Good Morning, I was hoping for a little advise on guitar audio interfaces. Since 2008 I have been using a line 6 tone port DI (main) and a tone port UX2 (backup) as my interface. When I added My Axe to the mix last year I just ran a cable from the headphone jack to the tone port line in so I...
- rosleck
- Thread
- Dec 2, 2015
- Replies: 1
- Forum: Axe-Fx II Discussion
Wah set up

Paranoid, what you said makes sense and its what I am trying to figure out how to do it. I had it working before the update.
- rosleck
- Post #5
- Sep 19, 2015
- Forum: Axe-Fx II Discussion
Wah set up

It is a expression pedal not a wah hooked into #2.
- rosleck
- Post #3
- Sep 19, 2015
- Forum: Axe-Fx II Discussion
Wah set up

I updated to Quantum and I am enjoying it. I have run into 1 odd issue my volume pedal connected into 1 on the MFC works fine. The Wah in connected to 2 in the MFC does not control the Wah. Its calibrated, but is not controlling the wah. I think I am missing a sitting but google isn't helping...
- rosleck
- Thread
- Sep 19, 2015
- Replies: 5
- Forum: Axe-Fx II Discussion
odd behavior after update

After many reboots and re attempts I managed to get it to work. The final configuration I used was 5 pin midi cable, Ethernet cable disconnected, AC power connected. After a reboot of the Axe & MFC the file was sent successfully. On the plus side after a bit of frustration I did become more...
- rosleck
- Post #11
- Mar 27, 2015
- Forum: MFC Discussion
odd behavior after update

yup it was the user again.... So I correctly hooked up the midi cable to do the receive and it worked. in the MFC EDIT I then opened the file I dumped, converted the switches and it looks OK to me on the IA switch tab. Now I cannot get the file to send back to the MFC. The Bot is sending the...
- rosleck
- Post #8
- Mar 26, 2015
- Forum: MFC Discussion
odd behavior after update

I think I have an idea on what the issue is....user again if I am right.....
- rosleck
- Post #7
- Mar 25, 2015
- Forum: MFC Discussion
odd behavior after update

Sigh..... So tonight for what ever reason I cannot get the MFC 101 ( Mark III ) to connect to the mfc edit or fractal bot. I am guessing the first step I needed to do is to send a back up of the presets to my PC. I followed the directions and no data is flowing to the PC.I have 5 5 pin midi...
- rosleck
- Post #6
- Mar 25, 2015
- Forum: MFC Discussion