Recent content by ben ifin

  1. ben ifin

    Which COMP is, or is closest to LA2A ?

    Hi all ! I did check the F/Wiki before asking :) ...but not sure In this list for FW8 beta 1 ... which COMP is, or is closest to the LA2A (?) ... I guessing / assuming its the "Optical Compressor" (?) but not sure (?) Many thanks, Ben
  2. ben ifin

    Can FM3 FSW's be set up to go Up / Down by 3 Pre-sets for each Press (?)

    Yep. Thanks :) As I suspected :( I've just now worked out a triple-all-in-one-CC command on the MC6 using FSW's F and C for Increment Up x 3 and Increment Down x 3 - its %99 there so will just go with that. Many thanks again and all the best, Ben
  3. ben ifin

    Can FM3 FSW's be set up to go Up / Down by 3 Pre-sets for each Press (?)

    Thanks heaps unix-guy ! I've just read Pages 3, 4 and 5 of the Footswitch Functions Guide ... and from what I can tell .... the Bank Up / Bank Down and Bank Size settings are only available to use with the on-board FM3 FSW's and/or the FC6 and FC12 (?) I am trying to access and trigger...
  4. ben ifin

    Can FM3 FSW's be set up to go Up / Down by 3 Pre-sets for each Press (?)

    Huge thanks ! Now to see if I can set up an external Midi FSW to do / trigger the same thing (?) ...... looks like its a no go though using an external Midi FSW (?) Thanks, Ben
  5. ben ifin

    Can FM3 FSW's be set up to go Up / Down by 3 Pre-sets for each Press (?)

    Hey all ! Apologies for all my questions but am just about done [ yes ! ] setting up my new [old] OG FM3. Quick question:- => can, say, FM3 FSW 3 be configured so that with each individual press it will go UP, say, from Pre-set 001 ... then directly to Pre-set 004 ... then directly to...
  6. ben ifin

    Looking for a Wiring Diagram ...... FM3 FASLINK II to 2.1mm 9VDC Plug ?

    Totally understood. I used the (?) for myself :) Ben
  7. ben ifin

    Looking for a Wiring Diagram ...... FM3 FASLINK II to 2.1mm 9VDC Plug ?

    Am just looking to power my MC6 MK 2 Midi FSW Controller so have emailed them to see if it is safe to run it at 12v instead of 9v. If it can, I can just solder a cable from the XLR Male to 9v Male and should all work fine :) (?) Thanks, Ben
  8. ben ifin

    Looking for a Wiring Diagram ...... FM3 FASLINK II to 2.1mm 9VDC Plug ?

    Thanks - but way too brave for me :) Ben
  9. ben ifin

    Looking for a Wiring Diagram ...... FM3 FASLINK II to 2.1mm 9VDC Plug ?

    Hi all ! Looking for a PIN Wiring Diagram to see if I can quickly make a short FasLink II Male Canon to Male 9VDC center Negative Jack ? Any links ? Many thanks, Ben
  10. ben ifin

    Amp Block => "High Treble" & "pF Cap Value" Controls ..... 2 x Quick Questions

    Many thanks ! Ben
  11. ben ifin

    Amp Block => "High Treble" & "pF Cap Value" Controls ..... 2 x Quick Questions

    Hi all ! In the Ideal Page of the Amp Block there are the 2 following settings:- Lowest Bright Cap Setting Highest Bright Cap Setting My 2 x questions are as follows:- 1 => is the High Treble dB Setting linked to the pF Bright Cap Setting (?) 2 => if I want to brighten up an Amp, is the...
  12. ben ifin

    FM3 Firmware Version 8.00 beta 1

    Much appreciated. Will do ! :) Ben
  13. ben ifin

    FM3 Firmware Version 8.00 beta 1

    Hi all ! Not at my FM3 at the moment but just had a thought about a FM3 FSW option which I would find handy. I suspect the answer is yes, but with the FM3, is it possible to 1 => set up FSW 1 so that it toggles between 2 different pre-sets back and forth on each press -and also- 2 => have...
  14. ben ifin

    Wish USB A Power Out Support .... its a lonely un-loved little Jack :(

    ...... USB A Power Out Support That little Jack has just been sitting there unused and un-loved for an awful long time now :) ... since Day 1 I think (?) Ben
  15. ben ifin

    FM3 Firmware Version 8.00 beta 1

    ...... USB A Power Out Support (?) That little Jack has just been sitting there unused and un-loved for an awful long time now :) ... since Day 1 I think (?) Ben
See more
Back
Top Bottom