danielworks
Inspired
What’s the most light pedalboard in the market that can accommodate a FC-12 and 2 expression pedals ? (Mission Engineering SP1 and Fractal EV-1)
Thank you. Would I still have space to put a 2 button footswich with this setup ?I use a Templeaudio Duo 34 for my FC-12 and the same expression pedals you use. By itself, the Duo 34 is fairly light. Adding the FC and the pedals makes it....not light.
Would you still have space for any of these big boys in your pedalboard ?I use a Templeaudio Duo 34 for my FC-12 and the same expression pedals you use. By itself, the Duo 34 is fairly light. Adding the FC and the pedals makes it....not light.
You should be good for the dual switch. I have the Temple Duo 34 and fit the FC12 and 3 expression pedals (1 Mission and 2 Dunlop) on it fine.Would you still have space for any of these big boys in your pedalboard ?
At present, no. most of the board is taken up with the FC12 and the two expression pedals.Would you still have space for any of these big boys in your pedalboard ?
A 2 button switch might fit, you'd just have to play around with the location and orientation. Securing the gear to the board can be a bit of a pain IMO. In my case, I use slightly longer screws for the FC12, and for the pedals I remove the rubber feet and secure them directly to the board with their own screws and small washers on the underside. TempleAudio makes a quick release system to use with their boards, but I've found them to be too short to work with any of the stuff I've put on the board. Plus, the adhesive for the square anchors is so strong you run the risk of tearing up the bottom of whatever gear you attach them to when you go to remove it. There are probably better/easier ways to mount gear on a pedal board but all the ones I've tried so far have some significant down sides. Won't happen I'm sure, but it would be great if FAS made some kind of pedal board specifically designed for the Fractal gear that didn't involve Velcro, or trying to find odd sized/length screws to mount gear to the board.Thank you. Would I still have space to put a 2 button footswich with this setup ?
Stupid question: what do you use to attach the pedals to the pedalboard ? Velcro, zip locks etc ?
I'd love to see this set up. I have an FC-12 arriving in 2 days. I currently have an FC-6 with 3 expression pedals (1 Mission and 2 EV-1's) on a TrailerTrash 18x30. I'm hoping the FC-12 and 3 expression pedals can all fit on my Temple DUO 34 I picked up last week.You should be good for the dual switch. I have the Temple Duo 34 and fit the FC12 and 3 expression pedals (1 Mission and 2 Dunlop) on it fine.
Check the Temple designer page:I'd love to see this set up. I have an FC-12 arriving in 2 days. I currently have an FC-6 with 3 expression pedals (1 Mission and 2 EV-1's) on a TrailerTrash 18x30. I'm hoping the FC-12 and 3 expression pedals can all fit on my Temple DUO 34 I picked up last week.
I already did that and did some real world measurements. I just thought it would be cool to see what you have there rather than a generated picture. My FC-12 comes tomorrow so I will see how it looks then.
No bother. The Temple planner is accurate, so it's a good method...I already did that and did some real world measurements. I just thought it would be cool to see what you have there rather than a generated picture. My FC-12 comes tomorrow so I will see how it looks then.
Sorry for bothering you.
Mosky Dual SwitchExcellent !
Which 2 button footswitch is it ? how did you place your pedals in this slant position ? looks tidy .
Thanks for sharing !