Marco Sfogli's presets

Although it's not advised to do this, you can unplug your Axe from the computer and then bring up the preset within Axe Edit so you can dissect all of its components.
 
i tried loading these into my G1 and they don't transfer very well, at all
 

Attachments

  • Screen Shot 2013-02-02 at 9.05.03 AM.jpg
    Screen Shot 2013-02-02 at 9.05.03 AM.jpg
    179 KB · Views: 110
  • Screen Shot 2013-02-02 at 9.05.43 AM.jpg
    Screen Shot 2013-02-02 at 9.05.43 AM.jpg
    186.3 KB · Views: 97
to do this you need to make a copy of your axe edit (and give it a unique name) and then create separate workspaces for both instances. have one set to "II" and the other set to "ultra" or "standard". you can then have both open side by side if necessary and each will load patches appropriate for the config.

don't try to use one instance of axe edit, because changing configs will empty the cache and cause you loads of problems
 
He's got the usa lead 2+ going.... One thing i found weird is he's using the 4x12 metal cab which isn't in the ii anymore. Could it be since i'm running the old edit it still shows it? Does this mean i would have to get the engl IR?
 
Ok, it looks like I'm going to have to come to konyaev's rescue. ;) I'm just going to give the settings for the "Mark V" patch (the "Modern Crunch" just has more going on in it than I'm willing to type out - 8 blocks :lol). Any settings I don't list means they are at default.

(Edit -Just realized there's a Ping-Pong delay at the end of the signal chain, so I'm editing this post to include the settings.)




Here's the signal chain:

Wah (bypassed) - Drive (bypassed) - Amp - Parametric EQ - Cab - Delay (bypassed)



WAH:

Type - Bandpass

Frequency Min - 437 Hz

Frequency Max - 1828 Hz

Tracking - 7.99



Drive

Type - T808 Mod

Drive - 0.00

Tone - 6.01

Level - 8.50

Low Cut - 167.9 Hz



Amp

Type - USA Lead 2+

Drive - 8.15

Bass - 4.28

Mid - 3.92 (Fat on)

Treble - 5.83 (Bright off)

Presence - 4.31

Depth - 3.14

Master Volume - 3.27

Supply Sag - 1.00

Input Trim - 3.308

B+ Time Const - 20.00 ms

Dynamics Time - 30.00 ms



Parametric EQ (all "Q's" are at 0.707)

Freq 1 - 76.05 Hz
Gain - 4.45 dB
Type - Shelving

Freq 2 - 239.9 Hz
Gain - 1.25 dB

Freq 3 - 747.8 Hz
Gain - 2.05 dB

Freq 4 - 2221 Hz
Gain - 1.30 dB

Freq 5 - 6720 Hz
Gain - 3.05 dB
Type - Shelving





Cab

Mode - Stereo

Cab Left - (#64) 4x12 30w (Ultra)

Mic - 57 Dyn

Cab Right - (#44) 4x12 Recto V30 (OH)

Mic - 421 Dyn

Proximity - 4.00

Pan Left - 0.0

Pan Right - 0.0

Link - Off

Motor Drive - 1.00





Delay

Type - Ping-Pong

Time - 482 ms

Feedback - 43.3

Mix - 19.7

Level - 2.5







I think that's about it. I apologize in advance for anything I may have missed, or got wrong. I used Axe-Edit, but double checked most of the settings on my Axe-Fx, so I think they are pretty much right (Axe-Edit had the Cab blocked completely screwed up).
 
Last edited:
I used snoize sysex librarian to install the patches and they sound fantastic, better than the majority of other user patches I've downloaded. I did have to adjust the levels on the amp blocks as they were clipping quite badly.
 
Back
Top Bottom