That is indeed the reason!Thanks!, so there is no way to work around those tones?
Also, these tones involve tone matching. That could also be the reason?
Tma are not converted, you have to manually convert them
That is indeed the reason!Thanks!, so there is no way to work around those tones?
Also, these tones involve tone matching. That could also be the reason?
Hey Alex, Thanks checking this right nowHi Alex,
I'm using Batch Setter with function set to "Just resave".
When I edit the field "Apply to presets", the cursor stays in that field after pressing Enter, and the button "Apply" is not operational.
There's no problem when I just leave that field at its default setting (0-511).
Ok found the bug, a lot of conversions will work better nowI think I figured out what is going on with the pitch block arpeggiator.
FracTool shows the steps in this order: Step 1, 10, 11, 12, 13, 14, 15, 16, 2, 3, 4, 5, 6, 7, 8, 9. When it converts the block it coverts step 1 like it should be, but it converts the values for step 10 as if it were step 2, step 11 as if it were step 3, (and so on) step 12 as step 4, step 13 as step 5, step 14 as step 6, step 15 as step 7, step 16 as step 8.
The conversion comes out as:
Step 1= 3
Step 2 = 24 (when it should have been 0)
Step 3 = 24 (when it should have been 3)
Step 4 = 24 (when it should have been 4)
Step 5 = 24 (when it should have been 5)
Step 6 = 24 (when it should have been 4)
Step 7 = 24 (when it should have been 0)
Step 8 = 24 (when it should have been 0)
etc.
Here is a screen shot of the pitch block arpeggiator section one of Simeon synth presets I converted.
I've already corrected the few presets I needed to by hand so I am good. I just thought this info might help you.
View attachment 59708
FracTool 3.38 is available :Hi Alex,
I'm using Batch Setter with function set to "Just resave".
When I edit the field "Apply to presets", the cursor stays in that field after pressing Enter, and the button "Apply" is not operational.
There's no problem when I just leave that field at its default setting (0-511).
Ok found the bug, a lot of conversions will work better now
- Fixes Apply button in batch setter
The cab slot you mean? YesI have not tried the batch setter yet. Is it possible with the batch setter to change the cab block for a group of presets?
If so, who do you do it? I have a bunch of presets I'd like to have the same cab block.
The cab slot you mean? Yes
No, it's a setter, not a block putter ^^I created a master cab block with my favourite 16 cab blocks in it. Channel A = 4x12 cabs for Marshalls & Freedman's, Channel B = cabs for Fender amps, Channel C = cabs for Vox, Matchless, and Morgan amps, and Channel D = Misc others.
I was wondering if I could use batch setter to load in this whole master cab block to a group of presets at a time. I've never used batch setter and don't really know what it can and can not do.
You need a whole backup with Fractal Bot@AlGrenadine
Al, I apologize for the basic question.
My goal is to transfer all of my presets and cabs from my AX8 to the AxeFxIII. However, I have to relinquish the AX8 before the the FXIII arrives.
Do I just need to backup the AX8 thru FracTool into the three basic files (System, All-Preset-Banks, All-Cabs-Banks) and then I will be able to just drop the Preset and Cab banks all at once into the FxIII? Or do I have to do something more nuanced?
Just don't want to get my FXIII and realize I didn't get the correct files from my (already gone) AX8.
Gotcha, thanks Al.You need a whole backup with Fractal Bot
Because you need to update your axefx firmwareAfter downloading the latest update (Ver 3.38) and using with Axe Edit III version 1.03.10, I cannot get any presets to send to the Axe III. The preset just shows all blank blocks, irrespective of what preset I'm trying to send (XL+, AX8, etc). Any workaround for this?View attachment 60369
On it, thanks! (dumb move on my part).Because you need to update your axefx firmware
Drop preset banks on the hard-drive icon, then click the top-left menu in the bank window to save as Axe-fx-3 format.Hey there - just got my AxeFx III and want to convert all of my AX8 Band presets. I think FracTool is the perfect way to go
How can I convert custom scales for the Harmonizer? This is not automatically done, right? What about user cabs? Are they converted automatically?
Thanks for your help
How are you feeling brother? Was just thinking about our Fractal friends having health issues..having been thru some myself...but I’m optimistic and feeling good and wishing the same for all of us.Drop preset banks on the hard-drive icon, then click the top-left menu in the bank window to save as Axe-fx-3 format.
Do the same thing for cab banks.
Then use FractalBot to send the presets then the cabs.
No, custom hatmonizer scales are in the system bank which cannot be converted