• We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

    Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

teddis

Fractal Fanatic
A great video ! I look forward to exploring this preset ! Thank you.
Was this with 104 and Economy Reverb ? Wondering if we can squeeze a COMP in now ;)
cheers !
 

yek

Moderator
Moderator
Great sounds.
  • Pitch > Quad Detune takes up a lot of CPU. You can perhaps reduce it to Dual Detune to save some.
  • You can delete the OUT 2 block, and set "Output 2 Copy" to "OUT 1" in I/O.
  • You have the Cab right after the Amp block, so it can be mono. Use Cab-Lab to mix the two IRs into a single one. Saves a couple percent points.
 
Great sounds.
  • Pitch > Quad Detune takes up a lot of CPU. You can perhaps reduce it to Dual Detune to save some.
  • You can delete the OUT 2 block, and set "Output 2 Copy" to "OUT 1" in I/O.
  • You have the Cab right after the Amp block, so it can be mono. Use Cab-Lab to mix the two IRs into a single one. Saves a couple percent points.
Great points!!! You're the man!
 

yeky83

Power User
Whoa, using the amp control switches for drive/EQ means the bypass state carries over multiple scenes... never thought of that before. I might make use of scenes more often now. Always wanted a way to separately control drive/EQ bypass states while controlling the time-based effects with scenes.
 
Whoa, using the amp control switches for drive/EQ means the bypass state carries over multiple scenes... never thought of that before. I might make use of scenes more often now. Always wanted a way to separately control drive/EQ bypass states while controlling the time-based effects with scenes.
Yeah!! Honestly, one of my favorite things was when FAS added the ability to tweak the input boost on the amp block. That changed the game! I wish the AX8 had that too. It frees you up from using a drive block, and if you just add a clean boost pedal in front of the FM3, you are good to go!
 

Moke

Axe-Master
Vendor
Hey Milo, try this out...
  • Replaced the Reverb block with a Delay block acting as a Reverb. Set it up to approximate your verb channels.
    Channel A, 'Plate'
    Channel B, 'Spring'
    Channel C, 'Cathedral'
    Channel D, 'Plate/Room?' with more pre-delay. (not used in any scenes, but added for the heck of it)
  • Changed the 'Pitch' block to 'Dual-Detune' (added a little modulating to thicken it)
Enough CPU left for two Compressors, a Drive, a Phaser, and maybe a Flanger (or whatever?) if you get rid of the Out 2 block and use 'Output 2 Copy' as Yek mentioned?

Moke
 

Attachments

  • MILO Preset (MCP).syx
    24.1 KB · Views: 128
Hey Milo, try this out...
  • Replaced the Reverb block with a Delay block acting as a Reverb. Set it up to approximate your verb channels.
    Channel A, 'Plate'
    Channel B, 'Spring'
    Channel C, 'Cathedral'
    Channel D, 'Plate/Room?' with more pre-delay. (not used in any scenes, but added for the heck of it)
  • Changed the 'Pitch' block to 'Dual-Detune' (added a little modulating to thicken it)
Enough CPU left for two Compressors, a Drive, a Phaser, and maybe a Flanger (or whatever?) if you get rid of the Out 2 block and use 'Output 2 Copy' as Yek mentioned?

Moke
Badass!!!!!!!!!!!! Check it out @Rafa Diaz
 

Rafa Diaz

Experienced
Great sounds.
  • Pitch > Quad Detune takes up a lot of CPU. You can perhaps reduce it to Dual Detune to save some.
  • You can delete the OUT 2 block, and set "Output 2 Copy" to "OUT 1" in I/O.
  • You have the Cab right after the Amp block, so it can be mono. Use Cab-Lab to mix the two IRs into a single one. Saves a couple percent points.
Following that advice I presume you refer to cab lab paying version?
Does it allow you to mix factory IR as well or only external user ones?
Thanks
 

yek

Moderator
Moderator
Following that advice I presume you refer to cab lab paying version?
Does it allow you to mix factory IR as well or only external user ones?
Thanks

Only external, so you must own the appropriate cab pack.

PS I’d love a way to mix multiple factory cabs into a single one, in the hardware.
 
Top Bottom