USMC_Trev
Axe-Master
Well you kinda have to...That is like using Internet Explorer to download Chrome!
Well you kinda have to...That is like using Internet Explorer to download Chrome!
I can corroborate this. literally every preset now has Compression set to 69.9% wthout FM3-Edit, on the front panel. importing old presets also have this setting. I have never touched this parameter before.You must've set it to 69.9. Mesas don't have cathode followers so the default value is zero.
If you reset the amp block it will go to the default settings.I can corroborate this. literally every preset now has Compression set to 69.9% wthout FM3-Edit, on the front panel. importing old presets also have this setting. I have never touched this parameter before.
That's a bug. I've notified engineering.I can corroborate this. literally every preset now has Compression set to 69.9% wthout FM3-Edit, on the front panel. importing old presets also have this setting. I have never touched this parameter before.
Is there a bug report up? I am troubleshooting as I type. Maybe we can take this issue there so other stuff can be discussed here?If you reset the amp block it will go to the default settings.
I'll let you know if I figure out anything. You kick assThat's a bug. I've notified engineering.
Nope but I’ve always had the bass dialled back on the mixer. No change from 3.0 to my ears.Is anyone else finding 3.0 super bassy
also on some amps like the Archon bright, DZL VH the treble control does not really seem to do a lot to brighten it up , presence to Is very subtle through the range
I need to do a post on this but there is an easy fix to that per-preset that I've done for many years. Go to the input EQ block and do a high pass on just the input. I use 100Hz a lot on heavier amps as a starting point. Just depends on the guitar. You'll have all your low end but it'll be controlled and just sound better. Trust me.Is anyone else finding 3.0 super bassy
also on some amps like the Archon bright, DZL VH the treble control does not really seem to do a lot to brighten it up , presence to Is very subtle through the range
If you reset the amp block it should be super unbassy.Is anyone else finding 3.0 super bassy
also on some amps like the Archon bright, DZL VH the treble control does not really seem to do a lot to brighten it up , presence to Is very subtle through the range
Tnx Chris, I receive FM3 a few days ago with FW2. My main patch have 3 scenes, each one has a boosted one. So 6 scenes. I set the switch with current and the display and colors of the switch were diffent as expect (green clean, yellow crunch, red lead). Now all switch has the same colour. I am not sure if v2 behaviour was an unintentional bug, but that suit me well showing the current state of the switches, active or not.Current has always worked that way for Scenes. It makes the switch display the currently selected Scene. If multiple Scene switches are set to Current, they’ll all show the same thing: the currently selected Scene.
Current does not show “the currently selected Scene if that Scene is controlled by that switch, but the Destination Scene if the Current Scene is not controlled by that switch.”
I need to do a post on this but there is an easy fix to that per-preset that I've done for many years. Go to the input EQ block and do a high pass on just the input. I use 100Hz a lot on heavier amps as a starting point. Just depends on the guitar. You'll have all your low end but it'll be controlled and just sound better. Trust me.
Hardness and Grid Clipping should be 0 and 30 respectively. Compression is wrong. I've notified engineering but it's the weekend and they won't get to it until tomorrow.I've noticed that with 3.00 in all my saved patches now, if you go on the section "Dynamics" on the Amp block that uses "Plexi 100W 1970", I have
Compression: 69.9 %
Hardness: 0.00
Grid Clipping: 30.0 %
instead of the previous defaults
Compression: 77.4 %
Hardness: 7.50
Grid Clipping: 50.0 %
in "Power Tube Type" I have "EL34" instead of "EL34/6CA7" and in the "Tube Compressor" now I have
Attack Time: 0.283 ms
instead of
Attack Time: 2.000 ms
All the other settings are exactly the same as before
When I started FM3 edit the next time it loaded all banks from the start
How does one reset the amp block? Delete it and put it back in?If you reset the amp block it will go to the default settings.
Jeezus, Yek, is there anything you don’t know? Thanks man.