www.fractalaudio.com/downloads/firmware-presets/axe-fx-3/1p0/axefxiii_dsp_rel_1p17.zip
Fixes the issue with 1.16.
Axe-Fx III Firmware Release Notes
1.17
Fixed NaN when selecting “USA” amp types.
1.16
Improved Multiband Compressor block so that mid-band gain is automatically compensated for crossover response.
Added Frequency Range parameters to Multiband Compressor block. This selects between Low and High frequency ranges yielding more flexible crossover frequencies.
Added Crossover Slope parameter to Multiband Compressor block. Choices are 12 and 24 dB/octave.
Added FAS Boost to Amp block input boost types.
Added Output Mode to Amp block. The default value, FRFR, is the classic mode and designed for use with monitors or recording. The SS PA + Cab mode is intended for use with a solid-state power amp and conventional guitar cab. In this mode speaker compression modeling behaves differently relying on the speaker for compression while still simulating the interaction with the power amp. NOTE: this mode is not intended for use with current drive power amps, i.e. tube power amps, Class-D current feedback amps (Quilter Tone Block), etc. NOTE: this mode CAN be used with FRFR monitors in high volume applications where the monitor’s speakers are compressing thereby achieving a more dynamic response.
Added 10-band, 2/3 octave types to Graphic EQ block. These types center the filter frequencies on a narrower range best suited to finely sculpting guitar tones.
Added 10-band, 2/3 octave graphic equalizer to Drive block. The EQ can be enabled/disabled via the Graphic EQ parameter which is also modifiable.
Added 8-band, 2/3 octave graphic equalizer to Wah block. The EQ can be enabled/disabled via the EQ parameter which is also modifiable.
Fixed moving cabs with Axe-Edit causes corrupted empty slots.
Fixed Looper status not reported correctly via MIDI.
Fixed Looper doesn’t always start if threshold is off.
Fixed metronome turning on when executing Reset System Parameters.
Various fixes and changes for FC series foot controllers.
Fixes the issue with 1.16.
Axe-Fx III Firmware Release Notes
1.17
Fixed NaN when selecting “USA” amp types.
1.16
Improved Multiband Compressor block so that mid-band gain is automatically compensated for crossover response.
Added Frequency Range parameters to Multiband Compressor block. This selects between Low and High frequency ranges yielding more flexible crossover frequencies.
Added Crossover Slope parameter to Multiband Compressor block. Choices are 12 and 24 dB/octave.
Added FAS Boost to Amp block input boost types.
Added Output Mode to Amp block. The default value, FRFR, is the classic mode and designed for use with monitors or recording. The SS PA + Cab mode is intended for use with a solid-state power amp and conventional guitar cab. In this mode speaker compression modeling behaves differently relying on the speaker for compression while still simulating the interaction with the power amp. NOTE: this mode is not intended for use with current drive power amps, i.e. tube power amps, Class-D current feedback amps (Quilter Tone Block), etc. NOTE: this mode CAN be used with FRFR monitors in high volume applications where the monitor’s speakers are compressing thereby achieving a more dynamic response.
Added 10-band, 2/3 octave types to Graphic EQ block. These types center the filter frequencies on a narrower range best suited to finely sculpting guitar tones.
Added 10-band, 2/3 octave graphic equalizer to Drive block. The EQ can be enabled/disabled via the Graphic EQ parameter which is also modifiable.
Added 8-band, 2/3 octave graphic equalizer to Wah block. The EQ can be enabled/disabled via the EQ parameter which is also modifiable.
Fixed moving cabs with Axe-Edit causes corrupted empty slots.
Fixed Looper status not reported correctly via MIDI.
Fixed Looper doesn’t always start if threshold is off.
Fixed metronome turning on when executing Reset System Parameters.
Various fixes and changes for FC series foot controllers.
