Axe-Fx III Firmware Version 1.16

Status
Not open for further replies.
Let me try the Mesa patches...... Petrucci patch was the one that started the issues for me. Confirmed. I went back to the Brown Sound patch and rebooted and all is good again.
 
Just to confirm I built a basic patch with (Input 1----Amp-----Cab-----Out 1). As soon as I changed it to USA Clean the error occurred.
 
I went back to 1.16 and I switched the Mesa patches off the USA Clean #237 but still have the issue. I tried several different amps. However, I tried your test and built a simple patch which worked. As soon as I switched to #237 the error occurred.
 
I'm at work at the moment but can confirm that when I updated to 1.16 this morning, the bug happened for me as well. All active output LEDs are lit solid. Changing patches produced loud pops.
 
FractalAudio said:
[EDIT] Deleted as some users are experiencing issues.
Click to expand...

Hi there, I am new here!
Just received my new Axefxiii in the mail today, I seem to be unable to connect to the Axe-Edit III software because it tells me I need firmware version 1.16!

I then read a little on the forum here and it seems that that is on pause for now?...
What then should I do to get connected to the editor?

Thanks
very excited to figure this thing out!

Jake
 
JacobiusWrex said:
Hi there, I am new here!
Just received my new Axefxiii in the mail today, I seem to be unable to connect to the Axe-Edit III software because it tells me I need firmware version 1.16!

I then read a little on the forum here and it seems that that is on pause for now?...
What then should I do to get connected to the editor?

Thanks
very excited to figure this thing out!

Jake
Click to expand...
They released a beta a few days ago that worked fairly well, but when they fixed a couple of small issues it made some major issues for many users in the release. Most of us are using that beta version without any major issues:
https://forum.fractalaudio.com/threads/axe-fx-iii-firmware-version-1-16-beta-2.143220/
 
Genghis said:
They released a beta a few days ago that worked fairly well, but when they fixed a couple of small issues it made some major issues for many users in the release. Most of us are using that beta version without any major issues:
Click to expand...

Awesome, updating now, thank you!
 
FractalAudio said:
Axe-Fx III Firmware Release Notes

1.16

Graphic EQ block. These types center the filter frequencies on a narrower range best suited to finely sculpting guitar tones.

Added 10-band, 2/3 octave graphic equalizer to Drive block. The EQ can be enabled/disabled via the Graphic EQ parameter which is also modifiable.

Added 8-band, 2/3 octave graphic equalizer to Wah block. The EQ can be enabled/disabled via the EQ parameter which is also modifiable.
Click to expand...

Huge. Big.
 
FractalAudio said:
Axe-Fx III Firmware Release Notes

1.16

Improved Multiband Compressor block so that mid-band gain is automatically compensated for crossover response.

Added Frequency Range parameters to Multiband Compressor block. This selects between Low and High frequency ranges yielding more flexible crossover frequencies.

Added Crossover Slope parameter to Multiband Compressor block. Choices are 12 and 24 dB/octave.

Added FAS Boost to Amp block input boost types.

Added Output Mode to Amp block. The default value, FRFR, is the classic mode and designed for use with monitors or recording. The SS PA + Cab mode is intended for use with a solid-state power amp and conventional guitar cab. In this mode speaker compression modeling behaves differently relying on the speaker for compression while still simulating the interaction with the power amp. NOTE: this mode is not intended for use with current drive power amps, i.e. tube power amps, Class-D current feedback amps (Quilter Tone Block), etc. NOTE: this mode CAN be used with FRFR monitors in high volume applications where the monitor’s speakers are compressing thereby achieving a more dynamic response.

Added 10-band, 2/3 octave types to Graphic EQ block. These types center the filter frequencies on a narrower range best suited to finely sculpting guitar tones.

Added 10-band, 2/3 octave graphic equalizer to Drive block. The EQ can be enabled/disabled via the Graphic EQ parameter which is also modifiable.

Added 8-band, 2/3 octave graphic equalizer to Wah block. The EQ can be enabled/disabled via the EQ parameter which is also modifiable.

Fixed moving cabs with Axe-Edit causes corrupted empty slots.

Fixed Looper status not reported correctly via MIDI.

Fixed Looper doesn’t always start if threshold is off.

Fixed metronome turning on when executing Reset System Parameters.

Various fixes and changes for FC series foot controllers.
Click to expand...
Hell yeahhhhh!!!! Thanks!!!!
 
Status
Not open for further replies.
Back
Top Bottom