• We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

    Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Axe-Fx Firmware Release Version 17.01 Release Candidate

Status
Not open for further replies.

Cpt737

Member
Everything sounds quite to me after the installing the 17.01. I use a matrix power amp and a 2x12 evh cab (didnt touch the levels) . All my presets' volume dropped significantly. Did I miss any release note or something?
 

deathbyguitar

Power User
Everything sounds quite to me after the installing the 17.01. I use a matrix power amp and a 2x12 evh cab (didnt touch the levels) . All my presets' volume dropped significantly. Did I miss any release note or something?
When I installed the last beta, it reset a bunch of system settings to their defaults including the output levels. You might have had inputs 1/2 set to +4 instead of -10 which it defaults to.
 

Cpt737

Member
I/O > Audio > Output .. Level
Yep that was it. They went back to -10 db. Also now I realise my Behringer FCB1010 midi pedal settings are gone which was a pain in the ass to program. I assume It will we go back to normal with the official release.
 

unix-guy

Legend!
Yep that was it. They went back to -10 db. Also now I realise my Behringer FCB1010 midi pedal settings are gone which was a pain in the ass to program. I assume It will we go back to normal with the official release.
Did you perform a system backup before updating? If so, restore it...

System settings are not expected to change during a FW update and any future update would have no idea what settings you had before, so they won't "go back".
 

Cpt737

Member
Did you perform a system backup before updating? If so, restore it...

System settings are not expected to change during a FW update and any future update would have no idea what settings you had before, so they won't "go back".
I did not just before updating but I have an older backup from 16.05. So I downgraded to that and now the midi pedal works as it suppose to. So the question is how do I translate current midi settings to 17.01?
 

unix-guy

Legend!
I did not just before updating but I have an older backup from 16.05. So I downgraded to that and now the midi pedal works as it suppose to. So the question is how do I translate current midi settings to 17.01?
I think you can just go to 17.01 and then restore only the system settings...

Otherwise, I'm not sure.
 

luke

Fractal Fanatic
Cannot get this to load, stops at 2.6% each time.

Yes I redownloaded it twice more, turned everything off and back on.
 

unix-guy

Legend!
Cannot get this to load, stops at 2.6% each time.

Yes I redownloaded it twice more, turned everything off and back on.
Are you using standalone FractalBot or the one embedded in Axe-Edit?

If standalone, make sure Axe-Edit is closed, otherwise make sure the standalone FractalBot is closed.

Try a different USB cable and port.
 

TSJMajesty

Power User
Cannot get this to load, stops at 2.6% each time.

Yes I redownloaded it twice more, turned everything off and back on.
No problems here. After I backed up everything, I updated Axe Edit to the prompted version, then to 1.10.03 from the update thread. Updated Axe last. Not sure if it matters, but after each step, I restart Edit, and make sure it works fine.
USB cable 5m or less? Set Axe to empty preset?
 

FlavAnderson

Inspired
@FractalAudio. Looking at my contributions to the new types in the multitap delay, there are some issues with the the 1210 type. The fitler Q on the individual filters isn't set to the minimum value, which alters the frequency response and makes the tone kinda muddy. The sweep of the chorus isn't wide enough, since I didn't use auto depth when I created my replica. Might be able to just bump up the value to get it more in the ball park.

I also noticed the new parameters related to the diffusion. Sounds much better with them! I plan to do a deep dive tomorrow and see which settings are closed to the actual PCM70.
Where do I find the 1210 type in the Multi Tap Delay Block?
 
Status
Not open for further replies.
Top Bottom