Search results for query: *

  1. Petrocelli

    FM3 Firmware Version 8.00 beta 1

    Bias Trem was never in the FM3 Amp Block, only in the Greater Brothers Blocks (AxeFX + maybe FM9 have this) Its an FM3 Edit issue like also the Plate Reverbs have non corresponding controls…
  2. Petrocelli

    FM3-Edit 1.06.08 (to support fw 8.00 public beta)

    Workaround: When i put a unconnected Out2 Block in the Grid the displayed Level goes away. I can delete the Block and the Preset Leveling Display shows no signal anymore as it should. Forgot to say: Setup - Audio - Output config Output 2 Copy setting is "Output 1"
  3. Petrocelli

    FM3 Firmware Version 8.00 beta 1

    possible Bug in the Tremolo Block: - Optical Trem 1&2 are about 9dB quiter than all other Trem Types with identical settings! Fantastic Update! Gapless Switchig is so good and Cygnus 3 and the new amps and drives are killer! Thank you so much dear FAS Team for this milestone.
  4. Petrocelli

    FM3-Edit 1.06.08 (to support fw 8.00 public beta)

    Some small Bugs: In the preset Leveling window Output 2 is showing a constant level of -4.5dB on all Presets even with no Signal is coming in! The Reverb Block have controls in the Plate and Spring Verbs that ar not in the Hardware Parameter List and dont have an audible function. Thank you...
  5. Petrocelli

    Axe-Fx III Firmware 25.00 Public Beta #2 (Cygnus X-3 Release Candidate)

    Today I built another bass preset. In addition to other drives, I like to use the B7K pedal. A while ago I noticed that the "Mix" parameter in some drives wasn't working properly (B7K, all fuzz pedals, 3+4 Knob Tube Driver, Shimmer Drive, etc.), so i had to do a Vol Block in Parallel with these...
  6. Petrocelli

    Axe-Fx III Firmware 25.00 Public Beta #2 (Cygnus X-3 Release Candidate)

    Defnetly - you can get funny crazy Ring Modulator Fuzzy Tones out of it with extreme settings. (Hi rates for Supply Sag, Screen Frequency and Screen Q, Low setiings for B+ Time Constant). I like it to experiment with those broken Amp sounds.
  7. Petrocelli

    Axe-Fx III Firmware 25.00 Public Beta #2 (Cygnus X-3 Release Candidate)

    Bug? I just noticed that the "Neon Trem" only works in mono. Adjusting the LFO phase has no effect between the left and right channels like all other tremolo types. I know the tremolo block wasn't touched in this update, but it probably wasn't noticed until now.
  8. Petrocelli

    Bug? (Possible) in 25.00 beta Impedance Curve Selection

    Had a similar experience with a nearly flat impedance Curve in a Dynacab Preset and the 25.00 Beta Version. But since i updated to the actual Axe Edit version 1.13.18 i thought its ok, but didn‘t spend much time with it!
  9. Petrocelli

    Axe-Edit III 1.13.17 (to support fw 25.00 public beta)

    Wow, so fast! Thank you so much. Mute and Solo are working normal now!
  10. Petrocelli

    Axe-Edit III 1.13.16 (to support fw 25.00 public beta)

    Strange behaviour with the Mute and Solo Buttons in the Cab Block - its not possible to deactivate them! I dont see a change with the Buttons in the two Sunrise Splendor Modells to the 1.13.15 version - is that correct?
  11. Petrocelli

    Fractal Noise Reducer vs noiseless single-coils

    I use Fishman Fluence low impedance Single Coils PUs in a Tele and in a Strat and totally happy with them. Not absolutely noiseless but way more than a normal high impedance PU! Also no treble loss when lowering the Volume Pot and the possibility to switch to different Sounds.
  12. Petrocelli

    BlueAmps Cabinets

    I've now rehearsed twice with the Cubo EX, it really doesn't sound bad, has enormous pressure and is pretty loud. Nevertheless, the upper 1-2 octaves of the spectrum are a bit underexposed (which I'm sure many guitarists love). But I wanted a speaker that would give me roughly the spectrum of a...
  13. Petrocelli

    FM3 Firmware Version 7.00

    You don't know this technique? :tearsofjoy:
  14. Petrocelli

    BlueAmps Cabinets

    I bought a used Cubo EX on eBay. Looks like new and comes with 3-band EQ and protective case. I also ordered a speaker tilter so that it plays into my ears and not into the back of my knees. I first tested them in my home studio and compared them with my active NUBERT nuPro A300 monitors (German...
  15. Petrocelli

    Axe-Fx III Firmware 24.05 Release

    As i remember, the Air Frequency is a Hi cut Filter! Also a Lo cut would be helpful to only bring some realy Air Frequencys in (Maybe 8 - 15KHz) Delay or alligned dry signal would also be cool!
  16. Petrocelli

    yes I said banjo

    If you can grab a Line6 Variax, it has also a satisfying Banjo included. (Never played a real Banjo), I have a James Taylor JTV-59 and like it as a totally flexible Guitar!
  17. Petrocelli

    Implemented Smoothing for Random LFO

    The Axe FX III has a „High Cut“ parameter in the LFO 1+2 section. This smoothes out the edges on the „Random“ and other waveforms. I think its also in the FM3
  18. Petrocelli

    FM3, S/PDiF and Multiple Outputs

    SPDIF can carry two channels. If your wet signal is stereo thats two channels! I think there will be a minimum amount of latency between analog out and SPDIF, because the analog signal has to be converted to digital, but you have to try!
  19. Petrocelli

    8x10 Dynacab Update??

    Yes, i also hope with every new firmware the inclusion of the announced 8x10“ SVT cab!
  20. Petrocelli

    Hearing Crackling/distortion from DAW and computer sound since last update?

    Try to feed the Axe FX lll SPDIF out as clock source to the Apollos SPDIF in. (you need a cheap coax to opto converter). Clock Apollos sync to external clock und try if it works.
  21. Petrocelli

    Low output volume

    Which Cables do you use? Sym XLR on Out1? Out 2 has Humbuster outputs (see the Manual), they are NOT symmetrical TRS connected!
  22. Petrocelli

    Low output volume

    ...and you turnd up the physical Output Level Knobs? FM3 has (too)much Output Level when turned up completely for all of my gear!
  23. Petrocelli

    Axe-Fx III Firmware 24.02 Release

    After a short test all works perfekt. I love the overworked Brit Silver, sounds very smooth! Also the Bug in the Tape Delays with engaged Compander is fixed - perfekt! So all i hope is now a little love for my FM3, so it gets also some of the goodies! Again a big thank you for your great work...
  24. Petrocelli

    Some new presets from me for download

    I have Downloaded and Donated, Merry Christmas and have a better 2024 than 2023!
  25. Petrocelli

    Axe-Fx III Firmware 24.02 Beta #1

    I tried your preset and yes, in scene 1 there is a more feedback as it should be. I did a soft reset with the delay block, dialed your settings back and it was normal. Then i realised that you switched the compander on and that is now the issue with all tape based delays i found out. If the...
  26. Petrocelli

    Axe-Fx III Firmware 24.02 Beta #1

    Thank you for the lightning fast fixses - did a short trial and all works best for me. The Stack/hold function is awsome. So i have to thank the whole Fractal Team for this great support all over the year, relax and a nice Christmas to everyone!
  27. Petrocelli

    Axe-Fx III Firmware 24.01 Release

    I also noticed the ping-pong delay problem. If you load the Ping Pong Type, only a mono delay can be heard. Only when you change the L/R time ratio, e.g. 50%, does the usual effect become audible. For comparison, I tested the same settings on my FM3 (FW 7.0) and here Ping Pong works as usual...
  28. Petrocelli

    Fixed Block erroneously displayed in the wrong place

    Had the same thing happen yesterday with my FM3 Edit. It was a single Plex Delay Block in the Grid and i couldn‘t delete it. But i could change it to a Filter Block and then delete!
  29. Petrocelli

    Axe-Fx III Firmware 24.00 Public Beta #2

    Thank you, that was the Problem! But shouldn‘t the MV controls be visible in both views? …maybe in the final Version?
  30. Petrocelli

    Axe-Fx III Firmware 24.00 Public Beta #2

    "Added Global MV control to JS410 amp models. Master Volume has been renamed Channel MV. These two master volume controls can be used to balance the tone into the power amp (as in the real amp). The Channel MV decreases the high frequencies as it is turned down whereas the Global MV is...
  31. Petrocelli

    Axe-Fx III Firmware 24.00 Public Beta #2

    Thank you, i didn't know this, that helped! I just looked to (non updated) Axe Edit-Setup-Audio Menue! But maybe it's possible to add a small clock state icon near the global tuning triangles?
  32. Petrocelli

    Axe-Fx III Firmware 24.00 Public Beta #2

    I tested Wordclock internal and external Modes and had no Problems with either configurations! Tested wit my RME AIO and all works fine! If i disconnect the digital input in WC Mode "SPDIF" the unit mutes for one Second and than Signal is there (unit switches to internal clock). Also with my UAD...
  33. Petrocelli

    Dyna-Cabs Version 1.05

    Yes, i hope we will get that announced 8x10“ Cab sometimes because my bass feels 🥹😂
  34. Petrocelli

    Axe-Edit III 1.13.10

    Perfect!
  35. Petrocelli

    Axe-Fx III Firmware 23.03 Beta #1

    Maybe a little out of context, but since @Cliff also maintains the Drive models (DS1 potentiometer characteristic, new drives) it would be great to fix the mixer functionality in the Drive Blocks for certain types. It affects the: B7K, all fuzz pedals, FET Pre, mid-boost, SSD...
  36. Petrocelli

    Axe-Fx III Firmware 23.02 Release

    Yes, it's a realy low level but i never had a chance to play the real thing! So maybe it's authentic, i don't know?
  37. Petrocelli

    Cab block: Preamp Tone Controls vs High / Low Cut?

    I use the BMT of the preamp a lot - mostly with DynaCabs. I like the Mids, but it would be more useful with a tunable frequency (parametric mids). Also usable if it could be decoupled from the preamp section! The use of a seperate EQ block dont help me so much, because i like to save the cabs in...
  38. Petrocelli

    Axe-Fx III Firmware 23.02 Release

    In the 2290 algo, one of the channels is phase inversed for a very wide sound! If you try to hear this in mono, you hear nothing of the repeats because of phase canceling! Use Stereo Headphones or a stereo speaker system!
  39. Petrocelli

    Axe-Edit III 1.13.09

    Hi Michael, thank you very much for this fast update! I like the new waveform display for the LFO section in the phaser! It would be great to have this Display also in the other LFO sections e.g. in the flanger, chorus… or also in the modifier LFO section. Have a nice weekend Tom
  40. Petrocelli

    Axe-Fx III with E-bow

    Use a Filter Block with a Lowpass Filter after the input! Frequency to taste (start with about 2 KHz)
  41. Petrocelli

    Axe-Fx III Firmware 23.00 Release

    Sorry, it was my fail - Quantize Parameter in the LFO's works correct - shame on me:grimacing:
  42. Petrocelli

    Axe-Fx III Firmware 23.00 Release

    Here is a simple Preset: Scene 1 Phaser with Step Quantisize, Scene 2 Flanger with Step Quantisize Scene 3 Filter - Filterfreq with ext. LFO1 modulated, Step Quantisize enabled, but in all this Scenes Quantisize in the modulation isn't audible!
  43. Petrocelli

    Axe-Fx III Firmware 23.00 Release

    potential Bug?: I'm not able to get "Stepped Flanger/Phaser" Sounds anymore - or do i something wrong? Like in the Manual: "LFO Quantize – This control allows “stepped” effects in which the smooth shape of the LFO is transformed into a series of flat stages similar to those heard when a “sample...
  44. Petrocelli

    Axe-Fx III Firmware 23.00 Release Candidate #2 (Beta #7)

    Can also confirm random weird modulations in Cumulonimbus Reverb and non working Rotary Block! Thank you for the New Opto Tremolos. Is the "Neon Trem" realy such a pronounced Effekt in the Blackfaces? I never had the real thing!
  45. Petrocelli

    FM3 Controlling Looper With Just 3 Switches?

    You can add up to 4 stand in switches on the two pedal jacks at the backside. So you have more opinions with some cheap footswitches. Best use momentary switches.
  46. Petrocelli

    Axe-Edit III 1.13.05 (to support fw 23.00 public beta 4)

    Thanks very much - much more fun to edit the Reverbs. Small Bug: As mentioned by Cliff the Spring reverbs don't have modulation possibilitys anymore (as in the Hardware), so i think the Modulation Knobs in the Mod+Ducker section could be removed!
  47. Petrocelli

    FM3 Out 2 Clip Led when copy Output 1

    Ah the big 4 Speaker Version! How is the Stereo Sound out from one Cab? (Reverb, Delays, Chorus...)? Im thinking about buying this or two normal cubos! Its nice that you tell its near the KH120 - i like them. I was already in contact with Marco, but it is nice to hear a opinion from a user.
  48. Petrocelli

    Axe-Fx III Firmware 23.00 Public Beta #4

    Yes, thats the virtual Capo in this Scene!
  49. Petrocelli

    Axe-Fx III Firmware 23.00 Public Beta #4

    Is this normal? When i switch the "Quality" between Ultra-High and Economy in the Reverb Block there is only a CPU difference about 3 - 5%! Also i dont hear a big difference.
  50. Petrocelli

    Axe-Fx III Firmware 23.00 Public Beta #4

    The Plate Reverbs sound wonderful - cant stop playing the Gold Plate. Had myself a EMT240 Gold foil 25 Years ago (which was very noisy) and now its back and absolute clean - wonderful! The switchable Pre Delay Tap to "Input" is extremely useful for me without the gap in the "Output" setting...
  51. Petrocelli

    FM3 Out 2 Clip Led when copy Output 1

    Servus Heilsbringer, Maybe you are clipping the Input of the Cubo? I always use the Preset Leveling Tool in FM3 Edit to have enough headroom (try not to reach more than 0dB in the meters) If the Level is good there, i had never a Problem with a clipped Output even the Level Pots are fully open...
  52. Petrocelli

    CabLab 4

    You can load up to 4 DynaCabs / IRs, mix it down to a IR und put it in the UserCab Slots. So loading this IR needs the same resources as any other IR you use!
  53. Petrocelli

    Cab-Lab 4 Version 1.00.01 Release

    Just put my FM3 out of the bag and tried SW Mode - here it works! patched back to AxeFx III und Problem is here again! So i think its a problem with the actual AxeFX beta!
  54. Petrocelli

    Cab-Lab 4 Version 1.00.01 Release

    Just Loaded Cab-Lab 4 1.00.01on my Win10 PC and bought two DynaCabs! Set Up everything as described but SW Live Mode is not working - HW Manual Mode works, but isn't very intuitive to always push the send button. Maybe a switchable automatic Mode which sends after stopping mouse action? I tried...
  55. Petrocelli

    Axe-Fx III Firmware 23.00 Public Beta #2

    Yes i know, with stereo spread we can dial in the amount of the „side“ part of a stereo signal, from mono (0%) to stereo (100%) and beyond (100%+). But if a Block Type Output is Mono, this parameter is doing nothing. I know also the trick to use two blocks in parallel to get a stereo Spring...
  56. Petrocelli

    Axe-Fx III Firmware 23.00 Public Beta #2

    I like the new spring Reverbs - very tasteful. Sadly they are all Mono. A long Time ago i had a AKG BX15 Spring Reverb, this could be used in 2Ch/Stereo and maybe its possible to turn e.g. the Studio Spring Type etc. in to a stereo algo, that would be very nice. Also there is a Stereo Spread...
  57. Petrocelli

    Cab-Lab 4 Release 🔈🧪

    Maybe a Bug: Installed Cab-Lab 4 with no Problems untill i tried to test the vst3 Plugin in Cubase Pro 12 - it wasn't there! It wasnt either in the default vst3 Path: "C:\Program Files\Common Files\VST3" nor in the Program path: "C:\Program Files\Fractal Audio\Cab-Lab 4" I found it in my old...
  58. Petrocelli

    Is it possible to set up a Control switch to react like a bypass switch between Scenes

    Thank you very much - i never used the „Manual“ Controllers. Sounds a little difficult for me but i will try your solution.
  59. Petrocelli

    Is it possible to set up a Control switch to react like a bypass switch between Scenes

    I have a problem with control switches. I switch my scenes with a MIDI controller. In my main preset I use two switches on the FM3 to turn Delay and PlexDly on and off. With the third one I mainly switch the boost and/or the Fat Switches in the amp block. Now I would like the boost to behave in...
  60. Petrocelli

    Signal Characteristics

    If you will use a highly recommended active Di, you have to use a XLR to TS Cable, and the Di has to be a Modell that can be external powered, because powering with 48V Phantom Power isn't possible in this configuration.
  61. Petrocelli

    AES - Axe FX output to RME UFX II not working

    Have you tried to set the Axe Fx to Clock Master = internal Clock! Switch RME to SyncSource extern. You need only one Cable from AxeFX AES out to RME AES in! Do you have another AES Source to test the RME?
  62. Petrocelli

    AES - Axe FX output to RME UFX II not working

    So you connected AES/EBU in both directions and tested the XLR cables? The RME runs now with Clock internal, so the AxeFX should get the Clock, and i think its there, because otherwise a "No Clock" Message is there. Maybe you can try to switch the AxeFx to internal Clock and try to Clock the RME...
  63. Petrocelli

    Axe-Fx III Firmware 23.00 Public Beta #1

    I just installed the beta and...it's unbelievable, even presets switch seamlessly - how does that work!!! I think that's really crazy and I never thought it would become a reality! And the JS410 Green Lead sounds really great too! I wouldn't have thought that the new HighCut in the Hall Pitch...
  64. Petrocelli

    FM3 Firmware Version 7.00

    Had also a freeze yesterday - newest firmware, PC with newest FM3 Edit was connected. Used my long time basic preset with about 70% CPU usage. (Not at home so cant post the preset) FM3 frozes during playing without switching anything on the FM3 - after that only dry Guitar sound come to my...
  65. Petrocelli

    GK 250RL Gain Channel

    Hi Leon, just tried your Preset - thank you very much. I find a small Bug in it: The EQ Knobs in the Performance Page are linked to the wrong ParaEq Level Knobs: 8K is 120Hz, 2K is 500Hz and so one! Very interesting to try this Amp!
  66. Petrocelli

    BlueAmps Cabinets

    I am also interested in the Cubo. Now i play with a Laney 1x12 FRFR, which is not so bad with some FM3 global EQ tweaking - but i like the Idea with stereo coming out of one Cab (i know that the stereo image can‘t be as wide as seperate Speakers). But i wish to know if the Cubo is as loud as my...
  67. Petrocelli

    Jon Scofield Effect Help

    The Sound in the Recording doesn’t sound for me like in the Rig rundown. I think the trick is to push the Chorus Mix to 100%, so the Chorus gets to a Vibrato (no Dry Signal) and a high Rate setting.
  68. Petrocelli

    What doesn't the Axe Fx do effect wise

    Mutronics Mutator, i know with two or more Filterblocks a Drive and Env Follower/LFOs you can come close but i like to have al this in a single Block so an enhanced Filter Block would be nice!
  69. Petrocelli

    set Song Tempo for each song – overview – and a brand new solution

    We use SongBook by Linkesoft since a few years in our Trio, i switch my FM3 Presets per changing the Song sheet in SongBook per Midi over Bluetooth. And now a long wish gets true - the new version can send the Songtempo Metronome per Midi, so my Delays run in sync also in my kitchen sink...
  70. Petrocelli

    Looking for setup advice (switching between RME and FM3)

    Mackie Big Knob passive Monitor Controler. You need also XLR to TRS Adapters!
  71. Petrocelli

    Bug? virtual capo

    Do you play loud enough that you really don’t hear your Guitars acoustic Tone! Maybe try with a closed Headphone. I had the same thing playing at bedroom levels with the virtual capo!
  72. Petrocelli

    Axe-Fx III Firmware 22.01 Release

    No Problem here - maybe only on specific Amp Modells?
  73. Petrocelli

    FM3 Firmware Version 7.00 beta 5

    uiuiui - cant wait to try it out at home!
  74. Petrocelli

    Using ADA MP1 with Axefx III

    I Don’t own an external PreAmp - i would run it in a Loop in the AxeFx, so you can use Drive and other Blocks before and Delay, Verb, etc. behind. So you can it also use with IRs and your Headphones on a second Path!
  75. Petrocelli

    FM3 Firmware Version 7.00 beta 4

    Windows Keyboard shortcut for Block initialise! Strg (German Keyboard) = Ctrl
  76. Petrocelli

    FM3 Firmware Version 7.00 beta 4

    This are the Preset and System settings!
  77. Petrocelli

    FM3 Firmware Version 7.00 beta 4

    I can reproduce this even without changing to Dyna Cabs - after hitting "Strg + I" FM3 hangs
  78. Petrocelli

    FM3 Firmware Version 7.00 beta 4

    Played with the "5153" Preset, Scene 4 (Blue 50W). Changed Cab Block to Dyna Cab with the 5153 Speakers (Dyn2+Ribbon). Changed Amp Block to PVH 6160 Block Crunch. All good, then pushed "Strg + I" to initialise the Amp Block - FM3 hangs and i had to power cycle!
  79. Petrocelli

    FM3 Scene Switching Lag

    There is a great post obout Gaps and reducing them in the Axe FXIII Forum: https://forum.fractalaudio.com/threads/get-rid-of-switching-audio-gaps-p1-6-technical-measurements-and-info.195653/
  80. Petrocelli

    Bug? (Almost) no dry signal at the drive block mix control

    Yes you are right, but i dont understand why the functionality isn't consistent in all Drive Blocks! In some Drives the Mix knob works as what a "Mix Knob" should do, in others not. As i tried the B7K Drive Block for my Bass Presets i recognized there is something wrong with the Mix Knob (as in...
  81. Petrocelli

    Bug? (Almost) no dry signal at the drive block mix control

    As i posted in another thread, I tried all the drive pedals and found out that all Fuzz Pedals, Bit Crusher, FET Pre, Mid Boost, SSD Pre, Shimmer Drive, Tape Dist, Treble Booster and 3+4 Knob Tube Driver B7K also have a problem with the "Mix" Parameter. Here the level pot still has an...
  82. Petrocelli

    Ten Tap Delay Bug

    Time 1 is not the Time between the first two hits on "Enter" but the Time between switching "Learn" on and the first Hit on Enter.
  83. Petrocelli

    Ten Tap Delay Bug

    Bug? The 'Learn' function in the Ten-Tap Delay - Rhytm Tap Delay doesn't work properly because the Tap10 Time is never reached when typing in the rhythm with the Enter key. Before that, the 9 other values are reset. In addition, the Tap 1 Time often does not correspond to the period of time...
  84. Petrocelli

    Wish Enhanced Frequency Bandwith for Low/High Cut in the individual Cab Sections

    yes i know, but my idea is a complete simple thing - it is all there in the cab block, only the frequeny range of the Low/High Cut Filter has to be changed to get an overlapping range! And cab sounds can be easyly stored as a block preset, which is not possible with a construct of a seperate...
  85. Petrocelli

    Wish Enhanced Frequency Bandwith for Low/High Cut in the individual Cab Sections

    I like to have a "x 10" Frequency Switch for the Low Cut and a "x 0,1" Switch for the High Cut in the Cab section / "Cab" Tab. With the expanded frequency range it will be possible to do "two Band Crossover Cabs". So if you like the Bass Response from one IR/Dyna Cab and the High Part from the...
  86. Petrocelli

    Sound Difference Using FM9 As Interface

    Fractal Gear is 48KHz Sample Rate. If you connect it digital to a seperate audio interface you have to use the same SR und clock it as a slave!
  87. Petrocelli

    FM3 Firmware Version 7.00 beta 3

    Tried the Bosom Boost - No Problem here! Maybe post a Preset with the Problem!
  88. Petrocelli

    FM3 Firmware Version 7.00 beta 3

    "Global Settings - Config - Input Gain" is this new? I wished so long for this to use different guitars without dialing in the gain in each Preset. Also love the Dyna Cabs and the Revv - thank you very much!
  89. Petrocelli

    looping variable pitches

    Very interesting, do you like to share your preset?
  90. Petrocelli

    Struggling with spillover and plex delay

    i am not at my III, but if you mute the „out“ in the plex delay block this block will always „hear“ what signal gets in, indifferent its muted or not. So if you unmute the block you hear this little part of audio. Try muting the „in“ side - so there will be spillover when you mute, but i think...
  91. Petrocelli

    Axe-Edit III 1.13.02

    @Michael Pickens Under Cab Block Type: "Dyna-Cab" - Cab More... is the "Proximity Frequency" parameter. I think this parameter is only for the Lagacy Type and has no function in the Dyna Cab Type. Shouldn't it be removed there? Also thank you so much for your work Tom
  92. Petrocelli

    AES/EBU Cable from Output 1

    The FM3 has only a S/PDIF Chinch Out, the XLR outs are only analog! There are S/PDIF to AES/EBU Converters, but I don`t think it makes sense in a Live Situation. Also, the FM3 has to run as Clock Master (there is no Clock input to run as a slave) - I believe no FOH engineer would accept to clock...
  93. Petrocelli

    Has anyone visited Thomann in Germany?

    Enjoy the local frankonian beer - they have a lot of little breweries there! 🍺
  94. Petrocelli

    Does Dynacab + SIC create something similar to DSR?

    This + the automatic time align if you use more mics is also a great functionality in the dyna cabs!
  95. Petrocelli

    Spdif out and global EQ

    For me, this is a perfect solution! In the rehersal room i plug to my FRFR with Global EQ to flatten the Speaker, in the Studio i go to my UAD Apollo per SPDIF with the pure, uneq‘ed Sound. So i never had to think about switching EQ on/off!
  96. Petrocelli

    Axe-Fx III Firmware 22.00 Public Beta #6 (Beta 12)

    Today i took my Five String Bass and just fall in love with the 2x10 Heart Key Cabinet and the Citrus Bass 200 Amp (Try also changing the Tonstack to the "Active" Type!) For me the fullest sounding Bass Cabinet in the AxeFX including all the Legacy Cabs. Also the Dyna-Cab 1x15 Portabass didn't...
  97. Petrocelli

    4CM high squeal

    have you also your PC/Mac connected? Disconnect the USB! Use the same socket for powering amp and fractal!
  98. Petrocelli

    FM3 and Cello? This is Pretty Cool

    You are right, i was confused because the Instrument looks so tall in the video near her standing and the headstock looks like a classical bass!
  99. Petrocelli

    FM3 and Cello? This is Pretty Cool

    …but this is a bass, look at the headstock and dimensions!
  100. Petrocelli

    How to record a string quartet with the axe3?

    I can only give you Tips for the Mic placement, but don’t understand exactly why you want use your AxeFX for that! Two Omni Condensor Mics (e.g. Schoeps MK2H, B&K 4006), about 40cm on a Traverse on a Stand before the ensemble. Stand hight dependent on the Reverb Circle of the Room and maybe a...
Back
Top Bottom