Search results for query: *

  1. Spawn2031

    Nektar Pacer....thoughts?

    Hey guys, thank for all the reviews on this piece, I snagged one as well as an upgrade for my FCB1010. I was able to get it programmed just fine for what I need all except for the ability to do banks like the FCB did. I have a set of 5 presets that I use almost exclusively and, when I was...
  2. Spawn2031

    Sudden loss of bottom end

    Yeah my bad... other way around. Still, the noise floor dropped by 1/2. So very odd with no smoking gun.
  3. Spawn2031

    Sudden loss of bottom end

    Ok so the problem is fixed, doing a factory reset on it did the job. The odd thing is, I went through all parameters I could think of and saw nothing out of place but everything was sounding better than ever afterwards. One other issue it fixed that I had just learned to live with was the...
  4. Spawn2031

    Sudden loss of bottom end

    Yeah I was kind of thinking it wouldn’t be a bad idea to wipe the whole thing clean and start from scratch. I got it used years ago and never had s problem till now. The guitar I was using is passive so it’s not a battery issue. I’ll post up my preset as soon as I get a chance.
  5. Spawn2031

    Sudden loss of bottom end

    Nope, I was hoping it would be so simple as that. No changes in the global EQ, all presets affected. What the hell is goin on here?
  6. Spawn2031

    Sudden loss of bottom end

    That’s a very good question... the patch was initially set for auto engage. I’ll have to chk to make sure it’s actually turning off. I did swap out the midi controller
  7. Spawn2031

    Sudden loss of bottom end

    Hey guys, got an odd issue here. Played my last gig about a month ago and everything sounded as expected. Finally hooked everything back up this past weekend and my normally thick and ballsy tone now sounds weak and kinda shrill. I have not changed any settings and it sounds this way both...
  8. Spawn2031

    Considering a new foot controller

    Interesting, I hadnt heard of this one. Yeah that would do the trick. I've got my eye on 2 expression pedals from Mission Engineering when I make the switch. USB or battery powered huh? Have you used this one? How long does it run on batteries? This is going to be for live performances so...
  9. Spawn2031

    Considering a new foot controller

    Hey guys, I've been using and FCB1010 for the past couple years with my Axe and, for the most part, it's been fine for me. I dont do a whole lot of switching back and forth. I only use 3-4 patches per show. My only real complaint with it, and hence the reason for thinking of getting something...
  10. Spawn2031

    Vastly different sound between monitors and FOH

    No I dont believe it ever has. It's your standard old school PA with 3 way tops, subs and separate amps for all of it. Definitely not anything remotely close to the kind of rigs we try to setup to function on FRFR cabs. Maybe I should just toss an SM57 infront of my cabs and say screw it! lol
  11. Spawn2031

    Vastly different sound between monitors and FOH

    Nope, nothing was different. XLRs to the same board I always use, inputs on the board wernt clipping. Nothing changed within the Axe or patch itself. Just the PA was the difference. So I'm assuming that I'm going to need to tweak my patches now so that they sound good for the PA without any...
  12. Spawn2031

    Vastly different sound between monitors and FOH

    Hey guys, My band finally left the basement 2 weeks ago and started playing out on a Carvin PA system. Until now, we've been playing thru my soundboard and out thru monitors in our practice area (Output 1 both XLR to the board and routed to monitors / Output 2 both 1/4in running direct into 2...
  13. Spawn2031

    Godsmack Bulletproof Intro effect

    This sounds like a pretty good idea and since it's all happening as the guitar is fading in, I could further add a volume block using the same controller to have it do all of what you pasted as the volume is swelling to full on.... right?
  14. Spawn2031

    Godsmack Bulletproof Intro effect

    Hey guys, I'm having some difficulty in recreating the effect on the guitar in the very beginning of this song. Anyone have ideas / pointers?
  15. Spawn2031

    Left channel XLR out suddenly not working

    Positive. When I took the right side and plugged it into the monitor direct it behaved as expected. Anything plugged into the left output was just dead. That is, until I fired it all back up at home. I changed nothing and everything worked as it should.
  16. Spawn2031

    Left channel XLR out suddenly not working

    In this circumstance I had the right XLR going to the board and the left XLR (the output in question) going to my monitor. I tried swapping cables and playing several times but eventually since everyone was waiting on me, I said screw it and just plugged my monitor into one of the aux sends on...
  17. Spawn2031

    Left channel XLR out suddenly not working

    When the problem was actually happening I tried another cable that I knew worked and it still had the issue so yeah, maybe a dirty jack. It looks clean though and 90% of the time it's always got a cable plugged in so I dont know how dirt could have gotten in there. I rarely remove them...
  18. Spawn2031

    Left channel XLR out suddenly not working

    Ok, so even more freaky now... I go home last night completely prepared to check out what I hadn't checked that was mentioned here, set my rig back up and everything is working perfect. I've had my axe for 3 years now without a single issue, anyone have any kind of clue of what could possibly...
  19. Spawn2031

    Left channel XLR out suddenly not working

    There is a volume block in the chain at the end but it is functioning properly. Everything is panned center. I have not tried resetting the Axe yet as I am reserving that until I've exhausted my other options.
  20. Spawn2031

    Left channel XLR out suddenly not working

    I know I haven't changed anything on it, where / what should I look at there? I haven't checked the 1/4in outs for output 1
  21. Spawn2031

    Left channel XLR out suddenly not working

    I tried using the cable coming out of the right XLR (which was working) and tried it in the left output and still got no sound out of it. I also took the cable that was originally coming out of the left XLR and ran it into the soundboard with a mic attached to it and got sound, so it appears...
  22. Spawn2031

    Left channel XLR out suddenly not working

    Yeah, the problem appears to persists across all presets so it's likely a global issue. The one thing I didnt get a chance to try yet was to create a blank patch and see if the problem persists, but I expect it will.
  23. Spawn2031

    Left channel XLR out suddenly not working

    Hey guys, I've got an issue that cropped up suddenly with just one of my XLR outs not working. It was working fine at home, take it to practice and all of a sudden nothing is coming out of the left channel XLR jack. I've tested the cables and they are fine. The way I have been running is...
  24. Spawn2031

    Quick double lead help

    Thanks a ton guys, actually just even seeing the harmonies laid out like that makes it so much easier to understand what I need to make the axe do. This is going to be for a live performance and unfortunately I dont have the ability to enlist a 2nd guitarist that could play it with me so...
  25. Spawn2031

    Quick double lead help

    Sorry to bother you guys with this as I'm sure it's not difficult at all but I am horribly bad at figuring out dual guitar harmonies. I've provided a link to the part I'm trying to figure out and the solo starts at 2:10 in. It sounds like a fixed interval so I'm using the adv. Whammy but can't...
  26. Spawn2031

    Axe-Fx II "Quantum" Rev 10.01 Firmware Release

    WOOOT!!!! Hellz yeah!!! I honestly didn't expect this at all! Thanks Cliff!!! So would I be wrong to assume we can expect new preset banks soon?
  27. Spawn2031

    Unexplained pop when switching

    Thank you very much sir, I will try this out when I get home tonight!
  28. Spawn2031

    Unexplained pop when switching

    Hey guys, I have a issue that I can't track down. I have 2 presets that I want to combine into one. When switching between these presets as stand alone patches there is no issues. However, when I combined them into a single preset and use scenes to switch between them, I get a pop when...
  29. Spawn2031

    My laptop blows

    I am using the XLR outs. I thought lifting the ground could be dangerous forvthe Axe though...
  30. Spawn2031

    My laptop blows

    I will try wrapping it in foil as a test. I can't move the transformer very far because the cord from the transformer to the laptop isn't very long and the plug going in is a multi pin that I've never seen before on any other laptop or power cord, so not much of a way to get the transformer...
  31. Spawn2031

    My laptop blows

    It's much worse when I have my guitar next to it, yeah. My wireless unit seems to either make it worse or it's picking it up and amplifying it but the sound is there even when my guitar is unplugged from my rig.
  32. Spawn2031

    My laptop blows

    So I almost always run my laptop connected to my Axe which then always runs direct into our board. Whenever it's all running I get some lovely unwanted digital sounding BS in the line when everything is supposed to be silent. Unplug my laptop's power supply and it goes away. I have my laptop...
  33. Spawn2031

    Axe clipping speakers but no red lights on Axe

    I'm one of those who tries to do it by the book as much as possible. My mixer recommends that all inputs come in reading about 50% of the meter. Right now, my axe signal is reading at about 35%. This is with my mixer input trims at unity. If I turn up my mixer trims to make the input meet...
  34. Spawn2031

    Axe clipping speakers but no red lights on Axe

    Did that and everything sounds great, thanks so much Cliff! Much better than it ever did. I'm glad I posted on here about this considering I had always been under the misconception that those outputs were best left at max.... now I know. So here's one final question... With turning the...
  35. Spawn2031

    Axe clipping speakers but no red lights on Axe

    Here's the preset in question
  36. Spawn2031

    Axe clipping speakers but no red lights on Axe

    Input trims on the mixer, not the axe.
  37. Spawn2031

    Axe clipping speakers but no red lights on Axe

    I most certainly will. I did just get the clipping to stop by turning the outputs down to to about 10 o'clock. But I had to crank the input trim up to 75% which is a little less headroom than I prefer. I'd love to have someone take a look at the gain staging. I'll upload shortly.
  38. Spawn2031

    Axe clipping speakers but no red lights on Axe

    Ok, I'll try turning them down even further. I'll be happy as he'll if it's that easy of a solution
  39. Spawn2031

    Axe clipping speakers but no red lights on Axe

    Just turned them down to half instead with no change, so thats not it
  40. Spawn2031

    Axe clipping speakers but no red lights on Axe

    Yeah, I running directly into the line lol inputs on the board, not the mic pre. I always read it's best to have those maxed. Long time ago, when I first got it.
  41. Spawn2031

    Axe clipping speakers but no red lights on Axe

    Forgot to mention, output dials are set to max as I've read is best to do.
  42. Spawn2031

    Axe clipping speakers but no red lights on Axe

    So pretty much what the title says here. My axe runs direct into our board and I need to run pretty loud since my drummer is a beast. I have my global inputs set so I just barely ever see red and almost never see red on the front when I'm playing my preset. When I watch the horizontal vu...
  43. Spawn2031

    FCB1010 Optical expression pedals

    I didn't know about the cleaning part but oh hell ya you are so right about the spacing of the expression pedals. More than a couple of times I have accidentally hit my volume pedal while using my wah and fucked everything up, lol. I'm sure eventually there will be an upgrade in my future, but...
  44. Spawn2031

    FCB1010 Optical expression pedals

    Nope, not condescending at all. I'd imagine that's a pretty easy mistake for someone to make. I am doing my calibrations on the FCB itself so no issues there, though I have not tried doing it with the quarters like you suggest. I'll have to give that a go after I pay attention to that sweep...
  45. Spawn2031

    FCB1010 Optical expression pedals

    I have messed around with it but I always seem to make it worse. Given that you would think the volume to position ratio should be 1:1 you would think, I keep defaulting back to the standard straight line from bottom left to top right. But that just doesn't give a natural swell. Once I took...
  46. Spawn2031

    FCB1010 Optical expression pedals

    Hey guys, so for as long as I've had my axe I've been using my FCB and it's always done great for me except for it's damned pedals. They work great for Wahs or for adjusting gain back and forth but I never seem to be able to get a nice smooth volume swell out of it. Considering that the curve...
  47. Spawn2031

    Counteracting Fletcher-Munsen live

    I'll see if I can post up an example of it although, I did a small experiment last night at practice and used my Alto 10" floor monitor at the same volume as my 12" Peavy Dark Matters (which is what we are using for mains right now) The Alto still had that nice squishy / spongebobish sound...
  48. Spawn2031

    Counteracting Fletcher-Munsen live

    Cool, thanks for that. That will definitely be helpful as I've got to create 4 different versions of yhis thing for live and most likely that midrange will be different with all 4. And yes, I know that FM doesn't actually change anything it's simply an effect of perception at different...
  49. Spawn2031

    Counteracting Fletcher-Munsen live

    Thanks for chiming in Yek! So you just knock those 2 frequency ranges down? I thought typically you needed a mid range boost as well. When I first cranked this patch up it sounded very scooped. Any idea on where to look to solve issue #2?
  50. Spawn2031

    Counteracting Fletcher-Munsen live

    So then your doing with an EQ block after the cab?
  51. Spawn2031

    Counteracting Fletcher-Munsen live

    Hey guys, I have an absolutely killer tone matched patch that I love using for just about everything and plan on using it live. I am completely aware of how the Fletcher Munsen curve augments highs/lows and drops out mids at high volumes but I never seem to really be able to counteract it very...
  52. Spawn2031

    Muddle o' Pudd verse

    Hey guys, looking for some pointers on what effect combination these guys are using during the verses for the song Control
  53. Spawn2031

    Quick Emergency Schematic Check Please

    Ok, so the reason I had to do all of this on the fly was because of a last minute notice audition for me doing guitar and vocals with a band. Seems I'm going to get the job.. whoo hoo!! So now I need to set this up the right way. So, I could either A) drop about $2-400 on a small vocal fx...
  54. Spawn2031

    Quick Emergency Schematic Check Please

    So got it all setup and it all worked as expected except I couldn't kill the dry signal and run it 100% wet. For some reason the way this mixer works, the fader also controls how much signal is sent to the axe also. Kill the dry signal going to the mains and it kills everything. It's not the...
  55. Spawn2031

    Quick Emergency Schematic Check Please

    Actually, for the time being it will only be one vocal track right now, so that might just be the way to go then. Kill the dry signal fader and only let the wet signal from the Axe go thru.... genius. Thanks a ton man!!
  56. Spawn2031

    Quick Emergency Schematic Check Please

    Gotcha, so the only way to properly gate this would be if I had a separate mic preamp and ran it directly into the 2nd input of the Axe. So the compressor would be useless as well because it would only be compressing the FX, not the dry signal
  57. Spawn2031

    Quick Emergency Schematic Check Please

    Oh, just remembered, I should add a noise gate and compressor in there too. Would it really matter where it should go as long as it's before the effects blocks?.. Whew, this is starting to get a little big now...
  58. Spawn2031

    Quick Emergency Schematic Check Please

    As it sits right now just basic chorus / reverb / delay. Nothing crazy that pans or bounces. If this works out well tonight then I might add some stuff like that in but I gotta balance it with the guitar so I dont overload the DSP too much. The guitar chain has a drop tune affect that certain...
  59. Spawn2031

    Quick Emergency Schematic Check Please

    According to the manual for the mixer, if I just put it in the L input it copies the signal to the R, but hey... I certainly dont mind running both cables just in case!
  60. Spawn2031

    Quick Emergency Schematic Check Please

    Ok got it, set the blocks at 100% wet (I think it actually suggests that in the manual) and go ahead and run both L/R outputs into the L/R ST Returns
  61. Spawn2031

    Quick Emergency Schematic Check Please

    Ok yeah that makes sense. No shunts to the input/output. What do u mean by the mixer's send/return setup in parallel? It has a single mono fx out and stereo fx in to the left of it. They "appear" to be in 2 separate blocks but I dont really know how the internal wiring goes.
  62. Spawn2031

    Quick Emergency Schematic Check Please

    Hey guys, before y'all go any further, just know I am aware this isn't the ideal way to set this up :) but it's all I've got to work with at the moment with very short notice. I'm being asked to get vocals running thru my Axe for a party tonight and I've never used the FXL loop before. I have...
  63. Spawn2031

    Importing Presets

    Hey guys, quick question here about importing presets into the latest FW. If a preset was made prior to Q7.02 and gets imported, should the amp still be reset and re-dialed back in in order to take full advantage of the FW? If so, is there an easy way to do this as the presets I'm talking...
  64. Spawn2031

    Axe FX for Guitar and Vocals - Should you do it?

    Awesome glad to hear it!! Yeah I'm not a huge fan of overly affected vocals so it wouldn't be much more than what you listed there. Currently I have my axe running directly into my boards' line inputs. Pardon my newbiness on running a mic into the axe fx but what mic preamp would you...
  65. Spawn2031

    Axe FX for Guitar and Vocals - Should you do it?

    Hey guys, I know this has been discussed many times about how to set something like this up so I know it's doable but should it be done? Does setting up a good patch with a nice lush vocal setup and a good guitar setup need more resources than an MKII has available? For those of you that have...
  66. Spawn2031

    New To Axe FX Modeling

    Absolutely do this first!! It was a step I missed for awhile and I struggled until I came across it. I have used a PRS Custom 24 into the Axe as well and, depending on the sounds you like, a good starting point would be Mark Day's HBE (Fremen had a free version of it that was even better IMO)...
  67. Spawn2031

    Legacy Firmware Solution

    It most certainly does! When I was still an L6 guy thinking of upgrading and doing all of my research, damn near every board I came across talking about comparisons between companies and various models, this unending dedication to your product and your customers was CONSTANTLY mentioned. No...
  68. Spawn2031

    Axe-Fx II "Quantum" Rev 6.00 Firmware Released

    Cliff, as a fellow bearer of the carpal tunnel plague, I feel for ya and appreciate all the work that you do man. I think we all knew you'd come up with something but I don't think we expected it'd be something like this. I can't wait to get home and check this puppy out!
  69. Spawn2031

    Legacy Firmware Solution

    Absolutely agreed!!! Thank you so much for all your kick ass work!
  70. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    Yes absolutely that is a damn good run. Especially in an industry where this kind of constant development is unheard of and if this is where it stops due to technical reasons or because they just plain don't want to keep updating it, that is Fractal's prerogative. But what you guys in the...
  71. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    Jason, I agree with you on the part of I would like my presets to stay the same or get better when upgrading FW. But that's why, in older days, you keep a copy of your current FW and roll back to it if you don't like the newest. It's your personal choice. No one is forcing you to stick with...
  72. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    wow, that's some serious sniffin around to find that! lol.
  73. Spawn2031

    Remove Legacy Version Option from Firmware - Mark l/Mark ll

    I can understand it. I personally don't have a whole lot of time between my job and kids. I have my Axe sounding just how I want it right now and, IF an update screwed all that up for me, I wouldn't really have the time to go through it all again and have it ready for band practice, even if I...
  74. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    1) I can't presume to know Cliff's mind but.... Because the XL with it's extra space existed way before the option to select FW was created. That was created as a direct result of people constantly saying their sounds changed after the latest update. Correct me if I'm wrong but that really...
  75. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    Cliff absolutely deserves every bit of our praise & respect no doubt there and if the guy says nope, this is it, we would be assholes as customers to demand it to be otherwise. The guy is a genius and if there's a way to try and make everyone happy, I am sure he will do it... he always seems to...
  76. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    Not to mention the XL's greater storage capacity was not intended to store old fw. Plus, would anyone buying one of them today actually take the time to check out their patches in all the past fw versions? I kind of doubt it. I'm pretty confident that anyone buying it today might not even...
  77. Spawn2031

    Remove Legacy Version Option from Firmware - Mark l/Mark ll

    Completely agree here, if you don't want to lose how your rig sounds using the OLDER fw, why would you upgrade anyway? Sure, I know the answer to that would be b/c the upgrade MIGHT be better. The poll that I am running right now it showing that these ppl are vastly in the minority and...
  78. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    Guess I missed that. I was wondering where that 4% number kept coming from. Well here's their chance to speak up one last time as it will greatly affect all of us going forward.
  79. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    I completely agree with you on this. It does appear that the majority of us would prefer to move on. However, to be fair, that's why I started this poll. Are those that want the legacy fw so few? I personally would think so but we will see!
  80. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    Go for it, change whatever you see fit! *edit* nvm, I saw where to change it.. doh, lol
  81. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    No, I'm pretty sure you're right on that. I edited it a bit so that is pointed out now.
  82. Spawn2031

    MK I/II/XL Legacy Firmware Poll... to remove or not to remove

    ***For those of you that aren't caught up on the issue, Q6 is coming and the MK I/II is being left out due to space restrictions. These restrictions wouldn't be an issue if the legacy fw was removed. Good, we all get to move on and keep updating... Bad, MK I/II/XL lose the ability to update...
  83. Spawn2031

    Axe-Fx II "Quantum" Rev 6.00 Public Beta

  84. Spawn2031

    Axe-Fx II "Quantum" Rev 6.00 Public Beta

    Personally if my MKII never received another update, I wouldn't be pissed. I love the way it is right now but I just gotta say... these vocal opponents, what are they gonna oppose more? Deleting old F/W versions or the end of the updating line. I guess that's a debate that could probably go...
  85. Spawn2031

    how to reduce latency on down shifted patches

    I'll have to mess with that then. I'm not sure what the CPU usage is at off the top of my head. I do know that this is essentially the exact same preset I've been using since I tried it last. When I tried it last I know it was set to LOCAL and it sounded like I was playing through a Morpheus...
  86. Spawn2031

    Delay (audio gap) when switching scenes

    Yup, that got me before too.
  87. Spawn2031

    how to reduce latency on down shifted patches

    Kind of funny that this thread got posted as I was just about to create one about the same thing from my weekend's work with setting up down tuned patches. The first time, I set this stuff up ( a few months back) the latency killed me, couldn't handle it, even when only dropping 1 semi tone. I...
  88. Spawn2031

    Quick compressor question

    Hey guys, I need to setup a compressor for my clean tones for one particular guitar. Seems my PRS is incredibly sensitive to picking dynamics.. which is really cool, just more so than my other guitars. So I need a compressor just to normalize those dynamics for now. Which compressor type is...
  89. Spawn2031

    Changing a modifier curve - Volume control

    Hmm, I'll have to give that a shot and see what happens. I appreciate the tip. I'll let ya know if it helps mine too.
  90. Spawn2031

    Changing a modifier curve - Volume control

    Yeah, I probably would have passed on this thing if I had realized the expression pedals were optical. Oh well it is what it is until I can afford a better solution. I can live with it as long as I can get this volume pedal a little smoother.
  91. Spawn2031

    Another trick...High Pass / Low Pass

    This is probably one of the biggest things that people forget about amp modelers. They are meant to reproduce the sound of a mic'd amp, not just the amp itself. So in order to do a true comparison you would have to mic up the real amp in the room as well, which is naturally going to change the...
  92. Spawn2031

    Changing a modifier curve - Volume control

    The FCB has a calibration that you run on itself to set up your expression pedals. Figured that would be enough. Hopefully this will be the fix I am looking for. It'd be nice that it was just a missed step.
  93. Spawn2031

    Changing a modifier curve - Volume control

    You know... I may not have done that. So many thing to learn and remember when I first got my axe, I honestly can't remember if I did that or not. Certainly wouldn't hurt to try. Isn't that only for pedals plugged into the pedal jacks in the back? This is midi footboard
  94. Spawn2031

    Changing a modifier curve - Volume control

    I get the actual mechanics of how to change the curve. I'm talking about how to I go about counteracting that super quick drop when I first pull back on the pedal? Do I just grab those points along the curve and just move them about until I got something that I like or is there a more precise...
  95. Spawn2031

    Changing a modifier curve - Volume control

    Hey guys, got an FCB1010 that I'm using to control wah and volume. I'm having a bit of an issue with the smoothness of the expression pedals on this. When I just barely pull the expression pedal back to decrease the volume, the volume drops dramatically at first and then smoothly from there...
  96. Spawn2031

    Big wave of buyer's remorse.....help calm me down.

    As many others have said in here, my Axe is my ultimate favorite piece of equipment. I too had a little bit of buyers remorse when I got mine because I was on the wait list for the Ax8 when I saw an opportunity to get a used MKII. I was concerned with questions like yours, worried that I...
  97. Spawn2031

    Axe FX II - noise when using hi-gain presets

    I had this problem with a new guitar that I got awhile back. Horrible sound like this, got worse as I approached the PC but never entirely went away no mater how far away I got. I concluded that it was a shit ton of interference from multiple different sources in the basement (fluorescents /...
  98. Spawn2031

    As it sounds soo good-humble question-what is a Metallica MKIIC++

    Yeah, I think the mid slider on my setup for this is almost all the way down. Super scooped. I wonder how this would sound with a pair of those new metal pups PRS put out.... hmmmm
  99. Spawn2031

    Axe-Fx II "Quantum" Rev 3.03 Firmware Release

    The Metallica sound you get from this with Mikko's settings are kick ass for sure, but I gotta second your thought too! I tossed the orange 4x12 stock cab on it and it blew my mind. Effin' awesome! Thanks 1000x over for this update Cliff! If nothing else, I get to act like I'm 17 again...
  100. Spawn2031

    As it sounds soo good-humble question-what is a Metallica MKIIC++

    Sweet, I'm gonna give that a shot. It's a good thing my band's taking a break from learning new stuff right now cuz I'm pretty certain I'm going to be dusting off a lot of the old school Metallica this weekend. Simply bad ass amp.
Back
Top Bottom