Search results for query: *

  1. GlennO

    Setting Up Reamping With Interface and AxeFX USB

    See configuration #5: Although a 2i2 isn’t a great interface for this purpose. https://forum.fractalaudio.com/threads/axe-fx-for-the-recording-musician.177592/ But if you have to run a cable to the AxeFX anyway, why not make it the cable from your guitar instead of a cable from the 2i2? P.S...
  2. GlennO

    Wish Nonlinearity and Mixer Function for Cab Block

    I would humbly disagree. A vector mixer is more efficient and more intuitive. Yes, there are some blends you can’t achieve when using 3 or 4 IR’s, but those tend to be contrived cases. That’s why a single vector mixer control is popular in UI design for a blend function instead of multiple...
  3. GlennO

    Not a Bug Bug? - Sound glitch with FW 7.0 and SPDIF if not sync'd with audio card

    If you use the FM9 as the clock master (FM9 word clock set to "internal" and Focusrite Control Sync set to "S/PDIF") you'll only need one cable, going from the FM9 out to the Scarlett in. However, if you're interested in re-amping, you might want to use use two cables anyway. You'll find...
  4. GlennO

    Convolution reverb

    Altiverb was the first prominent convolution reverb, around 2005. That was followed by a wave of many other similar reverbs and every major DAW included a convolution reverb shortly thereafter. They are still widely used, but the popularity has dwindled as people have come to prefer the controls...
  5. GlennO

    [not possible] Okay, I'll say it... a second Amp block!

    Well, yeah, that's one way to look at it :). There's no free lunch. Dual amps on the FM3 could be done, given a sufficient willingness to sacrifice quality. There are always sacrifices that must be made when designing devices and, as your measurements show, the FAS devices in different...
  6. GlennO

    Convolution reverb

    There are some applications for which convolution reverb is superior to algorithmic reverb, so there's a place for convolution. However, the popularity of convolution reverb has waned in the past 10 years or so as developers like Eventide and Strymon have popularized creative uses of reverb...
  7. GlennO

    [not possible] Okay, I'll say it... a second Amp block!

    I'm unaware of any Axe-FX III comparisons that suffered because somebody turned down the quality setting, so it doesn't seem like offering that setting has caused FAS any harm. Making that feature available on the FM3 might permit a 2nd amp block, I'm not sure. I'm just saying there's a...
  8. GlennO

    Not a Bug Bug? - Sound glitch with FW 7.0 and SPDIF if not sync'd with audio card

    If you're asking if it's ok to not sync the devices properly, the answer is "no". Otherwise, you'll get random results, which might mislead you into thinking the problem correlates with firmware version, when it does not.
  9. GlennO

    Convolution reverb

    Convolution reverb would be nice, but, like so many things that would be nice features on the AxeFX/FM*, the limitation is memory on the device: Convolution reverbs would need more memory than is currently available.
  10. GlennO

    Not a Bug Bug? - Sound glitch with FW 7.0 and SPDIF if not sync'd with audio card

    If you don't set the FM9 to sync externally when the Scarlett is set to internal, you'll get seemingly random artifacts like you're describing. And of course you'll need to make two spdif connections, i.e. both ways, if you want to do that.
  11. GlennO

    FM9 Proper Setup for Plugins

    The 18 dB compensation is only an issue for the special case Nimbas asked about. If you follow the instructions in this re-amping tutorial, you shouldn't have any trouble: https://forum.fractalaudio.com/threads/axe-fx-re-amping-tutorial.190686/
  12. GlennO

    FM9 Proper Setup for Plugins

    For reasons that are not entirely clear (to me at least) the Out1 and Out2 blocks add 18 dB of gain. So if you simply connect an input block to an output 1 block, you'll add 18 dB of gain to the digital signal.
  13. GlennO

    Wish Copy scene opens copied scene

    This is probably a good idea. There are enough apps that work that way that I subconsciously expect it to switch to the scene I'm copying to, and like Moke I often end up editing the wrong scene as a consequence. The inconsistent way copy/paste is handled for scenes/channels/presets/blocks...
  14. GlennO

    How do I use outboard in fx loop with the digital connectors?

    Regardless of whether you're using an fx loop or not, it's important to adjust preset output levels to ensure a peak somewhere around 0 dB VU. You can use the output 2 block meter on the Axe-FX to help when adjusting that, or use the preset leveling tool in Axe-Edit. Once you do that, you'll...
  15. GlennO

    FM9 Proper Setup for Plugins

    The mute setting for the output mode does not affect pass through audio coming from the computer. If muting the output by setting the FM9 output mode to mute affects audio coming from the computer, you must be sending the computer audio through the grid. Don't do that :).
  16. GlennO

    FM9 Proper Setup for Plugins

    It sounds like you just need to turn on input monitoring. Depending on how you want it to work, you can turn on Logic's "Input Monitoring Only for the focused track". in Settings -> Audio -> General, then turn on input monitoring for that track. Although your steps 1 and 2 don't make sense, you...
  17. GlennO

    How do I use outboard in fx loop with the digital connectors?

    That looks fine. You can check the meters page of the main screen if you want to confirm you're getting the expected i/o. Are you saying you have a feedback problem?
  18. GlennO

    Can We Stop Calling It A Home Studio?

    Hans Zimmer's studio is probably one of the most elaborate studios in the world, but it would be considered a "home studio" by the traditional definition. The idea that a home studio can't be a pro studio, or that a pro studio can't be a home studio has become a anachronism. The two are no...
  19. GlennO

    How do I use outboard in fx loop with the digital connectors?

    Just set the source for the appropriate input block to digital, set the digital input source to spdif, and set the spdif out source to the appropriate output block. Post your preset if you need help eliminating feedback problems.
  20. GlennO

    CAMBIO DE ESCENAS

    Tienes que usar dos channels en tus dos escenas.
  21. GlennO

    Can We Stop Calling It A Home Studio?

    These days, that adjective serves only to indicate whether a studio has sleeping accommodations, but it doesn't really tell you much about the recording facilities.
  22. GlennO

    Tuning up the same as tuning down?

    To answer your question, re-pitching upward does indeed give better results than down. You'll get fewer artifacts in the sustain portion of the note. However, transients aren't any better up than down, so on the whole, the difference is often minimal.
  23. GlennO

    [SOLVED] Clearer DI waveforms while recording

    If you're using your FM3 as your audio interface when recording the DI, you got bad advice :). You'll find a re-amping tutorial here: https://forum.fractalaudio.com/threads/axe-fx-re-amping-tutorial.190686/
  24. GlennO

    Output settings copy

    I just checked and, yes, connecting the blocks in series does work. Are you sure you connected your Out2 block to your Out1 block?
  25. GlennO

    [SOLVED] Clearer DI waveforms while recording

    Assuming you're not turning down the levels when recording, that should be ok. You can confirm that by doing a reamp and see if the tone has the same gain as when you play your guitar through the preset. If it sounds the same, then your levels are correct. As I mentioned, if you just want to...
  26. GlennO

    [SOLVED] Clearer DI waveforms while recording

    That's correct. It should be a low level like that, just like your guitar, which may have lower output than some other guitars. You can zoom the waveform in Logic if you want to see it better.
  27. GlennO

    Output settings copy

    True, but what you can do is connect your Out2 block to your Out1 block in series. That way the scene levels in the Out1 block will automatically affect the levels in the Out2 block.
  28. GlennO

    VST synths -NI/Omni/Arturia

    Thanks for the kind words about Omnisphere. We set out to prove that a music creation tool can be both deep and have an efficient user interface, and I think we succeeded in making something that is indeed powerfully simple.
  29. GlennO

    Recording Guitar + DI + SM57 in DAW

    I don't understand what you're saying isn't working for you. The problem is you need to turn up the send block level (or put the send in a parallel path). That will allow you to record your mic. I'm assuming your guitar is mono, so just pan that left and the mic right, and record the mic and...
  30. GlennO

    Recording Guitar + DI + SM57 in DAW

    You have the output level turned down to zero in your send block. That will prevent the mic audio from reaching the usb output.
  31. GlennO

    After the Fractal update, latency has occurred

    You can reduce it by turning down the buffer size, but there will always be some latency in usb audio. However, assuming you're monitoring direct, the usb i/o latency of your Axe-FX is irrelevant when recording guitar.
  32. GlennO

    FM9 Proper Setup for Plugins

    Sure, just create a preset that consists only of an input 1 block connected to an output 2 block (remembering to turn the level of that output block down by 20 dB). Use usb channels 3/4 as input to your track that contains the plugin. That way, assuming you're monitoring output 1, you won't need...
  33. GlennO

    FM9 Proper Setup for Plugins

    USB channels 5/6 bypass the grid and are a copy of the AxeFX input. So it doesn't matter what you have in the grid. You'll just need to mute the output of the AxeFX so you only hear the monitored signal through the plugin. For example, change the Output 1 mode to "Mute" in your I/O settings...
  34. GlennO

    Bug? Arrow selection ↑ ↓ presets when Auto-Audition is ON

    I'm pretty sure that's a bug. It's supposed to step through the presets with the arrow keys when Auto-Audition is on, just like it does with IR's. It was working until fairly recently. You'll probably have to flag it as a bug to get attention.
  35. GlennO

    help with computer audio into Logic

    Here's one way to do it. Record usb channels 3/4 in Logic. Note however, you'll probably have to turn the level parameter of the In USB block down to about -20 dB.
  36. GlennO

    Axe-Fx III Firmware 25.00 Public Beta #2 (Cygnus X-3 Release Candidate)

    All this machinery making modern music can still be open hearted.
  37. GlennO

    What am I doing wrong? Audio from iPad

    If he could direct the output to a channel other than 1, then he wouldn't have a problem in the first place :).
  38. GlennO

    What am I doing wrong? Audio from iPad

    Do you mean those are the choices for the usb channel for the click audio? Check the meters page on the FM9 main screen to see if the usb channel is indeed changing when you change that. If it remains on 1 when you change it, that sounds like a Bandhelper bug.
  39. GlennO

    Axe-FX For The Recording Musician

    I agree with Moondog Willy. As I mentioned above:
  40. GlennO

    Axe-FX For The Recording Musician

    On the Axe-FX main screen, go to the meters page and verify that you have output on channel 3. But....I would advise against trying to use configuration #4 on Windows. You'll probably get better results if you send the mono guitar and mono bass over spdif left and right channels to the UMC, and...
  41. GlennO

    Axe-FX For The Recording Musician

    That looks completely different than what Moondog Willy is doing :). It looks like you're trying to use configuration #4 on Windows by aggregating with asio4all? If so, #4 usually doesn't work very well on Windows. But if you're determined to try to get that to work, the Cubase I/O settings you...
  42. GlennO

    Tone Matching and Fabfilter Pro Q3

    8000 bands? No :). ProQ3 has a maximum of 24 bands. My point is an IR is a more accurate way to export a tone match than a table of parametric EQ bands.
  43. GlennO

    How to set a CC# to a Source?

    Setup -> MIDI/Remote -> External. Select an unused External Control and press "Learn". Send a CC event from DP. Now you can use that External Control as the source in a modifier you attach to any parameter. After you do that, you can send CC events with that CC# from DP to control the parameter.
  44. GlennO

    Auto Audition cabs not working

    I rarely use anything but scratchpad #1, but I just tried #2 and it works ok for me. Are you sure you have #2 selected in the cab block?
  45. GlennO

    AxeFXIII MIDI Input receives TONS of messages

    That parameter value response traffic is normal, for example when running Axe-Edit. It has nothing to do with an expression pedal.
  46. GlennO

    Axe-Fx III Firmware 25.00 Public Beta #2 (Cygnus X-3 Release Candidate)

    FWIW, in past firmware updates which automatically changed parameters, the light would come on. I recall some confusion about that, with people wondering why that light is on even though they haven't touched any parameters. However, IMHO the light should come on, on the principle that you...
  47. GlennO

    Wish Wish please - Mimic (Mimiq) Block

    I don't known if I'd call a Mimiq "better", but it's different than the effect in the preset. Strabes is right, the effect in the preset is a chorus. The Mimiq uses multiple delays with shifting times and varying attack dynamics. The trick in the Mimiq is the delay shifts only occur upon note...
  48. GlennO

    Wish Wish please - Mimic (Mimiq) Block

    I don't know where people got the idea the stereo effect in the Petrucci preset is a Mimiq effect. It's a pleasing chorus, but it's nothing like a Mimiq.
  49. GlennO

    Bug? SPDIF latency compared to cable

    Keep in mind that, in a properly configured rig, i/o latency is compensated for in your DAW. That means that, assuming you're monitoring direct, the i/o latency is largely irrelevant. As you know though, the FM3 has a latency reporting bug that requires a workaround. There are many benefits to...
  50. GlennO

    Bug? SPDIF latency compared to cable

    SPDIF itself does not have any latency. But the device the SPDIF signal goes to will have some latency in its connection to your computer. That latency can be affected by various factors, most significantly by the i/o buffer size.
  51. GlennO

    Record video playing over backing track

    Final Cut does a good job of automatically syncing using Clip -> Synchronize Clips. You can experiment to see which audio source for the Quicktime recording works best for the synchronization. The mic picking up the room audio might work well, or the Axe-FX might work better.
  52. GlennO

    Record video playing over backing track

    Pass through audio isn't sent to usb output. It only goes to analog outs. You'll need to route the computer audio through the grid to an output block if you want it recorded. For example, use an In USB block and send computer audio to usb channels 7/8 using audio midi setup. Also, if you listen...
  53. GlennO

    Which SPDIF to ADAT/TOSLINK converter are you using?

    I’d be happy to answer your questions, but since that’s off-topic here, I’d suggest starting a new thread with any questions you may have.
  54. GlennO

    Which SPDIF to ADAT/TOSLINK converter are you using?

    FAS products have no i/o sample rate conversion. That would be nice though, and it has been requested as a wish for future enhancement. In the meantime, you must use 48KHz. In practice this rarely causes problems (see the section in the recording guide about sample rates). The conversion from...
  55. GlennO

    Which SPDIF to ADAT/TOSLINK converter are you using?

    All FAS products require 48KHz, so that's the only sample rate one would use for spdif i/o. There are many advantages to digital i/o over analog. Better fidelity, lower latency, easier to manage levels, no need to worry about clipping, etc. A spdif -> toslink converter won't have jitter since...
  56. GlennO

    Tone Matching and Fabfilter Pro Q3

    That gives good results, but you'll generally get better results from the Axe-FX TM because of the better resolution compared to ProQ3. You can get even better results from an IR you shoot then import into the Axe-FX IR player. Do your tone match with whatever (There are many plugins that can...
  57. GlennO

    Leon Todd revolutionizing what it means to make bank as a musician

    Pentatonic Miner
  58. GlennO

    Setting Initial Value of Volume Modifier

    You can't simply connect to a midi input and expect that will be merged into the output. The midi device needs to be capable of merging. As I mentioned above, if it doesn't have that capability, then you'll need to use a merger.
  59. GlennO

    Setting Initial Value of Volume Modifier

    You can loop back if your midi controller is capable of doing a merge of the scene midi block CC with its own output. Connect the Axe-FX midi out to the controller midi in. Or use a midi merger. Turn on "ignore redundant pc" and/or turn off "send midi pc". Or if your controller is capable of...
  60. GlennO

    A/B switch

    Normally this would be done inside the Axe-FX, for example with scenes where the output of one scene is louder than another. Is the problem that you don't have a footswitch to control your Axe-FX?
  61. GlennO

    help with computer audio into Logic

    You can loop the audio from the FM9 back into Logic using an In USB block routed to Out1 or Out2. Change your system output audio device to the FM9 and use "Configure Speakers" in Audio MIDI Setup to set the usb channels to 7/8.
  62. GlennO

    Routing USB Audio for live tracks from Mac

    By default usb channels 1/2 go to out 1. Do you want it to go somewhere else? The user manual has instructions for routing it to other outputs.
  63. GlennO

    Best way for adding an octave

    It's a bot. You see them on the forum from time to time. Eventually that account will be used to contact a forum member in the For Sale forum. They hope their (manufactured) history on the forum will help them gain the forum member's trust before scamming them.
  64. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    The whole purpose of the firmware update is to make your presets sound different, specifically to be a more accurate model of a tube amp. If that accuracy improvement is the reason you are updating the firmware, there are two steps to achieve that accuracy improvement: 1) Install the firmware 2)...
  65. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    Sure, you can both programmatically control the dynacab and programmatically compare the result to the target IR to achieve a "close as possible" match. But it would be a huge job for very little benefit. Let us know how it goes :).
  66. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    No, this is a pretty rare circumstance. I did a quick check, and it looks like it's been several years since there was an update that changes amp block advanced parameter defaults like this.
  67. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    There's no such thing as starting from scratch on the AxeFX :). It's confusing, but in practice, I doubt any of this will be much of a problem for anybody.
  68. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    Not exactly, no. The problem is there is no way to create presets on the Axe-FX (except a special sequence when you boot your Axe-FX). You always start from an existing preset. However, as long as you make a selection from the amp type menu in the course of creating your new preset, you should...
  69. GlennO

    Audio without DAW

    Sure, just connect your studio monitors to your AxeFX or connect your AxeFX to your Scarlett. You’ll find complete instructions here: https://forum.fractalaudio.com/threads/axe-fx-for-the-recording-musician.177592/
  70. GlennO

    Not a Bug AES stereo input, input 1 contains both left + right?

    Using Input 1 as digital is extremely common, especially when re-amping. I understand the request for a mode parameter for input 1, but I don't understand how the fact the Input 1 block is stereo could be considered a bug.
  71. GlennO

    Not a Bug AES stereo input, input 1 contains both left + right?

    I think you're confusing the input blocks with the hardware input ports. It's a little confusing because both are numbered 1-4. It would probably help if they were something like 1-4 and A-D.
  72. GlennO

    Not a Bug AES stereo input, input 1 contains both left + right?

    The input blocks are always stereo. Anyway, the answer to your question is still the same: Use a vol/pan block with the desired input select after the input block.
  73. GlennO

    Wish Drag/Drop swapping of Mixer block row inputs' settings

    +1 Although IMHO a better way to do the mixer block would be to have multiple input connection points. You connect a preceding block to one of the connection points and the gain and balance parameters refer to connection points, not rows. That way you can move the mixer block and the preceding...
  74. GlennO

    Not a Bug AES stereo input, input 1 contains both left + right?

    You usually do that downstream from the Input block. For example by setting the Input Select of a block to Left Only or Right Only.
  75. GlennO

    MacOs Sonoma update

    Your port settings in Axe-Edit may have changed during the course of the update, so check those.
  76. GlennO

    How to send MIDI via USB to computer?

    Alas no :).
  77. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    That's a good question and there are various ways to try to understand it. Here's my attempt: A preset contains parameters that the user can adjust and whose values are stored in presets. At the same time, the amp models that FAS develops have parameters that they adjust, most of which are...
  78. GlennO

    3 Body Problem

    It's quite a bit different than the book, but that's probably a good thing. The book is written in the Chinese style where very little happens in the main narrative. But the central point of the plot where there is an unconventional twist on a first contact story is retained and I think that...
  79. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    All the advice and instructions about resets is only relevant if you want to take full advantage of the modeling accuracy enhancements in the firmware update. If you don't care about that, you can ignore the whole reset issue. And, realistically, no matter what it says in the release notes, 99%...
  80. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    It depends on what you mean by "before". As I mentioned earlier, if you load a preset, then clear it, then add an amp block, the parameter values are retained, not reset. If the preset had no amp block when you loaded it, and you then add an amp block to it, the parameters will be reset. If you...
  81. GlennO

    Bug? Unwanted Midi messages on FM9 after Preset change

    Ok, showing the sysex messages makes it pretty clear there's a correlation. The problem happens whenever the tempo is sent at the same time as the PC. Unless there's a bug in MIDIOx, it looks like it might be a FM9 bug. By the way, I can't seem to reproduce this on my AxeFX III. A tempo message...
  82. GlennO

    Bug? Unwanted Midi messages on FM9 after Preset change

    I would turn off the sysex filter. Seeing those messages might shed some light on what's going on.
  83. GlennO

    What’s the latency on the Axe III?

    In addition to the amp and drive blocks: The pitch block adds quite a bit more latency than either the amp or drive blocks. Feedback send/return adds 16 samples. Compression lookahead also adds latency. I believe that's the entire list, aside from blocks where delay is an intended feature of the...
  84. GlennO

    Tuner Window Display Triggered via CC?

    There are various utilities available you can use to trigger a computer keystroke (in this case Cmd-T to pop up the editor tuner window and ESC to close it) from MIDI CC. For example CoyoteMIDI or Bome MIDITranslator.
  85. GlennO

    USB Audio Driver Update for Axe-Fx III, FM3, and FM9

    It’s 24 bit. The buffer size has nothing to do with the bit depth.
  86. GlennO

    Bug? Unwanted Midi messages on FM9 after Preset change

    I don't know what to tell you, but the 247 is obviously a sysex terminator, either being misinterpreted by midiox or mistransmitted by the FM9 or you've got midi streams mismerged.
  87. GlennO

    Bug? Unwanted Midi messages on FM9 after Preset change

    That's hardly a superpower. That's the function performed by any trivial midi interface :). But by involving the SY1000, you've introduced a possible source of interference for the test you're trying to perform. I'd suggest removing anything that generates midi (including FM9 Edit), except the...
  88. GlennO

    Bug? Unwanted Midi messages on FM9 after Preset change

    Looks like nonsense. If you’re sure that’s all coming from the FM9 and nothing else, e.g. FM9 Edit or a midi controller, is connected, I’d suspect the Sysex is being misinterpreted by midiox.
  89. GlennO

    Game changer for dialing presets!

    You can export a table of parametric EQ settings from REW, and you're right, you can a lot with 9 bands of EQ, but it sure would be nice if it had the ability to import a correction IR. And, as I mentioned earlier, it would be nice to see this in an audio interface that doesn't require taking...
  90. GlennO

    Game changer for dialing presets!

    Yes, you can, but that can get complicated. You need the IR applied to both the separate monitor paths from the Axe-FX and from the DAW, but not to the wet signal you're recording. And that needs to be done to all presets. That will require multiple outputs and multiple IR Player blocks. It can...
  91. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    Same thing from the front panel. My understanding of the situation is: to take full advantage of the modeling enhancements, you must to do a reset when adding a new amp block to a preset. That's a little confusing, but in practice it may not be much of an issue IF the first thing you do after...
  92. GlennO

    Game changer for dialing presets!

    You've always been able to do that with REW...there's no point in using Arc Studio for that measurement. The advantage to Arc Studio over an IR Player blocks is: it applies the correction to all audio before it reaches the speaker. Using an IR Player blocks requires you to modify all presets and...
  93. GlennO

    Game changer for dialing presets!

    If you have multiple listening positions, you can do a measurement for each position, then load the appropriate one depending on where you're sitting.
  94. GlennO

    Announcing AxeCapture: A plugin to save Axe-FX presets in your DAW project.

    Personally, I think that would be an awesome idea. Imagine all the cool things you could do with a plugin that has automatable parameters that controls an Axe-FX. Not only could you use automation lanes to control Axe-FX parameters, but you could use a DAW control surface with hardware knobs and...
  95. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    You're right, that doesn't reset the amp block. That means somebody who updates their firmware, then loads an amp block from the block library into an empty preset still needs to do a reset to take full advantage of the modelling enhancements. I'm not sure the average user will understand that...
  96. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    Everybody probably does. As I mentioned above, this is a consequence of the overlap of parameters that users adjust to tweak their presets and parameters FAS adjusts to tweak the models. That will inevitably lead to conflicts, so if you want to take full advantage of firmware updates with...
  97. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    There are so many ways though, that a user can put amp parameters into the grid. Inserting an amp block is one way, but you can also load from the block library, copy/paste blocks, import .syx file, duplicate an existing preset, load snapshots, etc. This problem is inherent in the way there is...
  98. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    I think the confusion is about the distinction between new or existing presets. Except for rare circumstances, all presets are existing presets, so a reset is almost always needed, even when starting an edit session with an empty grid. However, when working with an empty grid, the first thing...
  99. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    It looks to me like it gets the values from that preset, not from recent edits.
  100. GlennO

    Axe-Fx III Firmware 25.00 Public Beta (Cygnus X-3)

    That's my point. You have to do a reset. As far as I can tell, simply adding an amp block won't give you the new default parameter values.
Back
Top Bottom