Search results for query: *

  • Users: RossE
  • Order by date
  1. RossE

    USB 3&4 Not Connecting to Out 2

    I can get Jamtrack signal out of Output 2 in two ways. 1) Put an Out 2 block in the grid and connect it to Input 1. Set Input 1 Source = USB (Channels 3/4). In the setting I get no guitar signal at Output 2. 2) Leave Input 1 Source = ANALOG (default). Set Output 2 Copy = NONE. Again, in the...
  2. RossE

    USB 3&4 Not Connecting to Out 2

    Also worth noting, I've been a Reaper user for 10+ years, so don't think it is a user error with that config setup. I also have a Behringer X18 connected to my PC. I've considered a driver conflict, but not likely since I can get jam tracks and guitar signal both to OUT 2/headphone amp when I...
  3. RossE

    USB 3&4 Not Connecting to Out 2

    If you mean 'USB 3/4 Playback Level', it is set to 2 o'clock which should be plenty.
  4. RossE

    USB 3&4 Not Connecting to Out 2

    Thanks USMC_Trev. I don't doubt your answer, but doesn't that seem to conflict with the bit in yellow I highlighted from the manual?
  5. RossE

    USB 3&4 Not Connecting to Out 2

    I use the OUT 1 XLRs exclusively for FOH and OUT2 1/4" exclusively to a headphone amp. I'm running Reaper trying to send jam tracks to OUT 2. I'm looking to get the jam tracks and guitar signal both to OUT 2/headphone amp. I've followed the instructions in the manual. I'm running Beta 7 FW. I...
  6. RossE

    Would you sell your AX8 to buy a new FM3?

    To answer the question of the original post......yep, I would, I did and I'd do it again in a heartbeat. The FM3 rocks. Here is my post to another similar thread.
  7. RossE

    Block Library Breakdown

    Thanks Rex. I get it now. I can only save the one block definition to the library that holds consolidated settings across compressors in channels A-D. I was trying to create and save separate/distinct block definitions for each channel and then have them recalled by scene. Fog cleared...........
  8. RossE

    Block Library Breakdown

    I think I must misunderstand the purpose/capabilities of the block library. Hoping someone can set me straight, I'm trying to save my own custom block definitions to the library so I can reuse them in channels and scenes. Example: 1) I have a preset with 4 scenes. 2) I want to setup a...
  9. RossE

    Let's see those FM3 rigs!

    I'm sure the plastic film will come off sooner or later, just gonna savor it a while. All I did to modify the unit is remove/relocate one end cap. Heavily sounds like a warranty violation. Since I took great care to make sure the FM3 air flow is fully unrestricted I hope that is not the case.
  10. RossE

    Let's see those FM3 rigs!

    I made my own two button (momentary) external switch. With my setup I use Switches 1 & 3 hold for preset inc/dec. Switch 2 hold gets me the tuner. Switches 1-5 tap give me scenes 1-5. Gives me 1 row w/equidistant taps to my scenes. I use one preset per song. With 5 scenes and 4 channels to...
  11. RossE

    Debating returning my FM3 and using my AX8. Thoughts?

    I made my own. Very simple to do. Gives me 1 row w/5 equidistant taps to my 5 scenes. Before anyone questions.......Yes....there are cutouts in the sides of my switch box to allow free air flow into the FM3.
  12. RossE

    Debating returning my FM3 and using my AX8. Thoughts?

    I have added a two button external switch. I rarely used more than 5 switches on my AX8. With the new FM3 setup I use Switches 1 & 3 hold for preset inc/dec. Switch 2 hold gets me the tuner. Switches 1-5 tap give me scenes 1-5. I love this setup. I love the improved FM3 front panel access...
  13. RossE

    FM3 Firmware Release Version 1.03

    Wow! That is perfect. Thanks again for the great info and putting me on the right track
  14. RossE

    FM3 Firmware Release Version 1.03

    Killer. Thank you. My bad, I had not really dug into the stand in switches thinking they were isolated to use with the onboard switches only.
  15. RossE

    FM3 Firmware Release Version 1.03

    I don't see a FM3 enhancement requests thread, so asking here. I've only had mine for two days and have already fallen in love. Looking at how I want to utilize only three switches and the easy/cheap option of adding a dual external switch I have 3 wishes. 1) Capability to setup a dual external...
  16. RossE

    Your favorite concerts you saw in 2019?

    An Evening With Mark Knopfler
  17. RossE

    AFIII Axe-Fx 3 doing Chet Atkins (Fingerstyle)

    Nice!!!!
  18. RossE

    5 minute tones - Pitch Follower

    Did not know about this, but I can already see using it often. Killer bring Leon (and hippietim). Thank you.
  19. RossE

    Stratocaster - Try again? Or punt...

    Maybe try to find a G&L Fullerton Legacy to put your hands on an listen to.
  20. RossE

    Quality of everything is getting worse

    Cliff you should check out the Lenovo T Series. At work this refresh cycle I could choose between Mac or PC. I tried a Mac Book Pro. Horrible.... The track pad was flat unusable. I had to buy an external keyboard just to use it. I found it no more stable than a PC laptop. I got them to swap it...
  21. RossE

    One cab to rule them all

    I do a similar thing, different amps but same cabs which adds some consistency between clean and OD tones to me. Class-A style amps - Factory 122 & 180 Any style amp - Factory 169 Marshall style amps - Factory 54, 55 and 69 are always worth a listen
  22. RossE

    AX8 through a DXR10, getting hum using 1/4 inch outs

    The DXR10 has L and R inputs. If you are only plugging in one 1/4 cable from the AX8 , plug it into the L jack, then you need a dummy or null 1/4 plug in the R jack. That will do the trick....guaranteed. If you are running L and R cables from the AX8 to the DXR10 and getting noise, this...
  23. RossE

    Oscar

    I don't abstain from seeing movies, but I only see the ones I choose to see. That excludes a vast pile of them aimed at shoving Hollywood politics and morals down my throat. You couldn't pay me to sit through the Oscar's show as a whole, but I did sit just long enough to watch Lambert/Queen...
  24. RossE

    Tech is great, but let's still use our smarts

    All good points and I agree, but.........I try to make my toe tapping and pedal rocking during a gig as simple as possible. I'll use any function of the gear or suggestion from the forum to achieve that goal. Why? At 58 years of age and hard living in my younger days, I need as much of my memory...
  25. RossE

    AX8 MIDI Power Spec Question

    The schematic is the standard from the MIDI Org and shows +5v on pin 4. Not arguing whether the AX8 would work with the Relay or not, just seems it is part of the base standard. Surprises me that Fractal wouldn't adhere to the standard, but maybe actually providing voltage on pin 4 is a common...
  26. RossE

    AX8 MIDI Power Spec Question

    You may be correct. I was thinking this +5 or +3.3v power on pin 4 was part of the MIDI standard, as opposed to the 7-pin DIN power the Axe FX, Ultra and II would provide to say the Voodoo Labs Ground Control.
  27. RossE

    AX8 MIDI Power Spec Question

    I want to connect a Midi Solutions Relay to the MIDI out of my AX8. Cliff or AdminM can you answer this for me? Is the AX8 MIDI power old vs new standard or rather +5 or +3.3v? Here is the blurb from Midi Solutions FAQ. MIDI Solutions products draw power from either a MIDI Out or MIDI Thru...
  28. RossE

    Effectrode Blackbird in loop

    I just bought a Useful Arts BF-1 Tube DI to use in the effects loop of my Ax8. Though I'm still playing around with the sweetest placement in the chain and the optimum levels in/out the results have been worth the effort/cost. I've had no problems. What you plan to do is similar. If you like the...
  29. RossE

    Is there any need for a tone knob on a guitar?

    I posted a thread here a couple of years ago asking for suggestions to tame hi end edginess in my presets. Someone replied to the affect of 'you do have a tone knob you know'. I was called out and forced to admit my bad habit of avoiding the controls on my guitar. Since then I have found that...
  30. RossE

    I switched! Axe-Fx II to AX8

    I made the move from Axe II to AX8 a couple of years ago and never regretted it. I've adjusted to the limitations and love having one unit on the floor. That said, when/if a III on the floor releases I'll be making that move.
  31. RossE

    Wish Copy and paste multiple blocks

    +1 , but for AX8 Edit
  32. RossE

    Fractal User wins Young Guitarist of the Year

    Agree Hunter was incredible, the most polished and made it look fun. The young lady gets props too though....her style and composition was unique and very tasty to listen to.
  33. RossE

    Which IR do you like with the DC30?

    A bit confused on this EF-86 discussion. I see an EF-86 tube option on my AX8 in the DC-30 preamp tube options? Is it that the option is not available in the III, or cause having the option in the AX8 doesn't help much?
  34. RossE

    Phoenix

    Burleson?...and the whole time I was a stone's throw away in Granbury. Bleeding burnt orange, you know I'm wondering about your choice of final destinations. Thinking about making my last move down around Kerrvile in the next year or two.
  35. RossE

    III - Unboxing and First Impressions

    Sweet Leon. Just don't forget about your lowly AX8 tribe. Thinking we might benefit as well when you try to get some of your future killer Axe III presets as close as possible on the AX8.
  36. RossE

    Loud Tap Tempo Button Click

    I thought about this after my post. I have a soft switch that will fit the bill. Just hate to have more external stuff to mess with. Probably the best option though. Thanks.
  37. RossE

    Loud Tap Tempo Button Click

    I played on the worship team this morning and had someone from the congregation tell me they heard me making a very noticeable clicking sound on my pedal before each song. Tap tempo using the F3 button was the culprit. I have Barefoot Buttons and they definitely increase the audible click. The...
  38. RossE

    AX-8 10.00 Public Beta #2

    For the record, I'm having the same problem as Marco describes here. Loving the 10 sound/feel, but had to go back to v9.04 so the X/Y amp switching is solid. Hoping a fix for this is on the list.
  39. RossE

    Software FracPad III - iOS/Android/Mac/Win Editor for the Axe-Fx II/XL/XL+, AX8/FX8, Axe-Fx III and FM3/FM9

    Hi AlGrenadine, After my postings a few weeks ago, I'd decided to leave my Android and get an IPad. I go for a refurb Air 2. It shows up with a defective screen, I have to return it and have to wait for a replacement. It came yesterday and I bought FracPad. Just wanted to tell you I love it...
  40. RossE

    Software FracPad III - iOS/Android/Mac/Win Editor for the Axe-Fx II/XL/XL+, AX8/FX8, Axe-Fx III and FM3/FM9

    You're provided Amazon URL to the IPad adapter now only has them available used. I want a new cable. Looks like this should work and eliminate an extra adapter connection. Do you agree it looks like it should work?
  41. RossE

    Software FracPad III - iOS/Android/Mac/Win Editor for the Axe-Fx II/XL/XL+, AX8/FX8, Axe-Fx III and FM3/FM9

    Perfect...thnx!
  42. RossE

    Software FracPad III - iOS/Android/Mac/Win Editor for the Axe-Fx II/XL/XL+, AX8/FX8, Axe-Fx III and FM3/FM9

    Hi AlGrenadine, Thank you for offering to look at my fracpad_log.txt file. No need. This is the 2nd audio control app I need that my Samsung will not support. I just ordered an Ipad Air 2 refurb. Do you have a recommended 'most solid' version of IOS for the Ipad Air 2 working with FracPad?
  43. RossE

    Software FracPad III - iOS/Android/Mac/Win Editor for the Axe-Fx II/XL/XL+, AX8/FX8, Axe-Fx III and FM3/FM9

    Looked at Lineage. Instructions too scary, afraid I'd ruin my Samsung. Guess I'm out of luck. Thanks.
  44. RossE

    Software FracPad III - iOS/Android/Mac/Win Editor for the Axe-Fx II/XL/XL+, AX8/FX8, Axe-Fx III and FM3/FM9

    Hi AlGrenadine, I'm trying to check out the Fracpad demo with my AX8. I'm using a Samsung Galaxy Tab Pro 12.2 [SM-T900] running Android v5.1.1. I'm using a verfied good USB cable with an OTG adapter that is known good working with an external keyboard. When I launch Fracpad on my Android I get...
  45. RossE

    Thank you Leon Todd!

    Another +1 for Leon. I've picked up many great tips and some presets too. I can only imagine how much time and effort you put in behinds the scenes making your tutorials. I appreciate that and thank you very much!
  46. RossE

    Sooooo...what are you express(ion)ing?

    I use 1 Some presets it is just for volume. For most presets I use it to avoid toe tapping buttons. I try to make the pedal my one stop control for morphing a preset within a given song. (e.g. clean to dirty, a 5-10 db boost, enabling effects blocks on toe down). There are limitations with this...
  47. RossE

    Optimizing FRFR Volume - How?

    Thanks for all the great info guys. Sixstring......I was set to +4, trying -10 now.
  48. RossE

    Optimizing FRFR Volume - How?

    I was confused, the detent is on level knob of the Main in on the DXR10. There is no 12 o'clock detent on the Line in level.
  49. RossE

    Optimizing FRFR Volume - How?

    Well that post went 7 hours without a bite, then two great responses. Thanks very much Bman and Chris. I was beginning to think it was a stupid question. You both agree 'between 9 and 3' on the output knob. Experience rules, so I will definitely land on something within that range...
  50. RossE

    Optimizing FRFR Volume - How?

    I am the new owner of two Yamaha DXR10s. Liking them a lot. Before this my AX8 experience was totally in the headphone/IEM world. Not surprisingly, my old presets aren't translating to the DXR10s very well. However, I'm finding that most of the factory presets sound great on the DXR10s with...
  51. RossE

    Yamaha DXR-10 Line Noise Compared to a K10

    Desmo808.....yes both plugged into the same power strip. Noise goes away when TS unplugged from DXR10. Sounds like Sustainplayer, has my answer. Thanks for your input though. Sustainplayer thanks much. Just what I hoped for....a known issue with a workaround. I will test with a dummy TS plug.
  52. RossE

    Yamaha DXR-10 Line Noise Compared to a K10

    Come on now.....I know there are lot of DXR10 users out there????
  53. RossE

    Yamaha DXR-10 Line Noise Compared to a K10

    Tested a DXR10 today against a QSC K10. I used AX8 OUT 1 TS to DXR10 channel 2 L (mono) input and to the channel A input on the K10. This setup was quiet as a church mouse connected to the K10. No sound until I hit a string. With the exact same setup the DXR10 had a constant line noise buzz. Not...
  54. RossE

    RCF NX 12-SMA vs ST 12-SMA

    Thanks for all the input gents. bradlake....I do really want to give a Xitone a try. Mick is out of amps and won't have any wedges for 3 weeks or so. Rick....I do not doubt your recommendation on the NX12SMA. Many folks around here sing the same praise for it as you. Tom Morris....I hear ya...
  55. RossE

    RCF NX 12-SMA vs ST 12-SMA

    Thanks Sixstring. Good observation. I've decided to pass on the ST.
  56. RossE

    RCF NX 12-SMA vs ST 12-SMA

    Yes have looked at Xitone and exchanged a couple of emails with Mick. A couple of Xitone Active wedges are definitely on my short list, but 15% off talks loudly. Consequently, just heard from Musician's Friend that they can order RCF NX 12-SMAs, but no discount on special orders. So unless...
  57. RossE

    RCF NX 12-SMA vs ST 12-SMA

    I've been looking to buy a couple of FRFR wedges for my AX8. Just got the old 15% off Musician's Friend coupon. They carry RCF but only the ST 12-SMA. Specs show the ST is less power, a couple of pounds heavier and does not have NEODYMIUM drivers. Has anybody tried the ST compared to the NX?
  58. RossE

    Gary Richrath of REO

    Maybe my description of a cocked-wah sound it not accurate.....I just know when I added in the Detune at about 25% mix I thought it got me closer to the tone I was hearing.
  59. RossE

    Gary Richrath of REO

    Was just trying to get a Roll With The Changes tone last night. I landed on.... Brit Brown model with TS808 Mod in front of it Then a bit of the Pitch block- Detune mode to add a little of that cocked-wah vibe the tone has to my ears Give it a try.
  60. RossE

    Why are there so many d*ckheads on Facebook?

    I vowed to never have a FB account. Broke my vow to take advantage of Fractal Black Friday Sale that was supposedly only advertised there. Missed the sale, tried to remove my account and found they have insidious little hooks to keep your account open. Finally managed to get it removed and never...
  61. RossE

    X-LOAD LB-2 via JTM-45 to Axe-FX II XL+ running IR's. Video demo.

    Burgs....that sounds killer. Thanks for the demo. Unfortunately I'm stuck in a band that monitors via IEMs only in rehearsals and at gigs. I've been considering this setup to get more realism/mojo in my IEMs. Would love it if you could test your setup to IEMs only and give us your opinion if...
  62. RossE

    Integrating tube/valve amp with Axe FX II

    Hi JayCM800XL, I'm very interested in this. Would love to hear your opinion on the benefits of this setup. I am stuck using IEMs for rehearsals and gigs. Considering this to get more real amp tone/feel in my ears.
  63. RossE

    Slide Presets...please

    Geezerjohn....I tried the presets. Really like the delay block you dialed in. It added that bit of something I had been missing. I ended up trying the SLO100 CLN and was hooked immediately. Just seems to fit my guitar and the tone I hear in my head. Wouldn't have gotten there without your delay...
  64. RossE

    Slide Presets...please

    Thanks a bunch Geezerjohn. Will try those out tonight.
  65. RossE

    Slide Presets...please

    I'm hoping some of you might have a 'go to' slide preset or two you'd be willing to share. I know it is subjective, depending on the guitar used and player's skill. I've tried the tweed amps, the Car and several other amps. I've played with verb/delay/OD, as well as pickup selection and tone/vol...
  66. RossE

    Underrated or unappreciated amp blocks

    Yes....sorry CAE+.....funny how one typo propagates
  67. RossE

    Underrated or unappreciated amp blocks

    CAE3+ - Cln and Supremo Trem. Using 3 Sigma Audio Marshall G12M-25 IR variations for both. The CAE3+ cleans may be my favorites to date. Use to lean toward the Carr model, but no more. The CAE3+ has a 3D thing going on that just sounds great and feels great to play. Bright cap adjustment...
  68. RossE

    Output Comp: the AX8's secret weapon for clean tones

    I normally use the Optical 2 toward the end of the chain at Line input level. I compared CPU usage on my go to clean. With the Opto 2 my CPU is at 86%. With the Opto 2 block removed and the Amp Output Comp set to 2 the CPU is at 87%. I prefer what the Opto 2 does to the sound as it seems to have...
  69. RossE

    Jimmy Herring- Scapegoat Blues Play-Along

    Great playing and I like the tone. Would love to have this preset to noodle with. Bits of the tone remind me of old Larry Carlton Steely Dan tone.
  70. RossE

    Ebay and Reverb question

    I started using Reverb 2-3 years ago. Now I only sell on Reverb, but I will buy on eBay. I found eBay was about 9-10% fees and Reverb is 6-7%. My numbers include Payal fees because that is the expected payment method. I sold off $20k worth of studio gear on Reverb just over a year ago. It works...
  71. RossE

    AX8 with Rolls PM50s

    I don't use a PM50. I use a Rolls MX28. I send AX8 XLR out 1 to FOH. I send AX8 1/4" out 1 to the MX28. I send a mono monitor mix to the MX28 from the mixer with my mixer guitar channel at 0. I mix in my AX8 1/4" at the MX28 to hear my guitar in stereo over the mix. Works great, sounds great...
  72. RossE

    Sign In Stranger - Steely Dan

    One of my favorite SD songs. Excellent job.....love it.
  73. RossE

    Are there 'clicking' guitar knobs?

    By my count the Loknobs have 26 clicks, so 8 would be rolled back by 5-6 clicks. They come with two mounting options. One uses an adhesive ring, the other threads and tightens down on the pot. I use CTS pots and the threaded option, they are very solid. I can't speak to how well the adhesive...
  74. RossE

    Are there 'clicking' guitar knobs?

    The Loknobs from Stewmac do what you describe. I have them and like them a lot. They are tall, but not really an issue for me. They are spring loaded and lock down with Allen screws. How far you push the knobs down on the pot shaft when you lock the Allen screws determines how stiff the click...
  75. RossE

    Fractal user who's finally happy: my journey...

    Thanks for all of the suggestions folks. I went to the rehearsal space and brought one of our mains home. I've started through my presets trying to make them sound good through it. I've felt my tone through the mains has been about the same as the IEMS.....thin and raspy. I figure I'll see how...
  76. RossE

    Fractal user who's finally happy: my journey...

    Dialing in at band practice.....I won't argue that point and resolve to do it. Practical application point made. Now any technical/gear/tips/tricks to add to it. Still want to know if the Power Station could help.
  77. RossE

    Fractal user who's finally happy: my journey...

    My band is all IEM. I have an AX8. I've tried every tip I can find on the forum, third party IRs and I even just tried a Palmer PDI-03 JB replacing my cab block with it using a FX Loop block. I practice at home with tracks using the same IEMs/similar setup and my tones seem good to great. Then...
  78. RossE

    Three new Allan Holdsworth patches for Q7.02

    Man that Palmer IR blew me away. I paired it with an Ownhammer V30 IR and....it was like I found the 'missing link' for the higher gain tones I've been in search of. Thank you....Thank you..... I want more, where did you get that IR? Is there a Palmer IR pack out there somewhere for sale?
  79. RossE

    Ownhammer 112 DVRB G65

    Thanks Pima. I got this from Kevin and found it helpful........ It is open but smokey, has a smooth and a slightly dark top end (as this is one of the older/vintage originals, not the re-issues), the tell tale G65 mid bump, and a nice low mid. The cab is very open, so it's not overly wooly or...
  80. RossE

    Ownhammer 112 DVRB G65

    Anyone tried these IRs from Kevin? If so, would love to hear some comments.
  81. RossE

    Out 1 [Main] Level and Other Output Settings

    I have been wondering about the Out 1 level myself. My AX8 output is much hotter than it was on my Axe FX II Mk1. The rule of thumb for the Axe II was output level at 100%. Are we saying the recommended output level for the AX8 is 25-50%?
  82. RossE

    AX8/AxeFX Acoustic DI Tone Quest

    Thanks Brokenvail. I did not know about using them 1st in the chain. I will try that.
  83. RossE

    AX8/AxeFX Acoustic DI Tone Quest

    Thanks Brian. I bought the 3sigma audio Martin D45 IRs. I can already tell they are going to make a huge difference. Maybe my quest is over.
  84. RossE

    AX8/AxeFX Acoustic DI Tone Quest

    I've been a Fractal fanatic from the Axe Standard days through the Axe II and now the AX8. On all of them I've been able to get a passable DI only acoustic guitar tone, but never a great one. I find this baffling considering all the eq, IRs, compression, etc we have at our disposal. I've read...
  85. RossE

    AX8 - External switch reverb X/Y toggle does not work

    Working now. Thank you Joe and philipacamaniac.
  86. RossE

    AX8 - External switch reverb X/Y toggle does not work

    Mission pedal will not toggle x/y either. Wonder if my last firmware load could have been flaky. I doubt it, but may be worth a reload to see. Has anyone out there actually succeeded in doing this.....set up an external switch to toggle x/y on a block?
  87. RossE

    AX8 - External switch reverb X/Y toggle does not work

    Yes I understand your points about Ext Ctrl 1-4. I've tried them set to None and the target Pedal #, results are the same either way. I have also checked that there are no conflicting occurrences of Pedal 2 or 4 in the IO->CTRL list. I have not tried Reverb x/y toggle with my Mission...
  88. RossE

    AX8 - External switch reverb X/Y toggle does not work

    I want to run with PRESS/HOLD FOR X/Y parameter set to DISABLE to reduce the lag time between preset changes. Just recently tried this and with my less than athletic toe tapping it makes a significant difference. For global parameter changes, the only ones I have made are this one and Large...
  89. RossE

    AX8 - External switch reverb X/Y toggle does not work

    I have a Mission SP1 in Pedal Jack 1...works perfectly. I've been trying this with Pedal Jacks 2 and 4. I've tried them with the External 2/4 settings at None and Pedal 2 or 4 respectively. I just tried it on a Drive block and same thing. So it is not specific to the Reverb block, appears to be...
  90. RossE

    AX8 - External switch reverb X/Y toggle does not work

    Joe....please any ideas?
  91. RossE

    AX8 - External switch reverb X/Y toggle does not work

    I'm trying to setup an external momentary switch to toggle x/y on a reverb block on my AX8. My switch is fine and my configuration is correct because the same switch set up the same exact way toggles reverb bypass exactly as expected. I tried setting it up with the switch connected to Pedal 1...
  92. RossE

    Higher gain companion to AC15?

    I do a lot of P&W. With the 'one amp block limitation' I actually use the Class-A 30W Hot model with the treble boost drive block. For cleans I have the pedal set up in heel position to drop the amp gain and treble boost tone way down. Then to get dirty toe down brings the amp gain way up and...
  93. RossE

    Higher gain companion to AC15?

    For a high gain companion to the Vox sound, it's an easy answer for me. The Class-A 30W Hot model sounds wonderful to my ears. Give it a try if you haven't.
  94. RossE

    What sites or forums do you use when searching for used gear?

    Reverb.com is my new preferred site. Easy to barter on price, no sniping like eBay. Prices don't look great on the surface, but they are normally negotiable. Great site for selling too. Much lower fees than eBay and it works. Sold about $10k worth of gear there in 2016.
  95. RossE

    Going Stereo is just SO COOL!!!

    I use IEMs and a Rolls MX28. Whether I'm getting my mix from an IEM system or a mono feed from FOH, I take the mix to the MX28 plus a stereo output from my AX8. Then with my buds/phones driven by the MX28, my guitar is always stereo and I have full control of levels for both. Could do the same...
  96. RossE

    Fractal Audio DRIVE models: Ruckus (based on Suhr Riot)

    Lately I've been trying to build my sound around one amp.....Car Roamer. I find it to be my favorite in the box for clean and slight breakup.....to me it just has punch and pick attack like no other. So the trick was how to make it work for my high gain tones. The Ruckus was the answer. That...
  97. RossE

    The /13 FT37 is SICK

    My band plays Head East's Never Been Any Reason. I've tried many preset iterations to get the dirty cleanish tone of the main original guitar that lets the D chord work ring out clearly and still have enough balls for the power chords. Your dimed Div13 with the Timmy backed down to about 3 is...
  98. RossE

    AX8 and Eventide H9 Integration

    Understood. Thank you for clearing that up for me.
  99. RossE

    AX8 and Eventide H9 Integration

    Sorry for the delayed follow-up. Been out of pocket for a few days. Thanks for the info philipacamaniac. I have the MIDI basics working between my AX8 and H9 now. One objective was to have some of my AX8 presets send a PC change to the H9 when the AX8 footswitch is pressed. That is working...
  100. RossE

    What's your favorite Fender single coil pickup set ?

    Amalfitano SPs http://amalfitanopickups.com/pickups.php
Back
Top Bottom