We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by yek

FM9 Firmware Version 7.00

https://wiki.fractalaudio.com/wiki/index.php?title=Editors#Refresh_After_New_Firmware_AKA_.28RANF.29
- yek
- Post #162
- Yesterday at 4:18 PM
- Forum: FM9 Discussion
FM9 Firmware Version 7.00
- yek
- Post #158
- Yesterday at 3:37 PM
- Forum: FM9 Discussion
Tonex One

Should be simple to just load a couple of downloaded captures, not?
- yek
- Post #14
- Yesterday at 2:48 PM
- Forum: The Lounge
Tonex One

A nifty device who those who want to add existing profiling/captures to their existing rigs. Includes A/B, tuner, compressor, reverb, gate and tone controls. And headphones-compatible output. Below €200. That's bound to be a winner.
- yek
- Post #11
- Yesterday at 2:35 PM
- Forum: The Lounge
FM3 Firmware Version 8.00 beta 1

Post the preset.
- yek
- Post #581
- Tuesday at 5:50 PM
- Forum: FM3 Discussion
FM3 Firmware Version 8.00 beta 1

No
- yek
- Post #571
- Tuesday at 12:51 PM
- Forum: FM3 Discussion
Bug? Reset Channel doesn't work in the Controllers block

I think this is an old bug / omission. Block > Reset Current Channel (or: CTRL-i or Command-i) doesn't work in the Controllers block. On the hardware it works though. @Michael Pickens PS I post this in the Axe-Edit section, but I only tested it in FM3-Edit.
- yek
- Thread
- Sunday at 8:39 PM
- Replies: 0
- Forum: Axe-Edit III
Travel guitar recommendations?

That guitar is intriguing. @RoshRoslin , do you know how the coil split pickups on the Standard+ model sound? Any good? Any particular reason for not including a model with single coils?
- yek
- Post #16
- Sunday at 7:43 PM
- Forum: The Lounge
Franks Fractal Sunday

Hi Frank, Your previous demo series ended at preset 225, is that correct? I have listed them here: https://wiki.fractalaudio.com/wiki/index.php?title=Factory_presets#Videos So your new G66 series start at the beginning again, and goes through them 10 at a time, is that correct? @FSM
- yek
- Post #2
- Sunday at 7:32 PM
- Forum: Axe-Fx III Discussion
Axe FX II Wiki

No worries, I fully understand it. Good tip, I'll think of a way to add it.
- yek
- Post #4
- Sunday at 6:08 PM
- Forum: Axe-Fx II Discussion
My Van Halen Synth Demo

Very nice. Sounds from the hardware synth, or software?
- yek
- Post #5
- Sunday at 6:01 PM
- Forum: The Lounge
FM3 Firmware Version 8.00 beta 1

Foreign language: please use this forum section: https://forum.fractalaudio.com/forums/babels-corner.47/
- yek
- Post #536
- Sunday at 5:24 PM
- Forum: FM3 Discussion
Axe FX II Wiki

I understand your POV and request. You have a sharp eye. 👁️ Over the years I've tried to safeguard the wiki information about the previous hardware generation. But it's quite possible that some data was deleted when it became obsolete due to firmware updates for the current hardware. @Greg...
- yek
- Post #2
- Sunday at 5:23 PM
- Forum: Axe-Fx II Discussion
FM3 Firmware Version 8.00 beta 1

See first post: “Note that channel switching speed has been improved in general even with this setting turned off. ”
- yek
- Post #531
- Sunday at 4:15 PM
- Forum: FM3 Discussion
FM3 Firmware Version 8.00 beta 1

I hear a little 'click' when engaging the Input Boost, also after removing the scene controller. Still there when lowering the level. Don't know if something can be done about it.
- yek
- Post #527
- Sunday at 3:43 PM
- Forum: FM3 Discussion

Members
yek