We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by TubeByter

USB Firmware V 1.15 Release

Actually that does make me think of a similar possibility with my setup, I have our main PA power amp on the same power bar as the Mac and Axe and it does seem to coincide that I most often lose the Mac output to Axe at rehearsals, which include powering up that large amp just before we begin...
- TubeByter
- Post #24
- May 9, 2023
- Forum: Axe-Fx III Discussion
USB Firmware V 1.15 Release

Yes I can concur that on my Mac mini I'm still experiencing issue #2, the usb output is not switching to other channels, it just stops outputting. My DAW tells me that the audio is leaving it fine, there is correct activity on the output meters of the DAW but the Mac output goes silent.
- TubeByter
- Post #20
- May 2, 2023
- Forum: Axe-Fx III Discussion
Wish 2 quick wishes..

Just because I know that on the Axe it would be designed better, implemented better, and would work better than on any other device that does the same: 1) Poly tuner 2) Real-time feedback controller (for my mando, acoustics and Dobro). Yes I use parametric EQ, etc but real-time response...
- TubeByter
- Thread
- Feb 4, 2023
- Replies: 0
- Forum: Axe-Fx III Wish List
**HELP** - USB audio dropping out when using AXE Fx III as audio interface

I have the same issue with my Mac 2020 mini M1. After being on for a few hours (or days) it stops seeing the AxeIII as its audio interface, a reboot of the Axe always fixes it. I assumed it was a Mac issue, I made sure everything under 'power' settings was set to 'never sleep' but it still...
- TubeByter
- Post #12
- Dec 7, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

I think this thread has run its course. Not really into the 'baitandbicker' thing. I hope the information might prove useful to someone. Moving on now! Cheers Lou
- TubeByter
- Post #19
- May 2, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

Update... Ernie Ball does have the 6168EB mono pedal with the switch wired directly to a jack on the front.. however I don't know if the switch is a DPDT like the 6165, if it's a single throw switch (open/closed) then you would not be able to use the method I discovered to SIMULATE a momentary...
- TubeByter
- Post #17
- May 2, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

Yes again you're correct. This method that I've discovered and that is working perfectly is best described as: 'Taking a latching switch and allowing it to SIMULATE a momentary switch's action, by having both/either state of the latching switch repeatedly trigger the same event/action in the...
- TubeByter
- Post #16
- May 2, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

Absolutely. You're correct. Thanks for your help.
- TubeByter
- Post #12
- May 1, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

Short quick video of it in action: Ernie Ball 6165 pedal modded for AxeIII stand-in toggle
- TubeByter
- Post #10
- May 1, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

Well I bet it could someday.... just sayin'... Anyway turns out I don't need the soldering iron, I did connect the other pole of the latching switch to FC External switch 2, set both external sw1 and external sw2 as 'Follow Hardware/normally open-momentary make', assigned both external switches...
- TubeByter
- Post #9
- May 1, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

Thanks, I found one in my junk drawer that should fit. However I would repeat that it is possible to have software turn any latching switch into momentary by detecting the transition instead of the switch state, and generating a trigger every time any state change is detected. I believe the...
- TubeByter
- Post #7
- May 1, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

Ya may end up there.... Thinking it thru, that last idea has one fatal flaw... Every time I switch patches, if the switch on the Ernie Ball is already sitting in the state of the wrong scene, I'll have to hit it twice to get into the correct scene. Not a show stopper but annoying So... ok...
- TubeByter
- Post #4
- May 1, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

Hey I just thought of something that I'll try when I get home.. Instead of trying to use 'scene toggle' on one FC footswitch for switching in and out of solos, I will split up the scene selection... use one FC footswitch for direct selecting my 'normal' scene and another FC footswitch for...
- TubeByter
- Post #2
- Apr 30, 2022
- Forum: Axe-Fx III Discussion
Converting latching switch to momentary?

Hi all, searched around but don't see the answer to this one... I have an Ernie Ball 6165 volume/switching pedal with the added built-in 'tap left' switch. I modded the pedal so it's an expression-only pedal am using it successfully for amp volume via FC pedal input 1, andI have also wired the...
- TubeByter
- Thread
- Apr 30, 2022
- Replies: 19
- Forum: Axe-Fx III Discussion
Preset +1 on FC6 switch

Update..I only need 4 presets for tomorrow's gig so I just assigned the top 3 switches to 'direct preset select' + the preset number, and that's working great. However using the exact same procedure, if I try to set any of those switches to instead 'preset +1' it's non functional.
- TubeByter
- Post #4
- Oct 9, 2021
- Forum: Axe-Fx III Discussion