Recent content by skracus

  1. skracus

    Axe-Fx III with Synergy preamp modules and MIDI

    Here’s the rig how it’s been for a couple of years now. Took out one of the SYN2’s because I wasn’t using it enough. Pretty much just using the Plexi Module and the SLO module but the top SYN2 holds a couple Freidman modules that are used sometimes as well. All clean tones are coming from Fender...
  2. skracus

    Axe-Fx III Firmware 23.04 Release

    Does it behave the same way when not connected to the editor?
  3. skracus

    Axe-Fx III Firmware 23.04 Release

    I'm on 23.02. I use the Midi Block in every preset to send CC commands to two Synergy SYN-2's. Each scene sends the appropriate CC to bypass one of the SYN2's and select a channel on the other. No issues since updating.
  4. skracus

    Axe-Fx III Firmware 23.02 Release

    Hi Matt, When I went to FW 23.02 the Output 3 block being present in the preset DID NOT override the setting for Output 3 so everything in front of the OUTPUT 3 block in my preset was not being heard. Changing the Copy Input 1 setting to off for Output 3 solved the problem but it sounds like...
  5. skracus

    Axe-Fx III Firmware 23.02 Release

    Sounds like it. Good to know. Thank you.
  6. skracus

    Axe-Fx III Firmware 23.02 Release

    Agreed. It wasn't behaving as it should with that setting on. Here's a screen shot of the preset. It's possible I suppose that the sertting was ON all along but no longer being defeated by the block in the preset. I can't say for certain. I haven't made changes to the audio settings screen in...
  7. skracus

    Axe-Fx III Firmware 23.02 Release

    Apologies if this has already been mentioned. When I updated to 23.02 tonight from 22.01, the audio setting for Output 3 to Copy Input 1 was set to ON after the update had completed. For me this was a problem because I'm running 4CM using I/O 3 so none of the blocks feeding into the output 3...
  8. skracus

    Axe-Fx III with Synergy preamp modules and MIDI

    Yes. Still running the rig. I can share a preset once I get the rig set up. It’ll be a day or two. In a nut shell what I’m doing is using the midi block and changing CC#s for each SYN2 per scene so that only one module channel is active at a time. Check out the manual for the SYN2 and it will...
  9. skracus

    FS For Sale Axe-FX III Mk1 SOLD

    bump. One piece left.
  10. skracus

    FS For Sale Axe-FX III Mk1 SOLD

    Axe-FX III Mk1 SOLD FM3 (with HP out) SOLD FM9 Original SOLD They don't need to go but they're not being used. FM3 and FM9 are essentially new (yes they still have the plastic covers on the screens). Never left the studio, never gigged, not more than a handful of hours each. Axe-Fx III used...
  11. skracus

    Axe-Fx II/III with my Synergy SYN2/50/50

    Route as if you were using two amp blocks in parallel. I would parallel the amp block around what I show for Output 3 and Input 3 in the pic above. Mute one or the other if only using one at a time and let scenes handle the switching or set up to blend if desired.
  12. skracus

    Axe-Fx III with Synergy preamp modules and MIDI

    You're welcome!
  13. skracus

    Good signal splitter to run to inputs 1/2

    https://www.sweetwater.com/store/detail/PSplitIII--lehle-p-split-iii?utm_source=google&utm_medium=organicpla
  14. skracus

    Axe-Fx III with Synergy preamp modules and MIDI

    For setting Synergy levels I set up a preset that is nothing more than the loop the Synergy is in (in my case i go out of Output 3 and into Input 3) and a cab block. I use the midi block to change channels on the Syn2's via CC's and set up each scene in the preset to select a different channel...
  15. skracus

    Unboxing most powerful floor modeler in the UNIVERSE

    Same here and if he ever decides to move forward with it I told him I'd be interested. I applaud his work. It looks great and gave him what he was looking for. Don't pay attention to the naysayers Rik. It's awesome!
See more
Back
Top Bottom