Recent content by shireeshb

  1. S

    Axe-Fx III Firmware Version 5.05

    You know... this is yet another fantastic thing about the folks at FAS. Cliff takes time to in-service the community on this kind of stuff. Just another way he shows his commitment to the community of FAS product users. Thanks Cliff! You have few equals.
  2. S

    FIXED: Axe-Fx III Logic Issues

    Thank you so much!
  3. S

    [FIXED] Change Preset via MFC-101 selecting Scene 2 as well

    Bingo! I have CC# 120 set for Scene Increment. When I change that to None, the problem disappears. The problem was that I had IA09 and IA10 set to Scene Decrement/Increment AND the MFC was set to "Send w/ Prst" to "Yes" for those IAs. Once I set IA09 and IA10 to "Send w/ Prst" to "No"...
  4. S

    [FIXED] Change Preset via MFC-101 selecting Scene 2 as well

    No, no preset mapping. The MFC is in “None” mode, so it’s just acting like a MIDI controller. I also made sure that IA01-05 on the MFC were not set up to send multiple CC commands. The c2 setting for each is set to CC# = None. I’m considering reinstalling firmware 1.08 and seeing if the...
  5. S

    [FIXED] Change Preset via MFC-101 selecting Scene 2 as well

    No, if I change via the front panel or AxeEdit, it uses the “As Saved” setting and selects the appropriate scene.
  6. S

    [FIXED] Change Preset via MFC-101 selecting Scene 2 as well

    Thanks Chris! I had tried that very thing originally. I just tried it again to confirmed. Even if "Scene Select" is none, the preset change still selects Scene 2.
  7. S

    [FIXED] Change Preset via MFC-101 selecting Scene 2 as well

    Hi all, I'm looking to figure out what I'm doing wrong with setting up my MFC101 to work with the III over MIDI (or if I found a bug). I'm running firmware 1.09 Beta and MFC firmware 3.08. My MFC is set to have bank size = 5, so that the bottom 5 switches change presets. I've set up those...
  8. S

    Axe-Fx III and MFC-101 Mark 1

    The Faslink on the III is not the same as on the II. You’ll need to talk to the III over MIDI. If the mark I doesn’t have a MIDI out, you’re out of luck.
  9. S

    Front vs. Rear input on the Axe III

    They’re not the same on the XL+ to my knowledge
  10. S

    Axe-Fx III wait list: Let us know when you get notified...

    Waitlist: 1/29/2018 at 9:33 PM (Eastern) Invite received: 5/8/2018 at 1:08 PM (Eastern) Ordered minutes later! WOO HOO!!!
  11. S

    Axe FX XL+ with Mesa Mark V Experiences ?

    Yes, I am using the MFC to change patches and, accordingly, make the necessary changes on the Mark V. I haven't looked hard enough to see if your can use Scene changes to toggle changes in the MAG. I think the MAG is more built to respond to the program change MIDI commands associated with...
  12. S

    Axe FX XL+ with Mesa Mark V Experiences ?

    I have the XL+ and Mark V, set up in the 4CM. I am using the Mini Amp Gizmo to do the switching over MIDI. Works great for me. I can't comment on the noise levels, but, at my volume levels (loud basement levels :) ), I have no complaints.
  13. S

    New User, 2 Dumb Questions

    I think 2) is because of the Auto-engage setting being set to Medium Speed. Try setting that to off.
  14. S

    Mesa Boogie Mark V + Axe FX 2 + MFC-101

    I have the same rig and I have NOT been able to get scene changes to cause channel changes on the Mark V via the Mini Amp Gizmo. I think the Amp Gizmo only responds to Program Change MIDI commands. I think Scene changes are CC commands. Would love to be corrected though... :)
  15. S

    Somebody stop me! (getting my MASK on) ... Boogie MK V Combo

    I have a Mark V head and an AxeFx. The V sounds awesome even at low volumes, but, if your looking for versatility, stick with your AxeFx. You can also consider the 4CM with the V combo for your effects.
See more
Back
Top Bottom