We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by RossE

USB 3&4 Not Connecting to Out 2

I can get Jamtrack signal out of Output 2 in two ways. 1) Put an Out 2 block in the grid and connect it to Input 1. Set Input 1 Source = USB (Channels 3/4). In the setting I get no guitar signal at Output 2. 2) Leave Input 1 Source = ANALOG (default). Set Output 2 Copy = NONE. Again, in the...
- RossE
- Post #9
- May 25, 2020
- Forum: FM3 Discussion
USB 3&4 Not Connecting to Out 2

Also worth noting, I've been a Reaper user for 10+ years, so don't think it is a user error with that config setup. I also have a Behringer X18 connected to my PC. I've considered a driver conflict, but not likely since I can get jam tracks and guitar signal both to OUT 2/headphone amp when I...
- RossE
- Post #6
- May 25, 2020
- Forum: FM3 Discussion
USB 3&4 Not Connecting to Out 2

If you mean 'USB 3/4 Playback Level', it is set to 2 o'clock which should be plenty.
- RossE
- Post #5
- May 25, 2020
- Forum: FM3 Discussion
USB 3&4 Not Connecting to Out 2

Thanks USMC_Trev. I don't doubt your answer, but doesn't that seem to conflict with the bit in yellow I highlighted from the manual?
- RossE
- Post #3
- May 25, 2020
- Forum: FM3 Discussion
USB 3&4 Not Connecting to Out 2

I use the OUT 1 XLRs exclusively for FOH and OUT2 1/4" exclusively to a headphone amp. I'm running Reaper trying to send jam tracks to OUT 2. I'm looking to get the jam tracks and guitar signal both to OUT 2/headphone amp. I've followed the instructions in the manual. I'm running Beta 7 FW. I...
- RossE
- Thread
- May 25, 2020
- Replies: 11
- Forum: FM3 Discussion
Would you sell your AX8 to buy a new FM3?

To answer the question of the original post......yep, I would, I did and I'd do it again in a heartbeat. The FM3 rocks. Here is my post to another similar thread.
- RossE
- Post #9
- May 25, 2020
- Forum: AX8 Discussion
Block Library Breakdown

Thanks Rex. I get it now. I can only save the one block definition to the library that holds consolidated settings across compressors in channels A-D. I was trying to create and save separate/distinct block definitions for each channel and then have them recalled by scene. Fog cleared...........
- RossE
- Post #3
- Apr 28, 2020
- Forum: FM3 Discussion
Block Library Breakdown

I think I must misunderstand the purpose/capabilities of the block library. Hoping someone can set me straight, I'm trying to save my own custom block definitions to the library so I can reuse them in channels and scenes. Example: 1) I have a preset with 4 scenes. 2) I want to setup a...
- RossE
- Thread
- Apr 28, 2020
- Replies: 7
- Forum: FM3 Discussion
Let's see those FM3 rigs!

I'm sure the plastic film will come off sooner or later, just gonna savor it a while. All I did to modify the unit is remove/relocate one end cap. Heavily sounds like a warranty violation. Since I took great care to make sure the FM3 air flow is fully unrestricted I hope that is not the case.
- RossE
- Post #222
- Apr 24, 2020
- Forum: FM3 Discussion
Let's see those FM3 rigs!

I made my own two button (momentary) external switch. With my setup I use Switches 1 & 3 hold for preset inc/dec. Switch 2 hold gets me the tuner. Switches 1-5 tap give me scenes 1-5. Gives me 1 row w/equidistant taps to my scenes. I use one preset per song. With 5 scenes and 4 channels to...
- RossE
- Post #216
- Apr 23, 2020
- Forum: FM3 Discussion
Debating returning my FM3 and using my AX8. Thoughts?

I made my own. Very simple to do. Gives me 1 row w/5 equidistant taps to my 5 scenes. Before anyone questions.......Yes....there are cutouts in the sides of my switch box to allow free air flow into the FM3.
- RossE
- Post #35
- Apr 23, 2020
- Forum: FM3 Discussion
Debating returning my FM3 and using my AX8. Thoughts?

I have added a two button external switch. I rarely used more than 5 switches on my AX8. With the new FM3 setup I use Switches 1 & 3 hold for preset inc/dec. Switch 2 hold gets me the tuner. Switches 1-5 tap give me scenes 1-5. I love this setup. I love the improved FM3 front panel access...
- RossE
- Post #5
- Apr 22, 2020
- Forum: FM3 Discussion
FM3 Firmware Release Version 1.03

Wow! That is perfect. Thanks again for the great info and putting me on the right track
- RossE
- Post #63
- Apr 16, 2020
- Forum: FM3 Discussion
FM3 Firmware Release Version 1.03

Killer. Thank you. My bad, I had not really dug into the stand in switches thinking they were isolated to use with the onboard switches only.
- RossE
- Post #60
- Apr 16, 2020
- Forum: FM3 Discussion
FM3 Firmware Release Version 1.03

I don't see a FM3 enhancement requests thread, so asking here. I've only had mine for two days and have already fallen in love. Looking at how I want to utilize only three switches and the easy/cheap option of adding a dual external switch I have 3 wishes. 1) Capability to setup a dual external...
- RossE
- Post #58
- Apr 16, 2020
- Forum: FM3 Discussion