Recent content by reilly

  1. reilly

    What cable for 4CM?

    www.Pedalsnake.com
  2. reilly

    X’s Journey w/ a PRS MT 15 & the FX8....

    Cool videos, I love my FX8!! It has worked with every amp I have tried/owned. I also Own the Runt 50 head and matching cab and a BE 412. I have been able to do channel switching with the Archon 100 as well with no other gear other than a Pedal Snake cable. FX8 works perfectly and will also...
  3. reilly

    Post-whatever players, what's your FX8 setup?

    This is my normal giging rig, simple but allows for a lot of tones and effects. I use a lot of delays and pitch as well as a Over Drive in front to get the gain and response i am looking for. The pc editor makes it easy to create cool sounds. Www.imbuedmusic.com
  4. reilly

    Mesa Mark IV channel switching

    Look at www.pedalsnake.com
  5. reilly

    Mesa Mark IV channel switching

    Yes one cable with a splitter on the end will do the trick (stereo to dual mono) that’s how I ran mine
  6. reilly

    Mesa Mark IV channel switching

    I ran a trs to a split Ts from the fx8 using only one control switch output, you could also use both of the control switch outputs using just a ts cable from each. you can switch between all 3 channels on the amp. I was not using my amps reverb or any simulclass switching just kept it simple...
  7. reilly

    Bandmates complaining about tone....

    I had some great tones with very little effert when I was using the Mesa Mark Iv and fx8, I used the amps Distortion with a od in front (if needed) and it sounded great. The fx8 is a great unit and the mark Iv is awesome as well, for me though I am not a fan of how the mark series sounded on the...
  8. reilly

    What type of FX8 rig are you running?

    I run my FX8 (4 cable method) into a Friedman Runt 50 and matching Friedman 2x12 cab
  9. reilly

    [Solved] FX loop issue on the JP-2C with FX8

    Don’t plug in the footswitch with the midi at the same time (says so in the manual) check your midi cc to make sure the loop is staying on
  10. reilly

    FX8 relay channel switching the 5150 IIIs with the Bestronics cable

    Pm me with an email and I will get you a few patches
  11. reilly

    FX8 relay channel switching the 5150 IIIs with the Bestronics cable

    I just checked Red channel Relay 1 set to tip R1 mode is lat Relay 2 is off Green channel Relay 1 is tip Relay 2 is both Blue channel I think its ring or sleave for relay 1
  12. reilly

    FX8 relay channel switching the 5150 IIIs with the Bestronics cable

    I don't have my EVH anymore but make sure you are using two relay blocks, I think I still have some presets on my fx8 I could email them to you. You just need to find the right combo of ring, tip sleeve between the relays
  13. reilly

    5150 100 watt gizmo question

    You don't need the amp gizmo for the evh 50w since it has midi built into the amp (I had a 50w evh for a short time and was able to get it to work with midi and the fx8) Back to the 100w can you use the stock footswitch cable? (7 pin midi) or do you need to buy the special rjm evh cable that...
  14. reilly

    5150 100 watt gizmo question

    I was about to go the mini amp gizmo route until I found out about the custom cable.
  15. reilly

    5150 100 watt gizmo question

    Yes, you use the relay ports, effects loop will always be "on" but that does not bother me, a 25 foot cable cost me $75 shipped, still much cheaper than a mini amp gizmo plus cable. I just made a bank for my Evh 5150 iii 100w and separate bank for my Mesa JP-2C, aside from the relay settings I...
See more
Back
Top Bottom