• We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

    Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by Megahertzz

  1. Megahertzz

    XLR splitter to put between Output 1 and monitors/FOH

    I've taken this a step further and I am now considering whether it would be possible to add a stereo volume control to one of the mini module slots on the Templeboard, right next to the monitor outputs. My plan is to split Output 1 Left and Right into two separate outputs, where one pair of outs...
  2. Megahertzz

    OMG 9 without FC-6. How to use the 3 switches by themselves to do everything!

    Am I understanding it correctly that this is the OMG9 layout with the OMG3 in the free layout spots? All I have to do to switch between them is change bank size and startup layout?
  3. Megahertzz

    XLR splitter to put between Output 1 and monitors/FOH

    It seems this is the route to go. Thanks for the tip.
  4. Megahertzz

    XLR splitter to put between Output 1 and monitors/FOH

    The idea was to avoid using Output 2, so I could put my Whammy pedal in the loop.
  5. Megahertzz

    XLR splitter to put between Output 1 and monitors/FOH

    I'm looking for a splitter to put on (under) my pedalboard, but I have had no luck with Google. Maybe what I'm looking for doesn't exist (yet)? What I want is a passive splitter with 2 inputs and 4 outputs, where two of the L/R outputs go directly through the splitter (to FOH), and the other...
  6. Megahertzz

    Wish Secondary tap function for footswitches

    Nevermind, I'm an idiot. :weary:
  7. Megahertzz

    Wish Secondary tap function for footswitches

    Couldn't find out how in the switches setup. Can only find tap and hold function, not additional taps.
  8. Megahertzz

    Wish Secondary tap function for footswitches

    +1 for this. My wish is to be able to, for instance, use SW1 to toggle between Scene 1 and 2, SW2 toggles Scene 3 an 4 etc. It would also be very helpful to have a 3rd and 4th, even 8th press function on each switch if so desired. Imagine using one switch to increase scene# for each press of...
  9. Megahertzz

    I use the ML USA Djent cab pack from the Fractal site, but Leon Todds IRs also work very well...

    I use the ML USA Djent cab pack from the Fractal site, but Leon Todds IRs also work very well with my preset. You could also try any of the 4x12 V30 IR's in the factory cabs. It's been a few firmware updates since i posted the preset, so the amp block might need a little tweaking.
  10. Megahertzz

    Wish I/O Routing Matrix

    +1 More options for routing USB would be nice. Headphone output should also be a separate routable port.
  11. Megahertzz

    Expression Pedal Calibration Question

    Downloaded a MIDI monitor, but couldn't figure out how to use it. However, I don't think the MMGT is the issue. I tried calibrating it the way @JoKeR III suggested, still stopped at the same values in their respective blocks. Did a full reset of the MIDI config in the Axe, which seems to have...
  12. Megahertzz

    Expression Pedal Calibration Question

    I'm reviving this thread because it's still an issue for me. FX3 FW. 14.00, MMGT22 FW. 4.5.1. Mission pedals connected to the MMGT22 have been calibrated several times, still maxes out at 9.92 on wah block, 9.84 on volume block, and most annoying, 98.4 on pitch block. After a few seconds it...
  13. Megahertzz

    FM3/FC6 (OMG9) board setups?

    I'm considering putting the FM3 and FC6 on two separate boards, with one Mission EP-1 on each board, plus a Shure GLXD16 on the board with the FM3 and Mission Pedal. @2112 does the NUX Bumblebee fit both the Mission pedal and the GLXD16 together with the FM3 do you think?
  14. Megahertzz

    For those that have an Axe-Fx III and an FM3

    I currently own an FX3, and expect my FM3 will arrive late September. The way I see it, the FM3 is small multitool you bring with you when the entire toolbox is too much hassle. I'm most likely to use the FM3 for practice and eventual flying single gigs, and the FX3 for gigs within driving...
  15. Megahertzz

    Implemented Output Parametric EQ

    I think @2112 in one of his videos explained why he used EQ blocks instead of the global EQ, and I think he's really on to something. EQ blocks, both parametric and graphic, can be saved as global blocks, so when you adjust the EQ of one preset, it will apply for all presets using that saved...
Top Bottom